Pelonis Digital Ceramic Tower Heater

Safety Precautions

To prevent injury to the user or other people and property damage, the instructions shown here must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The different levels of risk are shown by the following indications:

⚠️ WARNING: This symbol indicates a hazardous situation which, if not avoided, could result in death or serious injury.

⚠️ CAUTION: This symbol indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

ℹ️ NOTICE: This symbol addresses practices not related to physical injury.

Important Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, and hyperthermia, including the following:

1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
9. CAUTION: This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances or other electronics working.
11. CAUTION: It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
12. To disconnect heater, turn controls to off, then remove plug from outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
17. CAUTION: Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to avoid burns.
19. CAUTION: To prevent electric shock, match wide blade of plug to wide slot and fully insert.
20. This heater may include an audible (a visual) alarm to warn that parts of the heater are getting excessively hot. If the alarm sounds (flashes), immediately turn the heater off and inspect for any objects on or adjacent to the heater that may cause high temperatures. DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING (FLASHING).
21. Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
22. To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a confined space around infants, or individuals with reduced physical, sensory, or mental capabilities.

SAVE THESE INSTRUCTIONS

Part Names

The heater consists of the following parts:

• Display screen: Shows current settings and status.
• Control panel: Located on the top of the unit for manual operation.
• Rear cover: Houses internal components.
• Grille: Allows air intake and output.
• Front cover: The main body of the heater.
• Base: Provides stability for the unit.

Diagram Description: The manual includes diagrams illustrating the heater's external parts and a close-up of the control panel. The control panel features a display area showing temperature (e.g., 80°F), an 'eco' mode indicator, and icons for timer, ON/OFF, oscillation, and function selection. Buttons for '+' and '-' are used for temperature and timer adjustments.

NOTICE: All pictures in this manual are for explanation purposes only. Any discrepancy between the real object and the illustration shall be subject to the real model.

Operating Instructions

Check before turning on the machine

1. Check if the power cord is in good condition.
2. The product uses a 120V AC power supply. Confirm that the power socket's rated current meets local requirements with a safe grounding device. If not, replace it with a qualified socket.

Start the machine

Plug the unit into a grounded 120V outlet. The power light will illuminate ('on'), indicating the heater is energized. Press the ON/OFF key (or the ON/OFF key on the remote controller) to start. The machine supplies air at high power, and the digital screen displays "HI".

Function setting

Repeatedly press the "Function" key to cycle through the heater modes: "high - low - ECO mode - fan - high".

Temperature setting

In ECO mode, press "+" or "-" to set the desired temperature, ranging from 41-95°F. The machine stops working and enters standby when the room temperature exceeds the set temperature by 4°F. It will resume heating when the temperature drops below the set point.

Timing function

When the heater is on, press the TIMER key to enter the timing stop state (0-12 hours). Use the "+" key to increase the timing stop time and the "-" key to decrease it.

Forced shutdown function

If the machine runs for 15 hours without any operation, it will automatically shut down.

Oscillation function

Press the "Oscillation" key to activate the oscillation function. Pressing it again turns it off. When the heating function stops, the oscillation function also stops.

Temperature sensor short circuit, open circuit protection function

If the temperature sensor experiences a short circuit or open circuit, the digital screen will display "E1" or "E2" and flicker continuously. Any key operation will be invalid, and the buzzer will sound 10 times.

Safety protection

In the start state, if the room temperature exceeds 122°F, all outputs will be closed. The digital screen will display "FF" and flash once per second. Key operations will be invalid; power cycling is required to exit protection mode.

Tip-over switch

As a safety measure, the unit will shut off automatically if it is knocked over. To reset, turn the heater off, stand it upright, and then switch it back on.

ECO energy saving function

Select the ECO energy saving gear and set the temperature. The heater adjusts its heating gear based on the comparison between ambient temperature and the set temperature.

Remote controller

The functions of the remote controller are essentially the same as the body operation panel. Use the remote within 16ft (5m) and 30° of the heater's control panel. The remote requires one 1.5V AAA battery (manganese or alkaline, recyclable). Do not mix old and new batteries, or different battery types (alkaline, carbon-zinc, rechargeable).

Specifications

Power supply: AC 120V ~ 60Hz

Troubleshooting

If the product does not operate or operates improperly, check the following list. If the cause is not found, the product may have failed, and it is recommended to send it for repair.

Cleaning and Storage

It is recommended to clean the heater at least once during the operating season for optimum performance. ALWAYS turn the power switch OFF and UNPLUG the heater BEFORE CLEANING. Save the original packaging for off-season storage.

• Turn the heater “OFF”, unplug it, and wait for it to cool down.
• Use a dry cloth only to clean external surfaces.
• Do not use cleaning agents or detergents.
• Never immerse the heater in water.
• Store the heater in its original packaging in a dry and cool location.
• Any other maintenance must be performed by an authorized representative.

Warning: This heater cannot achieve accurate temperature control of the environment and thus, cannot be used as a temperature control device for storage locations, items, animals, plants, or other environments.

Service and Support

For warranty claims or service, please contact Pelonis:

Toll Free: 1-866-646-4332

For questions or comments, write to:

Midea America Corp
759 Bloomfield Ave., # 386
West Caldwell, NJ 07006-6701

Email: customersupport@pelonis.com

For your records, staple your sales receipt to this manual and record:

DATE OF PURCHASE:

PLACE OF PURCHASE:

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS

PRINTED IN CHINA

One (1) Year Limited Warranty

Please read all instructions before attempting to use this product.

This is the only express warranty for this product and is in lieu of any other warranty or condition.

This product is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or any component found to be defective, at Pelonis' option. You are responsible for all costs associated with returning the product to Pelonis and Pelonis returning the product or component under this warranty to you. If the product or component is no longer available, Pelonis will replace it with a similar one of equal or greater value.

This warranty does not cover wear from normal use, operation not conforming to instruction manuals, or damages resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or gift recipient. Keep the original sales receipt as proof of purchase is required to make a warranty claim.

This warranty is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as specified on the label.

Pelonis disclaims all claims for special, incidental, and consequential damages by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty.

This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental, or consequential damages, so the foregoing limitations may not apply to you.

Please note that failure to complete and submit this form does not diminish your warranty rights.