Bestier Multifunctional Computer Desk
Model: D505R
Helpful Hints
Before You Start
- Inspect product packaging to ensure the appearance is good.
- Read the assembly instructions carefully and follow them step by step.
- To avoid any scratching, putting a soft blanket on the floor is suggested.
- Identify, sort, and count all the parts with tags.
- Find out the installation position according to the drawing and install it in correct steps.
Other
- People needed for assembly: 1-2.
- Estimated assembly time: 0.5-1 hour.
Caution
- Be cautious when using a power drill or power screwdriver.
- Please be aware to slow down and stop when the screw is nearly tight.
- Do not use any harsh chemicals or abrasive cleaners for this item.
- Push, pull, or drag this item carefully.
Part List
The following parts are included in the package:
- Part 1: Desktop Panel (x1)
- Part 2: Desktop Panel (x1)
- Part 3: Desktop Panel (x1)
- Part 4: Shelf Panel (x2)
- Part 5: Shelf Panel (x2)
- Part 6: Metal Frame (x1)
- Part 7: Metal Frame (x2)
- Part 8: Metal Frame (x2)
- Part 9: Metal Rod (x1)
- Part 10: Metal Rod (x1)
- Part 11: Metal Rod (x2)
- Part 12: Metal Rod (x5)
- Part 13: Metal Rod (x8)
- Part 14: Metal Rod (x4)
- Part 15: Metal Frame Component (x4)
- Part 16: Long Metal Rod (x1)
- Part 17: Short Metal Rod (x1)
- Part 18: Metal Rod (x1)
- Part 19: Metal Rod (x1)
- Part 20: Shelf Panel (x1)
- Part 21: Shelf Panel (x1)
- Part 22: Drawer/Tray Component (x1)
- Part 23: Support Bracket (x1)
- Part 24: Support Bracket (x1)
- Part 25: Light Strip and Controller (x1)
- Part 26: Fabric Holder (x1)
- Part 27: Cable Management Clip (x2)
Accessory List
The following accessories are included:
- A: M6x12mm Screws (x2)
- B: M6x28mm Screws (81+3)
- C: Ø8mm Washers (8+1)
- D: M6x19mm Screws (8+1)
- E: Ø60mm Caps (x3)
- F: M6 Screws (14+1)
- G: Ø6-Ø17 Washers (8+1)
- H: ST4x14mm Screws (12+1)
- Tools: Allen Wrench, Screwdriver (provided)
Assembly Instructions
Follow the numbered steps below to assemble your Bestier Multifunctional Computer Desk.
Step 1
Attach part 16 to part 15 using screws B. Repeat for the other side with part 16 and part 15.
Step 2
Connect the assembled frames from Step 1. Attach part 21 to the top of the frames using screws B and washers G. Attach part 17 to the side of the frames using screws B and washers G. Repeat for the other side.
Step 3
Attach part 1 to the front of the assembled structure using screws H. Ensure the 'Front' label is visible.
Step 4
Attach part 5 to the side of the structure using screws D. Repeat for the other side.
Step 5
Assemble the left side of the desk. Attach part 7 to part 12 using screws B (80% tighten). Attach part 14 to part 7 using screws B (80% tighten). Repeat for the other side.
Step 6
Assemble the right side of the desk. Attach part 4 to part 8 using screws B (80% tighten). Attach part 8 to part 7 using screws B (80% tighten). Repeat for the other side.
Step 7
Connect the two sides of the desk. Attach part 11 to the top of the frames using screws B.
Step 8
Attach part 13 to the back of the desk structure using screws F and A. Use the provided wrench for tightening.
Step 9
Continue assembling the desk structure. Attach part 7 to part 10 using screws B (80% tighten). Attach part 9 to part 8 using screws B (80% tighten). Attach part 11 to part 7 using screws B (80% tighten). Attach part 6 to part 9 using screws B (80% tighten).
Step 10
Complete the main desk structure. Attach part 10 to part 9 using screws B (100% tighten). Attach part 12 to part 6 using screws B (100% tighten).
Step 11
Attach the remaining shelves and support structures. Connect part 13 to the frames using screws F and A. Use the provided wrench for tightening.
Step 12
Continue reinforcing the desk structure. Attach part 18 to the frames using screws B (90% tighten).
Step 13
Attach the fabric holders (part 26) to the desk frame using screws B and F. Secure them with screws B and F.
Step 14
Attach the desktop panels. Attach part 2 to the main structure using screws B (80% tighten). Attach part 11 to the structure using screws B (80% tighten). Attach part 7 and 8 to the structure using screws B (80% tighten).
Step 15
Continue attaching desktop panels and supports. Attach part 2 to the main structure using screws B (80% tighten). Attach part 3 to the structure using screws B (80% tighten). Attach part 7 and 8 to the structure using screws B (80% tighten).
Step 16
Finalize the main desk structure. Attach part 1 to the top of the desk using screws B (100% tighten). Ensure all connections are secure.
Step 17
Install the drawer/tray component (part 22). Slide part 22 into the designated slots and secure it with screws H.
Step 18
If the laminate is not flat, paste the C pad (washer) to the uneven surface. Repeat for any other uneven laminate surfaces.
Step 19
Attach the additional shelf units (parts 20 and 21) to the top of the desk.
Step 20
Connect the LED light strip (part 25) to the controller and plug it into a 5V USB power source. The arrow on the connector should point towards the front of the controller.
Customer Support
For assistance, please contact Bestier Customer Support:
- North America: 888-666-1086, Service.US@bestier.net
- Europe: Service.UK@bestier.net, Service.FR@bestier.net, Service.ES@bestier.net
- Asia: Service.DE@bestier.net, 488-880-283, Service.IT@bestier.net, Service.JP@bestier.net
- Global: Service@bestier.net
- China Domestic: 0755-26917626, sskj@bestier.net
Bestier, Love coming home.
Comfort Zone Co., Limited
RM1903 19F BeiYou technology Building, Yuehai Street, No.42 Gaoxin South Ring Road, Nanshan, Shenzhen
Made in China
