Digital Watchdog MEGApix DWC-VSTB04Mi Quick Start Guide

Getting Support Materials

Download all support materials and tools from:

http://www.digital-watchdog.com/resources

Search for your product by part number to find manuals and quick start guides.

Important Information

This document is a quick reference for initial setup. For complete installation and usage, refer to the full instruction manual.

Warnings: Serious injury or death may occur if warnings are neglected.

Cautions: Injury or equipment damage may occur if cautions are neglected.

SAFETY AND WARNING INFORMATION

WARNINGS

• Comply with national and regional electrical safety regulations. Ensure the device is firmly fixed when mounted.
• Use only the specified standard adapter to prevent fire, electric shock, or product damage.
• Verify the power supply voltage before use.
• Incorrect power connection or battery replacement can cause explosion, fire, electric shock, or damage.
• Do not connect multiple cameras to a single adapter to avoid excessive heat generation or fire.
• Securely plug the power cord into the power source to prevent fire.
• Fasten the camera securely during installation to prevent personal injury from falling.
• Avoid installation in locations with extreme temperatures or high humidity, which can cause fire or electric shock.
• Do not place conductive objects or water containers on the camera to prevent injury or electric shock.
• Avoid humid, dusty, or sooty locations to prevent fire or electric shock.
• Do not install near heat sources like radiators or amplifiers.
• Keep away from direct sunlight and heat radiation sources to prevent fire.
• If unusual smells or smoke occur, immediately disconnect power and contact a service center.
• If the product does not operate normally, contact a service center. Do not disassemble or modify the product.
• Do not spray water directly onto the product during cleaning to prevent fire or electric shock.

CAUTIONS

• Use proper safety gear during installation and wiring.
• Avoid dropping objects or applying strong shock. Keep away from excessive vibration or magnetic interference.
• Do not use the product near water.
• The product should not be exposed to dripping or splashing. Do not place liquid-filled objects on the product.
• Avoid aiming the camera directly at extremely bright objects like the sun, as it may damage the image sensor.
• The main plug serves as a disconnect device and must remain operable.
• Unplug the power adapter during lightning to prevent fire or damage.
• Do not block ventilation openings. Install according to manufacturer instructions.
• A polarized or grounding-type plug is recommended. Consult an electrician if the plug does not fit the outlet.
• Protect the power cord from being walked on or pinched, especially at plugs and connection points.
• If laser equipment is used nearby, ensure the sensor surface is not exposed to laser beams to prevent sensor damage.
• Turn off power before moving or reinstalling the camera.
• Proper configuration of passwords and security settings is the responsibility of the installer/end-user.
• For cleaning, use a soft, clean cloth. Cover the lens cap when not in use to protect from dirt.
• Do not touch the camera lens or sensor module with fingers.
• Use only manufacturer-specified attachments/accessories.
• Use compatible hardware (screws, anchors, bolts) of sufficient length and construction for secure mounting.
• Use only with manufacturer-specified carts, stands, tripods, brackets, or tables.
• Unplug the product when using a cart. Exercise caution when moving cart/product combinations to prevent tip-over injuries.
• Refer all servicing to qualified personnel when the product is damaged, exposed to liquid/objects, rain/moisture, operates abnormally, or has been dropped.

Installation Steps

STEP 1 – PREPARING TO MOUNT THE CAMERA

Use the mounting template sheet or the camera itself to mark and drill the necessary holes in the wall or ceiling.

STEP 2 – POWERING THE CAMERA

Pass wires through and make necessary connections.

Power Options:

• PoE: Use a PoE Switch or PoE Injector to connect data and power using a single Ethernet cable.
• Non-PoE: Use a non-PoE Switch to connect data via Ethernet cable and a separate power adapter for power.

Power Requirements: DC12V, PoE (IEEE 802.3af class 3). Adapter not included.

Power Consumption: <8W

If needed, install the waterproof cap. For extreme environments, use an outdoor-rated sealer.

STEP 3 – INSTALLING THE CAMERA

1. Mount the camera to the surface using the included screws and anchors.
2. Adjust the camera's pan and tilt by loosening the lock screw at the base. Tighten the screw after adjustment.

Resetting the camera: Press the reset button at the base for five (5) seconds to perform a camera-wide reset of all settings, including network settings.

STEP 4 – CABLING

Connect power, network, alarm input/outputs, and audio to the camera. The diagram illustrates these connections.

[Textual description of cabling diagram: Shows connections for Power (DC12V/PoE), Network (Ethernet cable), Alarm Input, Alarm Output, and Audio.]

STEP 5 – MANAGING THE SD CARD (OPTIONAL)

1. Loosen the lock screw at the camera's base to rotate the module and remove the control panel cover to access the SD card slot.
2. Insert a Class 10 SD/SDHC/SDXC card (maximum 256GB) into the slot.
3. Press the card inward until it clicks to release it from the slot.

STEP 6 – DW® IP FINDER™

Use the DW® IP Finder™ software to scan the network, detect MEGApix® cameras, set network settings, or access the camera's web client.

Software Installation:

1. Visit: http://www.digital-watchdog.com
2. Search for "DW IP Finder" in the search box.
3. Navigate to the "Software" tab on the DW IP Finder page to download and install.

Software Usage:

• Open DW IP Finder and click 'Scan Devices'. The software scans the selected network and lists supported devices. The DW® logo turns gray during the scan.
• Initial Password Setup: When connecting for the first time, a password must be set. Select the camera(s), click "Bulk Password Assign", enter current credentials (admin/admin), and then the new username and password (minimum 8 characters, with at least 4 combinations of uppercase/lowercase letters, numbers, and special characters; password cannot contain the user ID). Click "change" to apply.
• Network Settings: Double-click a camera or click 'Click' to view/adjust its network settings. Settings are DHCP by default.
• Access Web Page: Click the 'Website' button.
• Save Changes: Enter the camera's admin username and password, then click 'Apply'.

Network Configuration Options:

• DHCP: Camera automatically receives an IP address from the DHCP server.
• Static: Manually enter the camera's IP address, (Sub)Netmask, Gateway, and DNS information. This is required when connecting to Spectrum® IPVMS.

Contact your network administrator for assistance.

For external network access, port forwarding must be configured on your router.

STEP 7 – WEB VIEWER

Access the camera's web interface to view live streams and configure settings.

Access via DW IP Finder:

1. Find the camera using DW IP Finder.
2. Double-click the camera's view in the results table.
3. Press the 'Website' button to open the web viewer in your default browser.
4. Enter the username and password set during the DW IP Finder setup. If no new password was set, you will be prompted to create one.

Access via Web Browser:

1. Open a web browser.
2. Enter the camera's IP address and port in the address bar (e.g., http://<ipaddress>:<port>). Port forwarding may be necessary for access from a different network.
3. Enter the camera's username and password.

Note: GUI display may differ by camera model. Some menu options may vary. Refer to the full manual for details.

WHAT'S IN THE BOX

• Quick setup and Installation guides: 1 set
• Tapping Screws: 3pcs
• Mounting Template: 1
• Plastic Plugs: 3pcs
• Waterproof Cap: 1 set
• Rubber Plug: 1
• Hexagonal Wrench (2mm): 1

Default Login Information

Username: admin

Password: admin

You will be prompted to set a new password upon first login, either via DW® IP Finder™ or the camera's browser menu.