24V FUSE - RGB Outdoor

Product Overview

Project: _________________________ Length: _________________________

Covered by a silicone sleeve and factory sealed to each specific length.
3-in-1 RGB chip
Tight SMD LED spacing produces smooth visual delivery
Multiple mounting options with Tivoli's Urban channel series.
Dimmable with DMX protocol (see power supply page for options)
DMX Controllable and compatible with Tivoli's own CUEpro software (sold separately)
Low Voltage (24V DC)
IP67 rated
3 year warranty

Dimensions

LED tape in silicone sleeve: A diagram showing a cross-section of the LED tape embedded within a clear, flexible silicone sleeve.

LEDs On Center Spacing: Diagrams illustrating the spacing between individual LEDs along the tape, typically around 5/16 inch (8mm), and the overall width of the tape, approximately 7/16 inch.

Order Guide

The product code is structured as follows:

PRODUCT CODE: TPLFS

TPLFS = Fuse Tape
INSTALL: O = Outdoor
LED TYPE: RGB = RGB mixing
*MAX RUN: MR = Max Run
VOLTAGE: 24 = 24V DC

Note: A layout/drawing must accompany each order showing run length and location. Runs with LEAD-C are rounded up to the next cut interval (unless otherwise specified). Runs with LEAD-D are rounded down to the next cut interval (unless otherwise specified).

Specifications

Electrical

Specification	Details
Input Voltage	24V DC
Dimming Option	DMX
Power Supply	Class 2
Wire Size (End Prep)	20 AWG, 4 wire
Power Consumption	4.4W/ft.
Color Temperature (CCT)	Red (620-625 nm), Green (527-532 nm), Blue (470-475 nm)
Lumen Output	125 (Total On)

Physical

Specification	Details
LED Package	3535
Cut Increments	2" (non-field cuttable - Factory prep only)
LEDs/ft.	36
Operating Temperature	-40°F (-40°C) to 140°F (60°C)
Maximum Run Length	22'
Copper Trace	3 oz.
Adhesive	3M VHB Tape
Dimension	5/16" (8mm) TivoTape, 7/16" Silicone Sleeve

Performance

Specification	Details
Lumen Maintenance (L70) Hours	60,000
Binning Tolerance	2 Step MacAdam Ellipse

Warranty

Details
3 Years

Certification and Testing

Specification	Details
Certification	cULus
Environment	Wet Location
IP Rating	IP67

Power Leads and Jumpers

Accessories installed by Tivoli's certified solderers:

TPL-O-LEAD-4-C: LEAD/END. 24" standard 4 conductor 22AWG lead wire factory attached to one end of tape.
TPL-O-LEAD-4-D: LEAD/LEAD. 24" standard 4 conductor 22AWG lead wire factory attached to both ends of tape.
TPL-O-XEP-4: EXTRA LEAD WIRE. Additional factory attached 22AWG lead 4 wire to extend lengths of LEAD-C and LEAD-D up to 20 ft. max. Sold per foot.
TPL-O-CONN: 18-22AWG BUTT CONNECTORS. Used to interconnect factory attached lead wires. Sold individually.
GELJB-3-01-BK: 1/2/3 Wire IP67 Small Gel Filled Junction Box.
GELJB-3-02-BK: 1/2/3 Wire IP67 Medium Gel Filled Junction Box.

Compatible Extrusions

MCHAN-8-LP: Low profile, NO LENS OPTION, clear polycarbonate, length 8'.
TPL-I-45-MCH-8-S: White PVC, 45˚ angle, NO LENS, length 8'.
DWAR-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
EDGE-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
COTA-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
MOFT-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
DYER-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
WRNR-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
NOYS-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
VALN-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
DOME-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
ALTN-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
MRSL-CHAN-SLV-6.5: Anodized aluminum extrusion available in 6.5' length.
HRIZ-CHAN-SLV-6.5: Anodized aluminum extrusion available in 6.5' length.
ASTR-CHAN-SLV-6.5: Anodized aluminum extrusion available in 6.5' length.
EDIN-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
FRE-CHAN-SLV-6.5: Anodized Aluminum Extrusion, available in 6.5' lengths.
RIDG-CHAN-SLV-8: Anodized Aluminum Extrusion, length 8'.
DUET-04-CHAN-XXX-6.5: Aluminum extrusion, available in 6.5' lengths. XXX indicates color (SLV: silver, WHT: white, GLD: gold, BLK: black).
DUET-04-CHAN-SLV-6.5: Anodized aluminum extrusion available in 6.5' length.

In-Wall Controls

TVOQ-1-WH: White touchscreen control.
TVOQ-10-XX-7: Touchscreen control, where XX can be BK (Black) or WH (White).
TVOQ-2-BK: Black touchscreen control.
MDRX-AURA-XX: MADRIX Aura stand-alone controller for up to 2, 12, or 32 universes per unit.

DMX Sub-Controller

DESCRIPTION	CAT NO	MODES	WATTAGE	PRIMARY VOLTAGE	DIMENSION
DMX Sub-controller	TPL-RGBW-180-24	Sub-controller only	5X96W	24V DC	2.87" W X 6.46" L X 1.45" H

Power Supplies

ADNM - DMX SINGLE ADDRESS

DESCRIPTION	CAT NO	APPLICATION	PRIMARY VOLTAGE	SECONDARY VOLTAGE	CIRCUIT BREAKERS	MAX LOAD	CIRCUIT CAPACITY
ADNM Series Class 2 Transformer	ADNM-90-1-4-24-DIN	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	1	90W	3.75A
ADNM Series Class 2 Transformer	ADNM-120-1-4-24-DIN	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	1	96W	4A
ADNM Series Class 2 Transformer	ADNM-240-2-4-24-DIN	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	2	2x96W	2x4A
ADNM Series Class 2 Transformer	ADNM-320-3-4-24-DIN	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	3	3x96W	3x4A

ADNM - DMX MULTI ADDRESS

DESCRIPTION	CAT NO	APPLICATION	PRIMARY VOLTAGE	SECONDARY VOLTAGE	CIRCUIT BREAKERS	MAX LOAD	CIRCUIT CAPACITY
ADNM Series Class 2 Transformer	ADNM-240-2-4-24-DIN-2	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	2	2x96W	2x4A
ADNM Series Class 2 Transformer	ADNM-320-3-4-24-DIN-3	Indoor / Outdoor	100-277V AC 50/60 Hz	24V DC	3	3x96W	3x4A

ADNM - DMX/DALI FLICKER-FREE FOR TV STUDIO

DESCRIPTION	CAT NO	APPLICATION	PRIMARY VOLTAGE	SECONDARY VOLTAGE	CIRCUIT BREAKERS	MAX LOAD	CIRCUIT CAPACITY
ADNM Series Class 2 Transformer	ADNM-120-1-4-24-DTV	Indoor / Outdoor	100-277V AC 50/60 HZ	24V DC	1	1x96W	1x4A
ADNM Series Class 2 Transformer	ADNM-240-2-4-24-DTV	Indoor / Outdoor	100-277V AC 50/60 HZ	24V DC	2	2x96W	2x4A
ADNM Series Class 2 Transformer	ADNM-320-3-4-24-DTV	Indoor / Outdoor	100-277V AC 50/60 HZ	24V DC	3	3x96W	3x4A

Accessories

DMX SPLITTER (DMX-SPLT-8): 8 ports of DMX 512, RJ45 and 3-pin Hardwire Connection.
ARTNET-to-DMX (ARTNET-L-X-512): X = 8 (8 Ports) or 16 (16 Ports). 8 or 16 port universe Artnet to DMX interface.
NETGEAR Switch (NTG-SWI-XXPT): XX = 8 (8 Ports) or 16 (16 Ports). 16-Port gigabit Unmanaged Switch.

Software

Cue™ and CuePro™ softwares are specifically designed for the Tivoli CUE™ in-wall DMX controls. They include an array of tools required by the latest DMX lighting fixtures, offering intuitive, easy-to-use effects that can be dropped into timelines, and multi-zone synchronization capabilities to program projects effortlessly.

For more information, visit www.tivolilighting.com.

	Tivoli 24V FUSE - RGB LED Strip: Specifications, Extrusions, and Accessories Explore the Tivoli 24V FUSE - RGB LED strip, a versatile lighting solution. This document details product specifications, order information, compatible aluminum extrusions, power supplies, and control accessories for professional lighting installations.
	Tivoli 24V FLOW Indoor LED Lighting: Specifications and Accessories Detailed specifications, order guide, power supplies, and compatible extrusions for the Tivoli 24V FLOW Indoor LED lighting system. Features dim-to-warm capabilities, high efficacy, and various accessories.
	Tivoli 24V FUSE RGB+W+W Outdoor LED Strip Specifications Detailed specifications for the Tivoli 24V FUSE RGB+W+W Outdoor LED strip, including features, electrical and physical specifications, compatible accessories, and control options.
	Tivoli 24V FUSE - Pixel24 RGB LED Strip Specifications Comprehensive technical specifications, features, and compatibility information for the Tivoli 24V FUSE - Pixel24 RGB LED strip, including control systems, extrusions, and power supplies.
	Tivoli Litesphere True RGB+W LED Lighting System: Specifications and Guide Explore the Tivoli Litesphere True RGB+W, a 24V DC LED lighting system offering advanced color control, DMX512 compatibility, and MADRIX software integration. This document details product features, specifications, order guides, wiring diagrams, mounting options, and accessories for versatile architectural and decorative lighting applications.
	Tivoli Illumiwall 2.0 RGB+W: High-Quality LED Lighting System Specifications Detailed specifications, features, and technical data for the Tivoli Illumiwall 2.0 RGB+W LED lighting system, including photometric data, control options, and installation guidelines.
	Tivoli ELITE SB TivoTape: 24V Indoor LED Lighting with Zero Drop Technology Explore the Tivoli ELITE SB TivoTape, a 24V indoor LED lighting solution featuring Zero Drop Technology, high CRI, IP67 rating, and a wide range of compatible extrusions and power supplies. Ideal for various lighting applications.
	Tivoli Litesphere True RGB+W LED Lighting System Specifications and Guide Detailed information on the Tivoli Litesphere True RGB+W LED lighting system, covering features, specifications, order guides, wiring diagrams, accessories, mounting options, and power supplies. Ideal for architectural and landscape lighting applications.