Digital Watchdog MEGApix IVA+™ and IVA™ Quick Start Guide

Model Numbers: DWC-MPB48WiATW, DWC-MB48WiATW

Download Support Materials

To download all support materials and tools, visit:

http://www.digital-watchdog.com/resources

Search for your product by entering the part number in the 'Search by Product' bar. Applicable materials, including manuals and quick start guides (QSGs), will appear.

This document serves as a quick reference for initial setup. For complete installation and usage, please refer to the full instruction manual.

These instructions are intended to ensure correct product usage and prevent danger or property loss.

Safety and Warning Information

Warnings: Serious injury or death may occur if warnings are neglected.

Cautions: Injury or equipment damage may occur if cautions are neglected.

Warnings

Comply with national and regional electrical safety regulations. Ensure wall/ceiling mounted devices are firmly fixed.
Use only the specified standard adapter. Using other adapters may cause fire, electric shock, or product damage.
Verify the power supply voltage is correct before use.
Incorrect power connection or battery replacement may cause explosion, fire, electric shock, or product damage.
Do not connect multiple cameras to a single adapter; this can cause excessive heat generation or fire.
Securely plug the power cord into the power source to prevent fire.
Fasten the camera securely during installation to prevent personal injury from falling.
Avoid installation in locations with elevated temperature, low temperature, or high humidity to prevent fire or electric shock.
Do not place conductive objects (e.g., screwdrivers, coins, metal items) or water-filled containers on the camera to prevent injury from fire, electric shock, or falling objects.
Do not install in humid, dusty, or sooty locations to prevent fire or electric shock.
Avoid installation near heat sources like radiators, heat registers, or other heat-producing products.
Keep away from direct sunlight and heat radiation sources to prevent fire.
If unusual smells or smoke occur, stop use immediately, disconnect power, and contact a service center.
If the product does not operate normally, contact a service center. Do not disassemble or modify the product.
When cleaning, do not spray water directly onto the product to prevent fire or electric shock.

Cautions

Use proper safety gear during installation and wiring.
Do not drop objects on the product or apply strong shock. Keep away from excessive vibration or magnetic interference.
Do not use the product near water.
The product should not be exposed to dripping or splashing; do not place liquid-filled objects on it.
Avoid aiming the camera directly at extremely bright objects like the sun, as this may damage the image sensor.
The main plug serves as the disconnect device and must remain readily operable.
Remove the power adapter during lightning to prevent fire or product damage.
Do not block ventilation openings. Install according to manufacturer instructions.
A polarized or grounding-type plug is recommended. Consult an electrician if the provided plug does not fit your outlet.
Protect the power cord from being walked on or pinched, especially at plugs and where it exits the product.
If laser equipment is used nearby, ensure the sensor surface is not exposed to laser beams, which can damage the sensor module.
Turn off power before moving or reinstalling an installed product.
Proper configuration of passwords and security settings is the installer's/end-user's responsibility.
For cleaning, use a clean, soft cloth. Cover the lens cap when not in use to protect from dirt.
Do not touch the camera's lens or sensor module with fingers.
Use only manufacturer-specified attachments/accessories.
Always use hardware (screws, anchors, bolts, etc.) compatible with the mounting surface and of sufficient strength for a secure mount.
Use only with manufacturer-specified carts, stands, tripods, brackets, or tables.
Unplug the product when using a cart. Use caution when moving cart/product combinations to avoid tip-over injuries.
Refer all servicing to qualified personnel. Servicing is needed for damage, liquid spills, objects falling into the product, exposure to rain/moisture, abnormal operation, or drops.

Installation Steps

STEP 1 – Preparing to Mount the Camera

Note: These instructions are for qualified service personnel only. Do not perform internal work unless qualified.

This product requires a UL Listed Power Supply Unit rated 12 Vdc, 1.1A min or PoE (802.3at) 0.37A min.

PoE power must be supplied by a UL Listed device compliant with IEEE 802.3at, evaluated as a Limited Power Source (UL60950-1 or UL62368-1).

The unit is intended for installation in Network Environment 0 (IEC TR 62102), meaning Ethernet wiring should be limited to inside the building.

Remove the sun-shield cover as needed for installation.

Moisture Packet Installation

Install the moisture packet in the camera's external control panel:

Remove the Desi-Pack moisture absorber from packaging.
Open the side cover to access the external camera control panel.
Place the moisture absorber under the camera’s SD card slot.

Note: The camera generates heat to dry moisture during operation. Keep the absorber in place if moisture issues are possible. It has an approximate 6-month life cycle.

Warning: Install the moisture absorber to prevent moisture buildup, which can cause image performance issues and damage the camera.

Using the mounting template or the camera, mark and drill necessary holes in the wall or ceiling.

Resetting the Camera

Press the reset button on the external control panel for five (5) seconds to reset all settings, including network settings.

Diagram Description: The external control panel includes a Reset Button.

STEP 2 – Powering the Camera

Pass wires through and make necessary connections.

Connections:

PoE Switch or Injector: Use an Ethernet cable for both data and power.
Non-PoE Switch: Use an Ethernet cable for data and a power adapter for power.

Power Requirements and Consumption

Power Requirements: DC12V, IEEE 802.3at PoE+ class 4 (Adapter not included)

Power Consumption: DC12V: 10.2W, PoE: 16W

Note: A PoE injector is required and sold separately.

Waterproof Cap and Cable Connection

The waterproof cap set includes two rubber rings. Use the ring best suited for your network cable's diameter:

Note: Ensure the o-ring is in place between components 'a' and 'b' for a moisture seal. Outdoor-rated sealer is recommended for extreme environments.

Connection Steps:

Pass the LAN cable through the waterproof cap, gasket, and the appropriate rubber ring ('a').
Connect the LAN cable to the camera’s network port ('b').
Affix component 'c' to 'b' with a quarter turn counter-clockwise.
Thread and twist component 'd' tightly to 'c'.

Note: Cables with 4.5mm to 5.5mm diameter should use the black rubber ring. Cables over 5.5mm should use the white rubber ring.

Note: To prevent cables from getting caught between the camera and mounting surface (which can cause damage and prevent flush mounting), remove the rubber plug on the camera's bracket side and use the gap as a cable guide, depending on the installation environment.

Mounting Components

Diagram Description: Key mounting components visible include: Mounting template, SD card slot, Pan/Tilt Screw, Reset button, Test video output port.

STEP 6 – DW® IP Finder™

The DW IP Finder software scans the network to detect MEGApix® cameras, configure network settings, and access the camera's web client.

Software Installation:

Go to: http://www.digital-watchdog.com
Search for "DW IP Finder" in the top search box.
Navigate to the "Software" tab on the DW IP Finder page to download and install the software.
Open DW IP Finder and click 'Scan Devices' to scan the selected network. Results will appear in a table. The DW® logo turns gray during the scan.

Initial Password Setup:

A password must be set when connecting to the camera for the first time.

Select the camera(s) in the IP Finder search results by checking the box next to them.
Click "Bulk Password Assign" on the left side.
Enter the current username and password (default: admin/admin).
Enter a new username and password. Passwords must be at least 8 characters with a mix of uppercase, lowercase, numbers, and special characters. Passwords cannot contain the user ID.
Click "change" to apply the new password(s).

Configuring Camera Settings:

Double-click a camera's image or click the 'Click' button under the 'IP Conf.' column to open its current network settings.
Adjust settings as needed.
To access the camera's web page, click 'View Camera Website' from the IP Config window.
To save changes, enter the camera's admin username and password and click 'Apply'.

Network Configuration:

Default TCP/IP: DHCP. This allows the camera to receive an IP address automatically from the DHCP server.

Static IP: Select "Static" to manually enter the IP address, (Sub)Netmask, Gateway, and DNS information. The camera's IP must be static when connecting to Spectrum® IPVMS. Consult your network administrator for details.

Note: Port forwarding must be configured on your network router to access the camera from an external network.

STEP 7 – Web Viewer

Note: GUI display may vary by camera model. Some menu options may not be available depending on the camera model.

Note: Chrome browser is recommended for IVA configuration.

Locate the camera using DW IP Finder.
Double-click the camera's view in the results table.
Press 'View Camera Website'. The camera's web viewer will open in your default web browser.
Enter the username and password set up in DW IP Finder. If a new password was not set, you will be prompted to set one to view video.
When accessing the camera for the first time, install the VLC player for web files to view video.

Note: A 32-bit version of VLC player is required. If using a 64-bit system, uninstall the 64-bit version and install the 32-bit version.

What's in the Box

Star Wrench (T-10)
Star Wrench (T-20)
Test Monitor Cable
Screws and Plastic Anchors (4pcs)
Moisture Absorber and Installation Guide (Recommended)
Waterproof Cap and Rubber Rings (Black: ø4mm, White: ø5mm)
PoE injector and power cable (optional)
Quick Setup and Download Guides
Mounting template

Contact Information

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours: 9:00 AM – 8:00 PM EST, Monday through Friday

Website: digital-watchdog.com

	Digital Watchdog MEGApix Camera Quick Start Guide Quick start guide for installing and setting up Digital Watchdog MEGApix IVA+ and IVA cameras, including model numbers DWC-MPVC8WiATW, DWC-MPVC8Wi28TW, DWC-MVC8WiATW, and DWC-MVC8Wi28TW. Covers safety, mounting, cabling, power, SD card management, and network setup using DW IP Finder.
	Digital Watchdog MEGApix IP Camera Quick Start Guide Concise guide for installing and setting up Digital Watchdog MEGApix IVA+™ IP cameras, covering mounting, cabling, power, software configuration, and web viewer access.
	Digital Watchdog DWC-XSBE05 Series Quick Start Guide A quick start guide for installing and setting up Digital Watchdog DWC-XSBE05 series IP cameras, including safety precautions, connection diagrams, and initial configuration steps.
	Digital Watchdog MEGApix DWC-MB62DiVT IP Camera Quick Start Guide Concise guide for installing and setting up the Digital Watchdog MEGApix DWC-MB62DiVT IP camera, covering unboxing, mounting, powering, network configuration with DW IP Finder, and web viewer access.
	Digital Watchdog DWC-VSTB04Mi Quick Start Guide and Installation Instructions This guide provides essential information for the initial setup and installation of the Digital Watchdog MEGApix DWC-VSTB04Mi IP camera. It covers safety warnings, step-by-step installation, network configuration using DW IP Finder, and accessing the web viewer.
	Digital Watchdog MEGAPIX FLEX IP Camera Quick Start Guide Concise guide for installing and setting up the Digital Watchdog MEGAPIX FLEX configurable multi-sensor IP camera, covering mounting, powering, cabling, and software configuration.
	Digital Watchdog DWC-MV95WIATW MEGApix 5MP Vandal Dome IP Camera User Manual Comprehensive user manual for the Digital Watchdog DWC-MV95WIATW 5MP Vandal Dome IP Camera. Covers installation, network setup, configuration, live view, security, and troubleshooting. Features include motion detection, line crossing, and remote access.
	Digital Watchdog MEGApix Camera Quick Start Guide A quick start guide for setting up and installing Digital Watchdog MEGApix cameras, including network configuration, web viewer access, and mounting instructions.