Bestier L Shape Gaming Desk
Model: G200610SUS | Version: V001-031925-01
Assembly Instructions
This document provides detailed instructions for assembling your Bestier L Shape Gaming Desk. Please read all instructions carefully before beginning.
General Information & Safety Precautions
Before You Start:
- Inspect product packaging to ensure the appearance is good.
- Read the assembly instructions carefully and follow them step by step.
- To avoid scratching, placing a soft blanket on the floor is suggested.
- Identify, sort, and count all parts with tags.
- Find the installation position according to the drawing and install it in the correct steps.
Other Information:
- ??? People needed for assembly: 1-2.
- ⏱️ Estimated assembly time: 1-1.5 hours.
Caution:
- ⚠️ Be cautious when using a power drill or power screwdriver.
- Please slow down and stop when a screw is nearly tight.
- Do not use any harsh chemicals or abrasive cleaners for this item.
- Push, pull, or drag this item carefully.
Product Details
Dimensions:
- Overall Width: 41.61" / 105.7cm
- Overall Depth: 30.6" / 77.8cm (main desk section)
- Overall Height: 36.4" / 92.5cm
- Desk Surface Height: 29.7" / 75.4cm
- Top Shelf Depth: 7.7" / 19.7cm
- Side Shelf Depth: 10.94" / 27.8cm
Weight Capacities (Approximate):
- Main Desk Surface: 100 LBS / 45 KG
- Side Shelves: 22 LBS / 10 KG each
- Top Shelf: 30 LBS / 14 KG
- Smaller Shelves/Supports: 2.2 LBS / 1 KG each
- CPU Stand (if applicable, based on diagram): 44 LBS / 20 KG
Part List
| Part # | Description | Quantity |
|---|---|---|
| 1 | Main Desk Panel | X1 |
| 2 | Side Desk Panel | X1 |
| 3 | Upper Shelf Panel | X1 |
| 4 | Top Shelf Panel | X1 |
| 5 | Side Support Panel | X1 |
| 6 | Lower Shelf Panel | X1 |
| 7 | Left Leg Frame | X2 |
| 8 | Right Leg Frame | X1 |
| 9 | Back Support Panel | X1 |
| 10 | Monitor Shelf Panel | X1 |
| 11 | Left Frame Connector | X1 |
| 12 | Right Frame Connector | X1 |
| 13 | Upper Back Support | X1 |
| 14 | Upper Side Support | X1 |
| 15 | Desk Support Bracket | X1 |
| 16 | Lower Leg Brace | X2 |
| 17 | Upper Leg Brace | X2 |
| 18 | Cross Brace | X3 |
| 19 | Long Support Bar | X1 |
| 20 | Long Shelf Support | X1 |
| 21 | Short Shelf Support | X2 |
| 22 | Cable Management Tray | X1 |
| 23 | Headset/Accessory Hook Holder | X1 |
| 24 | Accessory Hook | X2 |
| 25 | Mounting Bracket | X2 |
| 26 | Adjustable Foot Pad | X7 |
| 27 | Cup Holder Mount | X2 |
| 28 | Power Strip Holder/Hub | X1 |
| 29 | Power Strip/Hub Unit | X1 |
Accessory List
| Code | Description | Quantity |
|---|---|---|
| A | ST6x35mm Screw | 2 |
| B | Ø15mm Washer | 2 |
| C | Ø8x40mm Screw | 6+2 |
| D | ST5x50mm Screw | 15+1 |
| E | ST7x50mm Screw | 8+1 |
| F | M6x40mm Screw | 2 |
| G | M6x30mm Screw | 20+1 |
| H | M6x25mm Screw | 8+1 |
| I | M6x16mm Screw | 10+1 |
| J | M6x10mm Screw | 6+1 |
| K | M6 Nut | 5+1 |
| L | ST4x14mm Screw | 2 |
| M | M4x8mm Screw | 6+1 |
| N | ST3.5x10mm Screw | 2 |
| O | Ø16mm Washer | 2 |
| P | ST5x40mm Screw | 4+1 |
| (Included Tool) | Allen Wrench | 1 |
| (Included Tool) | Screwdriver | 1 |
Assembly Steps
Step 1: Attach Leg Frames to Main Desk Panel
Parts: Part 7 (Left Leg Frame) x2, Part 1 (Main Desk Panel) x1, Part 16 (Lower Leg Brace) x2, Part 17 (Upper Leg Brace) x2.
Hardware: Part C (Ø8x40mm Screw) x6, Part I (M6x16mm Screw) x3.
Description: Attach the two Left Leg Frames (7) to the underside of the Main Desk Panel (1) using screws C and I. Connect the Lower Leg Braces (16) and Upper Leg Braces (17) between the leg frames.
Step 2: Attach Right Leg Frame and Cross Braces
Parts: Part 8 (Right Leg Frame) x1, Part 18 (Cross Brace) x2.
Hardware: Part E (ST7x50mm Screw) x6, Part G (M6x30mm Screw) x3.
Description: Attach the Right Leg Frame (8) to the Main Desk Panel (1) and connect it to the existing leg structure using Cross Braces (18). Ensure all connections are made with screws E and G.
Step 3: Connect Frame Connectors and Back Support
Parts: Part 11 (Left Frame Connector) x1, Part 7 (Left Leg Frame) x1, Part 16 (Lower Leg Brace) x1.
Hardware: Part J (M6x10mm Screw) x2.
Description: Attach the Left Frame Connector (11) to the Left Leg Frame (7) and Lower Leg Brace (16) using screws J. Ensure the connector is oriented correctly for subsequent steps.
Note: A checkmark ✔️ indicates correct assembly, while a cross ❌ indicates incorrect assembly.
Step 4: Attach Right Frame Connector and Back Support
Parts: Part 12 (Right Frame Connector) x1, Part 7 (Left Leg Frame) x1, Part 18 (Cross Brace) x1.
Hardware: Part J (M6x10mm Screw) x2, Part M (M4x8mm Screw) x2.
Description: Turn the assembly over. Attach the Right Frame Connector (12) to the Left Leg Frame (7) and Cross Brace (18) using screws J and M. Ensure correct orientation.
Instruction: The text "Turn over" ↪️ indicates to flip the unit.
Step 5: Attach Upper Back Support
Parts: Part 13 (Upper Back Support) x1, Part 8 (Right Leg Frame) x1.
Hardware: Part J (M6x10mm Screw) x2.
Description: Attach the Upper Back Support (13) to the Right Leg Frame (8) using screws J.
Step 6: Attach Side Supports and Long Shelf Support
Parts: Part 11 (Left Frame Connector) x1, Part 12 (Right Frame Connector) x1, Part 20 (Long Shelf Support) x1, Part 19 (Long Support Bar) x1.
Hardware: Part G (M6x30mm Screw) x4.
Description: Attach the Left Frame Connector (11) and Right Frame Connector (12) to the main structure. Install the Long Shelf Support (20) and Long Support Bar (19) using screws G. Note: Tighten screws to 80% initially.
Step 7: Attach Upper Shelf Panel and Side Supports
Parts: Part 2 (Side Desk Panel) x1, Part 4 (Top Shelf Panel) x1.
Hardware: Part D (ST5x50mm Screw) x4.
Description: Attach the Side Desk Panel (2) and Top Shelf Panel (4) to the frame using screws D. Ensure correct alignment for the shelf.
Note: The diagram shows a checkmark ✔️ for correct placement and a cross ❌ for incorrect placement.
Step 8: Install Additional Supports and Braces
Parts: Part 7 (Left Leg Frame) x1, Part 11 (Left Frame Connector) x1, Part 27 (Cup Holder Mount) x2.
Hardware: Part G (M6x30mm Screw) x4, Part K (M6 Nut) x4.
Description: Securely attach additional supports and braces to the leg frames and connectors using screws G and nuts K. Install the Cup Holder Mounts (27).
Step 9: Attach Back Panel and Shelf Supports
Parts: Part 1 (Main Desk Panel) x1, Part 20 (Long Shelf Support) x1.
Hardware: Part D (ST5x50mm Screw) x4, Part H (M6x25mm Screw) x3.
Description: Attach the Back Panel (1) and Long Shelf Support (20) to the main desk structure using screws D and H.
Step 10: Flip and Attach Side Panels
Parts: Part 2 (Side Desk Panel) x1, Part 10 (Monitor Shelf Panel) x1.
Hardware: Part P (ST5x40mm Screw) x2.
Description: Turn the assembly over. Attach the Side Desk Panel (2) and Monitor Shelf Panel (10) using screws P.
Instruction: The text "Turn over" ↪️ indicates to flip the unit.
Step 11: Attach Remaining Side Panel and Supports
Parts: Part 2 (Side Desk Panel) x1, Part 9 (Back Support Panel) x1.
Hardware: Part P (ST5x40mm Screw) x2, Part E (ST7x50mm Screw) x2.
Description: Attach the remaining Side Desk Panel (2) and the Back Support Panel (9) using screws P and E.
Step 12: Final Tightening of Screws
Hardware: Part I (M6x16mm Screw) x7.
Description: Fully tighten all screws installed in previous steps. Ensure all connections are secure.
Instruction: The text "Fully tighten all screws" is repeated in multiple languages.
Step 13: Attach Upper Shelf and Side Supports
Parts: Part 6 (Lower Shelf Panel) x1, Part 21 (Short Shelf Support) x2.
Hardware: Part D (ST5x50mm Screw) x2, Part G (M6x30mm Screw) x2.
Description: Attach the Lower Shelf Panel (6) to the Short Shelf Supports (21) using screws D and G. Ensure correct orientation.
Step 14: Attach Upper Side Supports and Shelf
Parts: Part 13 (Upper Back Support) x1, Part 14 (Upper Side Support) x1, Part 6 (Lower Shelf Panel) x1, Part 21 (Short Shelf Support) x2.
Hardware: Part D (ST5x50mm Screw) x2, Part G (M6x30mm Screw) x4.
Description: Attach the Upper Side Supports (14) and Upper Back Support (13) to the frame. Install the Lower Shelf Panel (6) using screws D and G. Ensure correct alignment.
Step 15: Attach Main Desk Panel and Supports
Parts: Part 5 (Side Support Panel) x1, Part 14 (Upper Side Support) x1, Part 21 (Short Shelf Support) x1.
Hardware: Part H (M6x25mm Screw) x3.
Description: Attach the Side Support Panel (5) and Upper Side Support (14) to the main structure using screws H. Ensure all parts are aligned.
Note: This step requires two people ???.
Step 16: Install Cable Management Tray
Parts: Part 26 (Adjustable Foot Pad) x7.
Hardware: None specified for this step, but foot pads are shown.
Description: Install the adjustable foot pads (26) at the bottom of the leg frames. Adjust them to ensure the desk is stable and level.
Step 17: Attach Top Shelf Brackets
Parts: Part 3 (Upper Shelf Panel) x1.
Hardware: Part G (M6x30mm Screw) x1, Part K (M6 Nut) x1.
Description: Attach the Top Shelf Panel (3) using screws G and nuts K. Ensure it is securely fastened.
Note: The diagram shows a checkmark ✔️ for correct attachment and a cross ❌ for incorrect attachment.
Step 18: Attach Monitor Shelf and Back Panel
Parts: Part 3 (Upper Shelf Panel) x1, Part 14 (Upper Side Support) x1, Part 21 (Short Shelf Support) x1.
Hardware: Part H (M6x25mm Screw) x2.
Description: Attach the Monitor Shelf (3) to the Upper Side Support (14) and Short Shelf Support (21) using screws H.
Note: The diagram indicates "Back view" ?.
Step 19: Attach Top Shelf and Supports
Parts: Part 3 (Upper Shelf Panel) x1.
Hardware: Part D (ST5x50mm Screw) x3.
Description: Attach the Top Shelf Panel (3) to the desk structure using screws D. Ensure it is fully secured.
Note: The diagram indicates "100% tighten" ✔️.
Step 20: Install Cable Management Tray
Parts: Part 22 (Cable Management Tray) x1, Part 29 (Power Strip/Hub Unit) x1.
Hardware: Part M (M4x8mm Screw) x2.
Description: Attach the Cable Management Tray (22) to the underside of the desk. Connect the Power Strip/Hub Unit (29) to the tray using screws M. Ensure the cables are routed correctly.
Note: The diagram shows a checkmark ✔️ for correct connection and a cross ❌ for incorrect connection.
Step 21: Attach Monitor Shelf Supports
Parts: Part 11 (Left Frame Connector) x1, Part 12 (Right Frame Connector) x1.
Hardware: Part G (M6x30mm Screw) x2.
Description: Attach the Left Frame Connector (11) and Right Frame Connector (12) to the monitor shelf supports using screws G.
Step 22: Attach Top Shelf to Supports
Parts: Part 4 (Top Shelf Panel) x1.
Hardware: Part A (ST6x35mm Screw) x2.
Description: Attach the Top Shelf Panel (4) to the frame supports using screws A. Ensure it is level and secure.
Step 23: Attach Upper Shelf and Brackets
Parts: Part 4 (Top Shelf Panel) x1, Part 10 (Monitor Shelf Panel) x1.
Hardware: Part B (Ø15mm Washer) x2, Part F (M6x40mm Screw) x2, Part O (Ø16mm Washer) x2.
Description: Attach the Top Shelf Panel (4) and Monitor Shelf Panel (10) using screws F and washers B and O. Ensure correct orientation.
Note: The diagram indicates "Back view" ?.
Step 24: Attach Side Supports and Shelf
Parts: Part 3 (Upper Shelf Panel) x1.
Hardware: Part L (ST4x14mm Screw) x2.
Description: Attach the Upper Shelf Panel (3) to the side supports using screws L. Ensure it is securely fastened.
Note: The diagram indicates "Back view" ?.
Step 25: Attach Accessory Holder
Parts: Part 23 (Headset/Accessory Hook Holder) x1.
Hardware: Part N (ST3.5x10mm Screw) x2.
Description: Attach the Headset/Accessory Hook Holder (23) to the desk frame using screws N.
Note: The diagram indicates "Back view" ?.
Step 26: Final Assembly Check
Description: Ensure all screws are fully tightened. Check the stability of the desk. Adjust the foot pads (26) as needed to level the desk.
Instruction: The text "Fully tighten all screws" is repeated in multiple languages.
Customer Support
For assistance, please contact Bestier customer support:
| Region | Contact |
|---|---|
| North American | 888-666-1086 Service@bestier.net |
| Europe | Service.UK@bestier.net Service.FR@bestier.net Service.ES@bestier.net |
| Asia | Service.DE@bestier.net Service.IT@bestier.net 04-8888-0283 Service.JP@bestier.net |
| Global | Service@bestier.net |
Made in China.
