CONVECTOR Submittal Specification

SR-A / SRG-A Flat Top Cabinet Semi-Recessed 3 Sided Overlap

Brand: Vulcan

General Specifications

Model Types

SR-A Open Inlet
SRG-A Louvered Inlet

Front and Liner

Style: Front Outlet

Outlet: Stamped Louvers, Pencil Proof

Lengths

20" through 64" in 4" Increments

Materials

Cabinet Front and Liner:

18 Ga./20 Ga. CRS (Std)*
18 Ga./18 Ga. CRS (Opt'l)
16 Ga./20 Ga. CRS (Opt'l)*
16 Ga./18 Ga. CRS (Opt'l)
16 Ga./16 Ga. CRS (Opt'l)
14 Ga./20 Ga. CRS (Opt'l)*
14 Ga./18 Ga. CRS (Opt'l)
14 Ga./16 Ga. CRS (Opt'l)
14 Ga./14 Ga. CRS (Opt'l)
*Liner is Galvannealed Steel
18 Ga./20 Ga. SS (Opt'l)
18 Ga./18 Ga. SS (Opt'l)
16 Ga./20 Ga. SS (Opt'l)
16 Ga./18 Ga. SS (Opt'l)
16 Ga./16 Ga. SS (Opt'l)

Finish

Baked Powder Prime
Baked Powder Color (Opt'l)

Coil Specifications

Element: Bronze Header 3/4" NPT w/Copper Tube/Alum Fins (Mechanically Expanded).

Header Connections

Single Header Both Ends (Std)
Single Inlet 1 End / Dual Inlet 1 End (Opt'l)
Dual Inlet Both Ends (Opt'l)

Optional Accessories

Damper

Damper Blades Factory Installed
Knob Damper (Opt'l)
Tamper Resistant (Opt'l)

Access Doors

(Opt'l)

Insulation

Back Only (Opt'l)
Back, Sides, Top (Opt'l)

Piping Knockout

(Opt'l)

4" End Pockets

LH (Opt'l)
RH (Opt'l)
Both Ends (Opt'l)

Perforated Front

Consult Factory

16 Ga. (Opt'l)

14 Ga. (Opt'l)

Model Dimensions (Type SR-A / SRG-A)

MODEL	D	L	H	B	J
4xx-16	16	20,24,28, 32,36,40, 44,48,52, 56,60,64,	16	2-1/8	2
4xx-18	18		18
4xx-22	4-1/4		22
4xx-24	24		24
4xx-30	30		30
6xx-16	16	20,24,28, 32,36,40, 44,48,52, 56,60,64,	16	3-1/8	4
6xx-18	18		18
6xx-22	6-1/4		22
6xx-24	24		24
6xx-30	30		30
8xx-16	16	20,24,28, 32,36,40, 44,48,52, 56,60,64,	16	4-1/8	6
8xx-18	18		18
8xx-22	8-1/4		22
8xx-24	24		24
8xx-30	30		30

Note: When adding end pockets, liner and front length increase.

Diagram: Convector Outline

A diagram illustrates the convector's profile, showing the relationship between 'D' (depth), 'L' (length), and 'H' (height). It indicates a wall mounting configuration with a damper, adjustable field settings, and louvers. Key dimensions are labeled, including the overall length ('L'), depth ('D'), and height ('H'). The diagram also shows the placement of the outlet louvers and the base/floor.

Steam Ratings in BTU/H (215°F at 65°F EAT)

Type SR-A

DEPTH INCHES	LENGTH INCHES	FRONT OUTLET, NOMINAL LINER HEIGHT *TYPE SR-A
DEPTH INCHES	LENGTH INCHES	16"	18"	22"	24"	30"
20	2230	2495	2830	2930	3120
24	2760	3145	3625	3720	3985
28	3310	3815	4345	4465	4775
32	3865	4490	5110	5255	5665
36	4370	5160	5880	6025	6505
40	4895	5810	6600	6790	7320
44	5425	6480	7390	7560	8160
48	5950	7105	8110	8350	8975
52	6550	7800	8855	9070	9745
56	7030	8450	9625	9865	10630
60	7655	9120	10345	10610	11400
64	8135	9790	11135	11400	12290
20	3240	3625	4250	4390	4850
24	4030	4560	5375	5570	6170
28	4850	5520	6480	6670	7370
32	5615	6480	7610	7870	8690
36	6430	7390	8690	9025	9935
40	7250	8375	9815	10200	11230
44	8065	9290	10920	11350	12480
48	8880	10250	12025	12455	13705
52	9745	11185	13105	13535	14905
56	10510	12145	14230	14735	16225
60	11400	13055	15310	15840	17425
64	12190	14040	16440	17065	18770
20	4030	4535	5040	5135	5570
24	5110	5760	6360	6575	7105
28	6385	6960	7680	7895	8520
32	7560	8185	9025	9310	10055
36	8710	9385	10390	10705	11545
40	9865	10630	11760	12070	13055
44	11040	11830	13055	13440	14545
48	11950	12935	14400	14810	16080
52	13465	14230	15670	16105	17425
56	14615	15505	17090	17570	19010
60	15770	16655	18335	18840	20375
64	16775	17880	19750	20330	21960

Type SRG-A

DEPTH INCHES	LENGTH INCHES	FRONT OUTLET, NOMINAL LINER HEIGHT *TYPE SRG-A
DEPTH INCHES	LENGTH INCHES	16"	18"	22"	24"	30"
20	2163	2420	2773	2871	3089
24	2677	3051	3553	3646	3945
28	3211	3701	4258	4376	4727
32	3749	4355	5008	5150	5608
36	4239	5005	5762	5905	6440
40	4748	5636	6468	6654	7247
44	5262	6286	7242	7409	8078
48	5772	6892	7948	8183	8885
52	6354	7566	8678	8889	9648
56	6819	8197	9433	9668	10524
60	7425	8846	10138	10398	11286
64	7891	9496	10912	11172	12167
20	3046	3408	4038	4171	4753
24	3788	4286	5106	5292	6047
28	4559	5189	6156	6337	7223
32	5278	6091	7230	7477	8516
36	6044	6947	8256	8574	9736
40	6815	7873	9324	9690	11005
44	7581	8733	10374	10783	12230
48	8347	9635	11424	11832	13431
52	9160	10514	12450	12858	14607
56	9879	11416	13519	13998	15901
60	10716	12272	14545	15048	17077
64	11459	13198	15618	16212	18395
20	3667	4127	4687	4776	5403
24	4650	5242	5915	6115	6892
28	5810	6334	7142	7342	8264
32	6880	7448	8393	8658	9753
36	7926	8540	9663	9956	11199
40	8977	9673	10937	11225	12663
44	10046	10765	12141	12499	14109
48	10875	11771	13392	13773	15598
52	12253	12949	14573	14978	16902
56	13300	14110	15894	16340	18440
60	14351	15156	17052	17521	19764
64	15265	16271	18368	18907	21301

Correction factors for BTU performance at different Average Water Temperatures are available in Table 3. For other applicable correction factors, see the Correction Factors page. For assistance with ratings and selection, please use the online Specifier tool.

Correction Factors

Table 3: Convector BTU Correction Factors

Based on Section 35.4 ASHRAE HVAC Systems and Equipment

AVERAGE WATER TEMPERATURE (°F)	ENTERING AIR TEMPERATURE (°F)
AVERAGE WATER TEMPERATURE (°F)	55°	60°	65°	70°	75°
100°	0.17	0.14	0.12	0.09	0.07
110°	0.23	0.20	0.17	0.14	0.12
120°	0.29	0.26	0.23	0.20	0.17
130°	0.35	0.32	0.29	0.26	0.23
140°	0.43	0.39	0.35	0.32	0.29
150°	0.50	0.46	0.43	0.39	0.35
160°	0.58	0.54	0.51	0.47	0.43
170°	0.67	0.63	0.58	0.54	0.51
180°	0.76	0.71	0.67	0.63	0.58
190°	0.85	0.81	0.76	0.71	0.67
200°	0.95	0.90	0.85	0.81	0.76
210°	1.05	1.00	0.95	0.90	0.85
215° (STD)	1.10	1.05	1.00	0.95	0.90
220°	1.15	1.10	1.05	1.00	0.95
230°	1.26	1.20	1.15	1.10	1.05
240°	1.37	1.32	1.26	1.21	1.15
250°	1.47	1.43	1.37	1.32	1.27

Table 4: Correction Factors for Steam Pressures Other Than 1 PSI GAUGE*

FACTOR	PRESSURE PSI GAUGE
FACTOR	5	10	15	20	25	50
1.12	1.25	1.36	1.46	1.56	1.93

*Apply factors shown above to the ratings shown on the 215°F ratings page.

Note: Maximum Recommended operating pressure 150 PSIG, (365.9°F). For conversion from steam to hot water, use correction factors shown in Table 3.

Table 5: Correction Factors for Access Doors

Length	Free Standing, Non-Recessed Non-Standard Access Door Locations				Semi-Recessed or Fully Recessed Non-Standard Access Door Locations
Length	3 or 4	3 & 4	5 or 6	5 & 6	3 or 4	3 & 4	5 or 6	5 & 6
20"	0.940	0.880	0.820	0.650	0.975	0.950	0.925	0.850
24"	0.950	0.910	0.860	0.720	0.980	0.960	0.940	0.880
28"	0.960	0.920	0.890	0.770	0.982	0.968	0.948	0.902
32"	0.970	0.940	0.890	0.800	0.985	0.972	0.955	0.918
36"	0.970	0.940	0.920	0.830	0.988	0.975	0.962	0.925
40"	0.970	0.950	0.920	0.850	0.990	0.978	0.970	0.932
44"	0.980	0.950	0.930	0.860	0.990	0.980	0.970	0.940
48"	0.980	0.960	0.940	0.880	0.990	0.982	0.970	0.948
52"	0.980	0.960	0.950	0.890	0.992	0.985	0.978	0.955
56"	0.980	0.960	0.950	0.890	0.992	0.985	0.978	0.955
60"	0.980	0.970	0.950	0.900	0.992	0.985	0.978	0.955
64"	0.980	0.970	0.950	0.910	0.992	0.988	0.978	0.962

Note: Derating factors do not apply to units with end pockets.

Table 6: Pressure Loss in Feet of Water

Charted figures showing pressure drop through Convectors with forced hot water. Used for determining pressure head requirement. Based on 64" length units, but applicable to shorter units, as most loss is due to headers.

WATER FLOW IN GPM	4 INCH MODELS	6 INCH MODELS	8 INCH MODELS
.25	0.044	--	--
.50	0.160	0.070	0.046
1	0.597	0.270	0.167
2	2.220	1.047	0.616
3	--	2.260	1.367
4	--	3.793	2.380
5	--	--	3.673

Table 7: Gallons Per Minute of Hot Water Required

This is a graph illustrating the relationship between MBH (Thousands of BTU per Hour) on the x-axis and GPM (Gallons Per Minute) on the y-axis. It shows different lines representing various temperature drops (10°F, 20°F, 30°F, 40°F) for hot water flow.

Table 8: Output-Flow Rate Corrections

Convector Depth	Tubes per Element	GPM	MBH Based on T.D. & Min. Flow Rate
Convector Depth	Tubes per Element	GPM	Min. Flow Rate (0.25 Ft./Sec.)	10TD	20TD	30TD	40TD
4"	2	0.15	0.750	1,500	2,250	3,000
6"	3	0.225	1.125	2,250	3,375	4,500
8"	4	0.30	1.500	3,000	4,500	6,000

Note: Table 8 shows MBH which result at specific water temperature drops and minimum water flow rates which are required to maintain turbulent flow within element tubes.

Diagram: Convector Coil

A diagram details the convector coil construction. It specifies coil sizes based on the number of tubes: 4" depth has a 2-tube element (3 3/4" width), 6" depth has a 3-tube element (5 3/4" width), and 8" depth has a 4-tube element (7 3/4" width). The diagram shows the end-to-end length being the liner length less 1/2", and riser centers being the liner length less 2 1/2". It also indicates a 3/4" NPT typical connection, a vent plug, and a 3-position hanger welded to the liner. A note clarifies that when ordering with end pockets, the overall physical length increases by 4" per pocket, while the coil length remains standard. Coil fins are 2-1/2" high and mechanically bonded to copper tubes at 6 fins per inch.

Contact Information

Vulcan

260 North Elm St., Westfield, MA 01085

(413) 568-9571

www.vulcanrad.com

Project: [Project Name Placeholder]

Location: [Location Placeholder]

Architect: [Architect Placeholder]

Engineer: [Engineer Placeholder]

Contractor: [Contractor Placeholder]

PO Number: [PO Number Placeholder]

Date: [Date Placeholder]

	Vulcan RF-A/RFG-A Convector Submittal Specification Detailed submittal specification for Vulcan RF-A and RFG-A series recessed flat top convectors, including features, materials, dimensions, and performance data.
	Vulcan PW-A/PWG-A Convector Specification \| Submittal Data Detailed submittal specification for Vulcan PW-A and PWG-A convector heaters, including BTU ratings, dimensions, materials, correction factors, and pressure loss data.
	Vulcan FWG-A Louvered Inlet Convector Specification Sheet Detailed specifications, performance data, and correction factors for the Vulcan FWG-A Front Outlet Recessed Louvered Inlet Convector. Includes material, finish, and accessory options.
	Vulcan Convector Heaters: Product Catalog, Specifications, and Selection Guide Comprehensive guide to Vulcan Convector Heaters, including Sterling Convectors. Features product types, specifications, installation data, capacity tables, and selection tools for HVAC professionals.
	Vulcan FS-A/FSG-A Convector Submittal Specification and Ratings Detailed submittal specification for Vulcan FS-A and FSG-A flat top convector cabinets, including dimensions, materials, finishes, optional accessories, steam ratings, and correction factors for various operating conditions. Suitable for wall or floor mounting.
	LINOVECTOR II: Copper/Aluminum and Steel Finned Tube Unit Specifications and Design Data Comprehensive submittal specification and design data for Vulcan LINOVECTOR II finned tube units, detailing enclosure options, element specifications, performance ratings, correction factors, and technical data for HVAC applications.
	Vulcan V Series HDR Gas Ranges Operations Manual Comprehensive operations, installation, and maintenance manual for Vulcan V Series HDR Gas Ranges. Includes safety guidelines, configuration details, troubleshooting, and cleaning procedures.
	Vulcan VFRY18 Series Heavy Duty Range Match Fryer: Specifications & Installation Comprehensive specifications, standard and optional features, and installation instructions for the Vulcan VFRY18 Series Heavy Duty Range Match Fryer. This commercial-grade gas fryer offers a 45-50 lb capacity and is designed for professional kitchens.