SuperATV Installation Instructions

Inner Fender Guard: for CFMOTO ZFORCE 950 Sport

2753 Michigan Road • Madison, Indiana 47250 • 855-743-3427

Do not discard packaging until product has been successfully installed.

Parts Included

Installation Instructions

Step 1: Prepare the Vehicle

On the right side of the vehicle, locate and remove the plastic rivets shown in the illustration. On the same side, locate and remove the indicated bolt.

Step 2: Install Right Template

Attach the 'Right Template' to the vehicle's plastic fender using the previously removed plastic rivets. Mark the hole locations onto the plastic. Before drilling, check behind the plastic for any potential interference. Remove the 'Right Template' and drill holes through the plastic; the holes should be Ø3/8".

Step 3: Install Clamp

Install the clamp around the vehicle's frame. The clamp should be snug but not tight.

Step 4: Attach Right Bracket to Clamp

Install the 'Right Bracket' to the clamp using the provided hardware. The hardware should be snug but not tight. The required hardware is an M8 x 12mm bolt.

Step 5: Secure Plastic and Bracket

Reinstall the stock screw. Secure the vehicle's plastic fender to the 'Right Bracket' using the provided hardware (2x M6 x 20mm). Tighten hardware until snug. Remove any temporary hardware, pull back the plastic fender slightly, and tighten the 'Right Bracket' and clamp hardware.

Step 6: Mount the Right Guard

Install the 'Right Guard' and secure it to the 'Right Bracket' using the provided hardware (2x M6 x 20mm). Tighten hardware. Use the provided drill bit to drill a hole into the vehicle's frame. Secure the 'Right Guard' to this frame location using the M6 x 20mm (Thread Forming) hardware. Tighten hardware.

Step 7: Install Left Side

Repeat all previous steps for the driver's (left) side installation.

Liability Statement

SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.

Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.

By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.

SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified.

Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.

The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.

Need help with your installation?

Email: sales@superatv.com

Website: www.superatv.com

Phone: ? 1-855-743-3427

Hours: ⏰ 8:00am - 8:00pm EST M-Th | 8:00am - 7:00pm EST Friday | 9:00am - 2:00pm EST Saturday

© 2021 SuperATV.com®. All Rights Reserved.

Models: FAP-CF-ZF950 Inner Fender Guard, FAP-CF-ZF950, Inner Fender Guard, Fender Guard, Guard

File Info : application/pdf, 9 Pages, 1.05MB

PDF preview unavailable. Download the PDF instead.

FAP-CF-ZF950 ?t=1667628324&

References

Adobe PDF Library 10.0.1 Adobe InDesign CS6 (Windows)

Related Documents

Preview SuperATV Glass Windshield Installation Instructions for CFMOTO ZFORCE 950 Sport
Step-by-step installation guide for the SuperATV Glass Windshield designed for the CFMOTO ZFORCE 950 Sport. Includes parts list, assembly instructions, and important liability information.
Preview SuperATV Glass Windshield Installation Guide for CFMOTO UFORCE 1000
Step-by-step installation instructions for the SuperATV Glass Windshield designed for the CFMOTO UFORCE 1000. Includes parts list, warnings, liability information, and contact details.
Preview SuperATV Game Loader Rack Installation Instructions for CFMOTO UFORCE 1000
Detailed installation guide for the SuperATV Game Loader Rack, designed for the CFMOTO UFORCE 1000. Includes parts list, step-by-step assembly, wiring, safety precautions, and operating tips for the integrated winch.
Preview SuperATV Rear Brush Guard Installation Instructions for Can-Am Maverick Trail
Detailed installation guide for the SuperATV Rear Brush Guard designed for the Can-Am Maverick Trail. Includes step-by-step instructions, liability information, and contact details.
Preview SuperATV Front Brush Guard Installation Instructions for Polaris Ranger XP 1000
Detailed installation guide for the SuperATV Front Brush Guard (FBG-P-RAN1K) designed for the Polaris Ranger XP 1000. Includes parts list, hardware specifications, and step-by-step instructions for mounting and assembly.
Preview SuperATV Plug and Play Turn Signal Kit Installation Instructions for CFMOTO UFOCE 1000
Detailed installation instructions for the SuperATV Plug and Play Turn Signal Kit designed for the CFMOTO UFOCE 1000. This guide covers component identification, wiring, and step-by-step assembly for a complete installation.
Preview SuperATV Power Flip Windshield Installation Instructions for Polaris Ranger 1000
Detailed installation guide for the SuperATV Power Flip Windshield for Polaris Ranger 1000, including parts list, electrical wiring, and step-by-step assembly instructions.
Preview SuperATV Flip Windshield Installation Instructions for Can-Am Commander
Comprehensive installation guide for the SuperATV Flip Windshield, compatible with Can-Am Commander models. This document details the kit contents, hardware, step-by-step assembly procedures, and cleaning recommendations. Ensure proper installation for optimal performance and safety.