LNC A04965A Chandelier Installation Guide

WARNING

To reduce the risk of fire, electric shock, or personal injury:

• Installation by a licensed electrician is suggested.
• Read instructions carefully and save for future reference.
• Before starting, shut off electricity at the main fuse or circuit breaker box and the wall switch.
• Mounting surface must be clean, dry, flat, strong, and at least 1/4” larger than the canopy on all sides. Correct any gaps exceeding 3/16”.
• Ensure the ceiling or wall can support the lamp's weight.
• Verify voltage is 120V. Maximum wattage is LED, 20W.
• Keep the lamp away from acidic and alkaline substances to prevent surface damage.
• When replacing bulbs, turn off or unplug the lamp and wait for it to cool down.
• Safety instructions are not exhaustive; use common sense, caution, and care with electrical products.

Finished Product Appearance

A visual representation of the assembled chandelier shows a fixture with multiple hanging crystal strands suspended from a central canopy, attached by wires and cables.

Tools Required (Not Included)

Before starting assembly and installation, prepare the following tools:

• Ladder: For reaching the installation area.
• Philips Head or Flat Blade Screwdriver: For screws.
• Electrical Tape: For securing wire connections.
• Pliers: For gripping and manipulating wires or parts.
• Wire Cutter/Stripper: For preparing wires.

Parts Type & Quantity Including

The fixture includes the following parts:

• (A) Mounting plate (1)
• (B) Green ground screw (1)
• (E) Stud (2)
• (F) Canopy (1)
• (G) Lock nut (4)
• (H) Steel Wire (3)
• (I) Cable (1)
• (J) Body assembly (1)
• (K) Crystal hook (53)
• (L) Crystal (53)

Accessories & Quantity Enclosed

The package also contains accessories:

• (C) Plastic wire connector (3)
• (D) Mounting screw (2)
• (K) Crystal hook (2) (spare part)
• (L) Crystal (2) (spare part)

Assembly & Installation Instructions

1. Carefully remove the fixture from the carton and verify all parts and accessories are present as illustrated.
2. Turn off power: Before starting, ensure electricity is shut off at the main fuse/breaker and wall switch.
3. Unscrew studs (E) from canopy (F) and remove mounting plate (A).
4. Attach mounting plate (A) to the outlet box using mounting screws (D). The diagram shows the mounting plate being secured to an electrical outlet box.
5. Make wire connections: Connect wires as shown. IMPORTANT: The ground wire is bare copper; do not connect other wires to it.

   Ground Wire Connections:

   • Connect the fixture's ground wire to the outlet box's ground wire using the green ground screw. This is shown in diagram A, illustrating a connection with a dimple and cupped washer. Diagram B shows an alternative connection for fixture ground to outlet box ground, also using a green ground screw.

   Main Wire Connections:

   Connect Black or Red Supply Wire to:	Connect White Supply Wire to:
   Black (*Parallel cord: round & smooth; Clear, Brown, Gold or Black without tracer; Insulated wire (other than green) with copper conductor)	White (*Parallel cord: square & ridged; Clear, Brown, Gold or Black with tracer; Insulated wire (other than green) with silver conductor)

   Note: For parallel wires (SPT-I & SPT-II), the neutral wire is square or ridged, and the other wire is round or smooth.

   • Twist wires together with plastic wire connectors until tightly joined.
   • Wrap each connector with approved electrical tape.
   • Ensure no wire strands are exposed and carefully tuck all wires into the outlet box.
6. Raise canopy (F) to the ceiling and secure it by tightening studs (E) onto the pre-assembled screws in mounting plate (A). The diagram illustrates the canopy being attached to the ceiling mounting plate.
7. Hang crystals (L) to the holes of the body assembly (J) using crystal hooks (K) as shown.
8. To adjust hanging height: Press and hold lock nuts (G), then pull or push steel wires (H) and cable (I) in and out of the canopy (F). Adjust steel wires first. The diagram shows how to adjust the height by manipulating lock nuts and wires.
9. Check all installations are correct, then turn on the light. Enjoy!

Ordering Parts

Keep this sheet for future reference for ordering replacement parts. All parts can be ordered from the place of purchase. Use the exact wording from the illustration when ordering.

Cleaning

Wipe the fixture with a soft cloth. Clean glass with a mild, non-abrasive cleaner (like mild soap). Avoid abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.