Stand-up Desktop Computer Desk

Assembly and Safety Information

Please read this manual carefully before starting the installation and assembly of this product. If you have any questions or ambiguities regarding the instructions and warnings, please contact customer support.

Important Notes:

• Do not exceed the rated load capacity to avoid damage to the monitor or personal injury.
• Ensure installation follows the manual's instructions to prevent product damage or personal injury.
• Use only the provided tools and accessories for installation to prevent product damage.
• Verify that the support surface can safely bear the weight of the equipment and all accessories.
• This product contains small parts that could cause serious injury if swallowed. Keep out of reach of children.
• Do not install the monitor before assembling the workbench.
• Do not open or replace any part of the workbench without authorization.
• This product is intended for indoor use only. Outdoor use may cause product damage.

Important Pre-Assembly Check:

Before installation, ensure all parts are present according to the provided list. If any parts are missing or damaged, please contact your supplier.

Maintenance:

Periodically check the workbench (at least every three months) to ensure stability. Tighten any loose screws due to long-term use. Address any safety hazards by replacing accessories or reinforcing the installation.

Weight Capacity: 17kg (37lbs)

Caution: Do not press hard on the front edge of the countertop or climb on the desk. Be mindful of your hands during assembly.

Parts List

The following parts are included in the package:

1. Desktop (1000x400) x1
2. Desktop (890x500) x1
3. Support Bar (896x97) x1
4. Support Bar (896x126) x1
5. Desktop (500x300) x1
6. Frame Component x1
7. Frame Component x1
8. Frame Component x1
9. Frame Component x1
10. Mesh Shelf (946x396) x2
11. Mesh Shelf (496x246) x2
12. Support Bracket (with pre-drilled holes) x1
13. Long Support Bar (25x25x946) x1
14. Medium Support Bar (25x25x896) x1
15. Long Support Bar (25x25x896) x1
16. Long Support Bar (25x25x896) x1
17. Lift Mechanism x1
18. Lift Mechanism x1
19. Long Bar (20x40x876) x1
20. Bar (20x30x896) x1
21. Short Bar (25x25x246) x2
22. Long Bar (20x30x896) x1
23. Screw (M8) x8
24. Screw (M6x45) x30
25. Screw (M6x40) x7
26. Screw (M6x35) x10
27. Screw (M6x25) x4
28. Screw (M6x12) x20
29. Screw (M5x60) x8
30. Nut (M6) x7

Assembly Steps

Follow these steps to assemble your stand-up desktop computer desk:

Step (1): Assemble the main frame components (6, 7, 8, 9) using screws (23).

Step (2): Attach the support bar (13) and mesh shelves (10) to the assembled frame. Ensure correct orientation as indicated by arrows labeled 'A'.

Step (3): Construct the base structure, integrating the mesh shelves.

Step (4): Attach the desktop components (3, 15, 16) using screws (F).

Step (5): Connect the main frame (Figure (1)-7) to the desk structure using screws (G) and (B), and attach the support bar (22) using screws (F).

Step (6): Continue assembling the frame, ensuring all connections are secure.

Step (7): Attach the remaining mesh shelves (11) and support bars (21) to the frame, aligning with arrows labeled 'A'.

Step (8): Install the lift mechanisms (17, 18) onto the desk frame using screws (E) x6.

Step (9): Continue installing the lift mechanisms (17, 18) onto the desk frame using screws (E) x6.

Step (10): Attach the long bar (19) to the assembled structure.

Step (11): Secure the lift mechanism components using screws (D).

Step (12): Attach the first desktop component (1) to the lift mechanism using screws (E) x4.

Step (13): Attach the second desktop component (2) to the lift mechanism using screws (C).

Step (14): Attach the final desktop component (5) to the lift mechanism.