BESTÅ Assembly Instructions
Important Safety Information
⚠️ WARNING!
Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.
עברית
אזהרה! נפילת הרהיט עלולה לגרום לפגיעה גופנית חמורה או קטלנית.
על מנת למנוע את נפילת הרהיט, יש לקבע אותו לקיר באמצעות אבזרי הקיבוע הכלולים באריזה.
הברגים לקיבוע אינם כלולים מכיוון שיש להתאים אותם לחומר ממנו עשוי הקיר המיועד. לקבלת מידע נוסף על הברגים המתאימים לקיבוע, אנא פנו לאיש מקצוע. קראו ופעלו לפי ההוראות המפורטות בזהירות.
Parts List
| Part Number | Description | Quantity |
|---|---|---|
| 130618 | Screw | 8x |
| 114667 | Cam Lock | 8x |
| 26516 | Cam Lock Nut | 2x |
| 133194, 133195, 133196, 133303, 133304, 126918 | Various small parts (likely for drawer/door runners or hinges) | 2x |
| 114947, 115988 | Adjustable Foot | 4x |
| 100006 | Allen Key | 1x |
| 114929 | Bracket/Connector | 2x |
| 116637 | Screw | 2x |
| 141413 | Hinge/Mounting Bracket | 2x |
| 141414 | Cap/Cover | 2x |
| 126916 | Wall Attachment Hardware | 2x |
| 113301 | Shelf Support | 2x |
Assembly Steps
Step 1: Attach Feet
Place the base panel on a soft surface. Attach four adjustable feet (parts 114947/115988) to the underside of the base panel using screws (part 130618).
Diagram shows: Base panel flat, four feet being screwed into pre-drilled holes on the corners.
Step 2: Attach Side Panels
Insert cam lock screws (part 130618) into the base panel. Attach the two side panels to the base panel by aligning the holes and securing them with cam locks (part 114667). Ensure 8 screws and 8 cam locks are used.
Diagram shows: Side panels being connected to the base panel, with close-ups of cam lock assembly.
Step 3: Attach Back Panel
Slide the back panel into the grooves on the side and base panels, or attach it using the provided fasteners.
Diagram shows: Back panel being inserted into the frame.
Step 4: Attach Top Panel
Insert cam lock screws into the top edges of the side panels. Place the top panel onto the side panels and secure it using cam locks (part 114667).
Diagram shows: Top panel being placed and secured with cam locks.
Step 5: Insert Internal Components
Slide any internal dividers or shelf supports into their designated positions within the frame.
Diagram shows: A panel being slid into the unit.
Step 6: Secure Back Panel
Attach the back panel or a reinforcing element to the rear of the unit.
Diagram shows: Back panel being fastened.
Step 7: Secure Internal Fittings
Use cam locks to secure internal fittings or shelf supports.
Diagram shows: Cam lock being used to secure a component.
Step 8: Position Unit Upright
Carefully rotate the assembled unit into its upright position.
Diagram shows: The unit being turned upright.
Step 8 (Detail): Attach Mounting Brackets
Attach two mounting brackets (part 141413) to the upper sides of the cabinet frame using screws (part 116637).
Diagram shows: Mounting brackets being screwed into the side of the cabinet.
Step 9: Level the Unit
Use the provided Allen key (part 100006) to adjust the feet (parts 114947/115988) to ensure the unit is level.
Diagram shows: Allen key turning adjustable feet.
Step 10: Further Leveling
Continue adjusting the feet until the unit is stable and level on the floor.
Diagram shows: Person adjusting feet.
Step 11: Secure to Wall (Part 1)
Position the unit against the wall. Attach the wall attachment hardware (part 126916) to the unit and the wall using appropriate screws and wall plugs (not included). Ensure a secure connection ("CLICK!").
Diagram shows: Wall attachment hardware being installed to secure the unit to the wall.
Step 12: Attach Caps
Place the decorative caps or covers (part 141414) onto the top of the unit.
Diagram shows: Caps being placed on top.
Step 13: Insert Shelf Supports
Insert shelf pins or supports (part 113301) into the pre-drilled holes on the inside of the side panels at the desired shelf heights.
Diagram shows: Shelf pins being inserted.
Step 14: Secure to Wall (Part 2)
Repeat the wall attachment process as shown in Step 11, using the second set of wall attachment hardware (part 126916).
Diagram shows: Wall attachment hardware being installed.
Step 15: Add Shelves
Place the shelves onto the inserted shelf supports.
Diagram shows: Shelves being placed on supports.
Step 16: Final Check
Ensure all parts are securely fastened and the unit is stable and properly attached to the wall.
Diagram shows: The completed unit.
