Digital Watchdog MEGApix Camera Quick Start Guide

Important Information

This document is a quick reference for initial setup. For complete installation and usage, refer to the full instruction manual.

Resource Download: Visit http://www.digital-watchdog.com/resources and search by part number to find all supported materials.

Safety Precautions:

• Warnings: Neglecting warnings may lead to serious injury or death.
• Cautions: Neglecting cautions may lead to injury or equipment damage.

General Warnings:

• Comply with electrical safety regulations. Ensure the device is securely fixed when wall or ceiling mounted.
• Use only the specified adapter. Incorrect adapters can cause fire, electric shock, or product damage.
• Verify power supply voltage before use.
• Improper power connection or battery replacement may cause explosion, fire, electric shock, or damage.
• Do not connect multiple cameras to a single adapter to prevent overheating or fire.
• Ensure the power cord is securely plugged in to prevent fire hazards.
• Fasten the camera securely to prevent personal injury from falling.
• Avoid installation in locations with high/low temperatures or high humidity to prevent fire or electric shock.
• Do not place conductive objects or water containers on the camera to avoid injury from fire, electric shock, or falling objects.
• Avoid installation in humid, dusty, or sooty locations.
• Do not install near heat sources like radiators or amplifiers.
• Keep away from direct sunlight and heat radiation sources.
• If unusual smells or smoke occur, immediately disconnect power and contact a service center.
• Contact a service center for abnormal operation; do not disassemble or modify the product.
• Do not spray water directly onto the product during cleaning.

General Cautions:

• Use proper safety gear during installation and wiring.
• Do not drop objects on or apply strong shock to the product. Keep away from excessive vibration or magnetic interference.
• Do not use the product near water.
• The product should not be exposed to dripping or splashing.
• Avoid aiming the camera directly at extremely bright objects like the sun to prevent image sensor damage.
• The main plug serves as a disconnect device and must remain operable.
• Unplug the product during lightning to prevent fire or damage.
• Do not block ventilation openings; install according to manufacturer instructions.
• A polarized or grounding-type plug is recommended. Consult an electrician if the plug does not fit the outlet.
• Protect the power cord from being walked on or pinched.
• If laser equipment is used nearby, ensure the sensor surface is not exposed to the laser beam.
• Turn off power before moving or reinstalling an installed product.
• Proper configuration of passwords and security settings is the responsibility of the installer/end-user.
• Use a clean cloth for cleaning. Cover the lens cap when not in use for extended periods.
• Do not touch the camera lens or sensor module with fingers.
• Use only manufacturer-specified attachments/accessories.
• Use compatible hardware for secure mounting.
• Use only with specified carts, stands, tripods, brackets, or tables.
• Unplug the product when using a cart and exercise caution when moving to prevent tip-over injuries.
• Refer all servicing to qualified personnel for any product damage, abnormal operation, or exposure to rain/moisture.

Step 1 – Preparing to Mount the Camera

Use the mounting template or the camera itself to mark and drill holes in the wall or ceiling.

Step 2 – Powering the Camera

Power Requirements: DC12V, PoE (IEEE 802.3af class 2). Adapter not included.

Power Consumption: <5W

Step 3 – Installing the Camera

1. Mount the camera to the surface using the included screws and anchors.
2. Adjust pan and tilt by loosening the lock screw at the base, then tighten once adjusted.
3. Resetting the camera: Press and hold the reset button at the base for five (5) seconds to reset all settings, including network settings.

Step 4 – Cabling

Connect power, network, alarm input/outputs, and audio using the diagram provided. Options include:

• PoE Switch or Injector: Connect data and power with a single Ethernet cable.
• Non-PoE Switch: Connect data via Ethernet cable and power using a power adapter.

Install the waterproof cap if needed. Use outdoor-rated sealer in extreme environments.

Step 5 – Managing the SD Card (Optional)

1. Loosen the fixed screw at the camera base to rotate the camera module. Remove the control panel cover to access the SD card slot.
2. Insert a Class 10 SD/SDHC/SDXC card (max 256GB) into the slot.
3. Press the card inward until it clicks to release it.

Step 6 – DW® IP Finder™

Use the DW® IP Finder™ software to scan the network, detect MEGApix® cameras, configure network settings, or access the camera's web client.

Installation:

1. Go to http://www.digital-watchdog.com.
2. Search for "DW IP Finder" at the top.
3. Navigate to the "Software" tab to download and install.
4. Open DW IP Finder and click 'Scan Devices'. The DW® logo turns gray during the scan.

Initial Password Setup:

1. Check the box next to the camera(s) in the search results.
2. Click "Bulk Password Assign".
3. Enter current username/password (admin/admin). Enter a new username and password (minimum 8 characters, with at least 4 combinations of uppercase/lowercase letters, numbers, and special characters; cannot contain the user ID).
4. Click "change" to apply.

Accessing Camera Settings:

1. Double-click the camera's name or click 'Click' in the results table.
2. The pop-up window shows current network settings. Admin users can adjust as needed. Cameras default to DHCP.
3. Click the 'Website' button to access the camera's web page.
4. Save changes by entering the admin username/password and clicking 'Apply'.

Network Configuration:

• DHCP: Camera automatically receives an IP address from the DHCP server.
• Static: Manually enter IP address, Subnetmask, Gateway, and DNS information. Static IP is required for Spectrum® IPVMS. Contact your network administrator for details.

External Network Access: Port forwarding must be configured on your network's router.

Note: GUI display may vary by camera model. Some menu options may not be available. Refer to the full manual.

Step 7 – Web Viewer

Access the camera's web interface through your browser.

1. Find the camera using DW IP Finder.
2. Double-click the camera's view in the results table and press the 'Website' button.
3. Enter the username and password set during the DW IP Finder setup. If no new password was set, you will be prompted to create one.

Alternative Access:

1. Open a web browser.
2. Enter the camera's IP address and port (e.g., http://<ipaddress>:<port>). Port forwarding may be necessary for access from different networks.
3. Enter the camera's username and password.

What's in the Box

• Quick Setup and Installation Guides: 1 set
• Mounting Template: 1
• Waterproof Cap: 1 set
• Hexagonal Wrench (2mm): 1
• Tapping Screws: 3pcs
• Plastic Plugs: 3pcs
• Rubber Plug: 1

Default Login Information

Username: admin | Password: admin

You will be prompted to set a new password upon first login, either via DW® IP Finder™ or the camera's browser menu.

HEVC Patents

This product is covered by one or more claims of the HEVC Patents listed at patentlist.accessadvance.com.