MAULjura 825 71 LED Lamp

Intended Use

The MAULjura 825 71 lamp is designed for high-precision work in dry indoor areas such as homes, offices, or workshops. It is suitable for ambient temperatures between -10°C and +40°C with a relative humidity of up to 95%. The luminaire is intended for mounting on horizontal surfaces.

General Safety Instructions

Please read all enclosed operating instructions and information carefully and keep them for future reference.

• Observe all warnings in the documentation and on the device.
• Use the luminaire only when it is technically flawless and with awareness of dangers and risks.
• National safety regulations must be followed for installation and operation.
• Install the lamp only on a suitable surface using appropriate mounting materials.
• This lamp is intended for illuminating indoor rooms and work areas.
• Do not mount the luminaire in dry and closed spaces only.
• Do not operate the lamp in potentially explosive atmospheres, as this can lead to explosions and severe injury or death.
• Installation, repairs, and disassembly should only be performed by a qualified electrician unless otherwise stated.
• Connect the luminaire to a power supply with a protective earth conductor.
• Verify that the available mains voltage matches the operating voltage and frequency specified on the type plate.
• Damaged luminaires must not be used.
• Always disconnect the lamp from the power supply before working on it.
• Do not alter or modify the luminaire.
• Do not hang anything from or attach anything to the lamp.
• Do not cover the luminaire.
• Do not leave children unattended with the luminaire; it is not suitable for children.
• Dispose of packaging according to local regulations.
• Disconnect the lamp from the power supply and allow it to cool down before cleaning and maintenance.
• Clean only with a dry, soft, and lint-free cloth.
• If the external flexible cable or cord is damaged, it must be replaced by the manufacturer, their service agent, or a similarly qualified person (electrician) to avoid hazards.
• For light source replacement, consult the respective operating instructions or packaging to determine if a trained electrician or qualified person is required.

Technical Specifications & Features

• Protection Class: Electrical Protection Class II, no protective earth conductor required due to sufficient insulation between live and touchable parts.
• Usage Area: For use in dry indoor areas only.
• Dimmable: Yes.
• Beam Angle: Half intensity angle (beam angle) indicated as 100°.
• Power: 65W
• Voltage: 200-240V~, 50/60 Hz
• Connection: CEE 7/4 power plug.
• Cable Length: Approximately 2.50 meters.
• LED Light Source: Replaceable by a qualified electrician.
• Operating Device: Replaceable by a qualified electrician.
• Conformity: MAUL declares that these lamps conform to European Directives and product-specific directives.
• Disposal: Do not dispose of in unsorted household waste. Dispose of as electrical waste at designated collection facilities. Contact local authorities for disposal options.

Assembly Instructions

The following parts are included:

• 1 x Base Component
• 1 x Lamp Head/Fixture
• 1 x Lower Lamp Pole Section
• 1 x Upper Lamp Pole Section
• 6 x M4 x 25 screws
• 2 x M4 x 10 screws
• 6 x Ø4.2 washers
• 1 x SW3 Allen key
• 1 x SW2.5 Allen key
• 1 x Power Cable

Step 1: Attach the base component (1) to the lower pole section (3) using three M4 x 25 screws (5), three Ø4.2 washers (7), and the SW3 Allen key (8). (Diagram shows base being attached to the bottom of the pole, with screws and washers inserted from the side into the base and pole.)

Step 2: Connect the lower pole section (3) and the upper pole section (4). (Diagram shows two sections sliding together, with a connector inside.)

Step 3: Attach the upper pole section (4) to the base assembly (1) using two M4 x 10 screws (6) and two Ø4.2 washers (7), and the SW2.5 Allen key (9). (Diagram shows the upper pole section being attached to the base, with screws inserted from the side.)

Step 4: Attach the lamp head/fixture (2) to the end of the upper lamp pole section (4) using three M4 x 25 screws (5), three Ø4.2 washers (7), and the SW3 Allen key (8). (Diagram shows the lamp head being attached to the end of the pole.)

Step 5: Connect the power cable (10) to the lamp. (Diagram shows the CEE 7/4 power plug being inserted into the socket on the lamp's pole.)

Operation

The lamp features a control for ON/OFF and dimming, typically a rotary knob. Turning the knob clockwise increases brightness (maximal), and counter-clockwise decreases it (dim). Pressing the knob turns the lamp ON/OFF.

• ON/OFF: Press the control knob.
• Dimming: Rotate the control knob. Clockwise increases brightness (maximal), counter-clockwise decreases brightness (dim).

Spare Parts

The following spare parts are available:

• 2 x LED Light Strips (Art.-No.: 8257109.205)
• 1 x LED Driver (Art.-No.: 8257109.210A)
• 1 x Lamp Pole Assembly (Art.-No.: 8257109.220)
• 5 x LED Light Strips (Art.-No.: 8257109.200)

Energy Efficiency Information

This product contains light sources with energy efficiency class < D >.

• Product with five light sources: Energy efficiency class < D > (Art.-No.: 8257109.200)
• Product with two light sources: Energy efficiency class < D > (Art.-No.: 8257109.205)

This information is provided in multiple languages within the original document.

Company Information

License Holder Name: Jakob MAUL GmbH

License Holder Address: Jakob-Maul-Str. 17; D-64732 Bad König

Telephone: +49 (0)6063/502-100

Fax: +49 (0)6063/502-210

Email: contact@maul.de

Website: www.maul.de