Pyle Wireless BT Streaming Mini Audio Mixers

Introduction

For the best results and satisfaction with your new unit, please read this manual thoroughly and retain it for future reference.

ATTENTION

To avoid the possibility of malfunction/damage to the product, damage to data, or damage to other property, please follow the points below.

Operation and Maintenance

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise.
• To prevent panel disfiguration, unstable operation, or damage to internal components, do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day).
• Do not place vinyl, plastic, or rubber objects on the device, as this might discolor the panel.
• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
• Condensation can occur due to rapid, drastic changes in ambient temperature when the device is moved or the air conditioner is turned on or off. Using the device while condensation is present can cause damage. If condensation might have occurred, leave the device for several hours without turning on the power until it has completely dried out.
• Avoid setting all controls to their maximum. Depending on the connected devices, this may cause feedback and damage speakers.
• When turning on the power in your audio system, always turn on the power amplifier LAST to avoid speaker damage. When turning the power off, turn the power amplifier off FIRST for the same reason.

Pyle PAD12MXUBT

Features

• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Combo Jack (XLR+6.35mm) for MIC/LINE/GUITAR Inputs
• RCA Jacks for Stereo Input and Output
• 3.5mm Jack for Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis

What's in the Box

• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable

Technical Specs

• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 4.72" x 3.95" x 1.38" inches

Pyle PAD22MXUBT

Features

• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Combo Jack (XLR+6.35mm) for MIC/LINE/GUITAR Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• 6.35mm Jacks for Stereo Input and Output
• 6.35mm Jack for Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis

What's in the Box

• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable

Technical Specs

• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 4.80" x 4.19" x 1.38" inches

Pyle PAD33MXUBT

Features

• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Built-in Echo Effect
• Extremely Musical 2-band EQ & PAN on each Channel
• Combo Jack (XLR+6.35mm) for MIC/LINE Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• RCA Jacks for Stereo Input and Output
• 2-TK RCA Input Jacks
• 3.5mm Jacks for Microphone Input & Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis

What's in the Box

• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable

Technical Specs

• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 5W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 5.35" x 3.95" x 1.38" inches

Pyle PAD43MXUBT

Features

• Ultra-low Noise Design with High Headroom
• USB Sound Card/Audio Interface, for Computer Playing & Recording
• Built-in Echo Effect
• Extremely Musical 2-band EQ & PAN on Each Channel
• Combo Jacks (XLR+6.35mm) for MIC/LINE Inputs
• Independent 3.5mm Stereo Input Jack
• Flexible Connectivity for a Variety of External Devices
• RCA Jacks for Stereo Input and Output
• 2-TK RCA Input Jacks
• 3.5mm Jacks for Microphone Input & Earphone Monitor Output
• +48V Phantom Power
• DC 5V Power Supply, or PC Power Supply
• Rugged Metal Chassis

What's in the Box

• Mini Mixer
• (2 Flat Plug) Power Adapter
• USB Cable

Technical Specs

• USB Sound Card: 2.0 Type-B
• Power Supply: DC 5V, 500mA
• Voltage: 100/240V
• Power Consumption: 7W
• USB Cable Length: 3.94 ft.
• Product Dimensions (L x W x H): 5.35" x 5.13" x 1.38" inches

Controls and Functions

Precautions When Using the USB 2.0 and 5V DC Terminals

When connecting the USB 2.0 connector to a computer, please follow these points. Failure to do so may cause computer crash, breakdown, or data loss. If the computer or mixer crashes, restart the application software or computer operating system, or disconnect the mixer, then power on again.

• Use an AB type USB cable. USB 3.0 cable cannot be used.
• Before connecting the computer to the USB 2.0 terminal, exit from any power-saving mode of the computer (such as suspend, sleep, standby).

Controls for PAD12MXUBT - PAD22MXUBT

1. [MIC/LINE & GUITAR]

Input jack, this combo jack can be used to connect a mono signal such as an XLR microphone or 1/4" line input device, or connect with an instrument such as an electric guitar or an electric bass. They need to be converted with SWITCH 2.

2. [MIC/LINE & GUITAR]

Converting switch, for converting the different input source. Press down this switch to connect with a high impedance audio source, such as an electric guitar or bass. When the switch is bounced up, it connects with XLR microphone or 1/4" low impedance audio device.

3. [LINE IN]

Controller, used to adjust the volume from RCA LINE IN input.

4. [CH 1/2/3]

Controller, used to adjust the volume of signal input of CH1/2/3.

5. [PEAK] LED Indicator

This LED indicator light will light up when the input signal is too high.

6. [PHANTOM +48V] Switch

Used to activate the phantom power supply on XLR connector, it offers +48V phantom power.

7. [PHANTOM POWER] LED

Indicates the phantom power is on.

8. Input Select Switch

When the switch is bounced up, the input signal is from LINE IN. Press it down, the input signal is from USB/BT.

9. Input Select Switch

When the switch is bounced up, the input signal is from stereo CH 2/3 and AUX IN. Press it down, the input signal is from USB/BT.

10. Input Select Switch

When the switch is bounced up, the input signal is from CH 2. Press it down, the input signal is from USB/BT.

11. [MAIN] Controller

Used to adjust the volume of MAIN and USB PORT output.

12. [CLIP] LED

This LED will light up when the MAIN output signal is too high.

13. [POWER ON] LED

This LED will light up when the mixer's power is on.

14. [PHONES] 3.5mm Output Jack

Connect with earphones; it is supporting stereo phone plug.

15. [PHONES] 6.35mm Output Jack

Connect with earphones; it is supporting stereo phone plug.

16. [PHONES] Controller

Controls the volume of earphones.

17. [AUX IN] 3.5mm Jack

This is an auxiliary STEREO input, providing flexible connectivity for a variety of external audio devices.

18. [STEREO IN] 3.5mm Jack

This is an auxiliary stereo input, providing flexible connectivity for a variety of external audio devices. The volume can be controlled by external audio devices or the MAIN controller.

19. [BT/USB] Convert Switch

When the switch is bounced up, it connects with Wireless BT. Press it down to connect with USB.

20. [LINE IN] Stereo RCA Input Jacks

Connect an audio source with line signal level, such as a CD player, tape deck, etc.

21. [CH 2/3 STEREO INPUT] Jacks

For connecting to line level devices (e.g., electric keyboard) via 6.35mm plugs. If only the L (MONO) jack is connected, the mixer will send the same mono signal to L and R outputs.

22. [MAIN MIX] Stereo RCA Output Jacks

Connect the input of an amplifier or a recorder.

23. [MAIN] Stereo 6.35mm Output Jacks

Connect the input of an amplifier or a recorder.

Controls for PAD33MXUBT - PAD43MXUBT

1. [MIC/LINE] Input Jack

Used to connect the mono signal such as an XLR microphone or 1/4" line input device.

2. [+48V PHANTOM POWER] Button/LED

When the button is turned on, the LED light is on, providing DC +48V phantom power to the XLR plug on MIC mono input. Turn on this button when using a condenser microphone powered by phantom power.

3. [LINE IN] Stereo RCA Input Jacks

Connect the audio source with line signal level, such as CD player, tape deck, etc.

4. [2-TK] Stereo RCA Input Jacks

Connect the audio source with line signal level, such as Recorder, MP3 player, etc.

5. [MAIN MIX] Stereo RCA Output Jacks

Connect the input of an amplifier or a recorder.

6. [POWER ON] LED

This LED will light up when the mixer's power is on.

7. [BT/USB] Convert Switch

When the switch is bounced up, it connects with Wireless BT. Press it down to connect with USB.

8. Input Select Switch

When the switch is bounced up, the input signal is from 2-TK. Press it down, the input signal is from AUX IN.

9. [GAIN] Controller

Determines the basic volume of CH1/2. Adjust it for maximum volume performance. When the volume gets too loud, the PEAK LED indicator will keep flashing.

10. [HIGH & LOW] Tone Controller

Adjusts the high frequency and low frequency for CH1/2.

11. [PAN] Controller

This is the panorama control or balanced control, determining the position of channel signal within the stereo image. When working in sub-groups, you can use the PAN controller to assign the signal to just one output, which gives you additional flexibility in recording situations.

12. [CH1/2] Controller

Used to adjust the volume of signal input from CH1/2.

13. [PEAK] LED Indicator

This LED indicator light will light up when the input signal is too high.

14. [ECHO EFFECT] Controller

Used to adjust the Echo effect.

15. [AUX IN] 3.5mm Jack

This is an auxiliary input, providing flexible connectivity for a variety of external audio devices. The volume can be controlled by external audio devices or the MAIN MIX controller.

16. Input Select Switch

When the switch is bounced up, the input signal is from LINE IN. Press it down, the input signal is from USB/BT.

17. Output Select Switch

When the switch is bounced up, it can be assigned to MAIN MIX output. Press it down to assign to PHONES output.

18. [LINE/USB/BT] Controller

Controls the volume of the LINE/USB/BT channel.

19. [PHONES] Controller

Controls the volume of earphones.

20. [MIC TO CH1] Jack

A 3.5mm input jack for microphone; the input audio is sent to CH1.

21. [MIC TO CH2] Jack

A 3.5mm input jack for microphone; the input audio is sent to CH2.

22. [PHONES] 3.5mm Output Jack

Connect with earphones; it is supporting stereo phone plug.

23. [CLIP L & R] LED

These LEDs will light up when the MAIN output signal is too high.

24. [MAIN MIX] Controller

Used to adjust the volume of MAIN MIX and USB PORT output.

Connectivity

USB 2.0 Terminal

Use a USB 2.0 cable (included) to connect the unit's USB Port to a USB port on the computer. When connected to a computer, it supplies power to the mixer, and audio data can be sent between mixer and computer. It can also be used with a USB power socket or USB power bank to supply power to the mixer.

When using an external power supply, it must meet the following requirements:

• Output voltage: 4.8V to 5.2V
• Output current: 0.5A or even more

If using a USB power socket or USB power bank, data transfer and recording are not possible unless the unit is connected to a computer.

Wireless BT Connectivity

• Instantly Receives Wireless Music Streaming Audio
• Works with All of Your Favorite Devices (iPhone, Android, Smartphones, iPad, Tablet, MP3 Player, etc.)
• Wireless BT Version: 5.0
• Wireless BT Network Name: 'MP'
• Wireless BT Range: 50' Feet

Support and Contact

Questions? Issues? Pyle is here to help!

Visit us online: PyleUSA.com/ContactUs

Phone: (1) 718-535-1800

Email: support@pyleusa.com