Moving Head 19x15W ZOOM User Manual

1. Introduction

Thank you for purchasing the Moving Head 19x15W ZOOM. For safety reasons and to ensure trouble-free operation, please read these instructions carefully.

2. Safety Information

Please keep this User Manual for future consultation. If you sell the fixture to another user, ensure they also receive this instruction booklet.

• Unpack and check carefully for any transportation damage before using the fixture.
• Before operating, ensure that the voltage and frequency of the power supply match the fixture's power requirements.
• It is important to ground the yellow/green conductor to earth to avoid electric shock.
• Disconnect main power before servicing and maintenance.
• Use a safety chain when fixing this fixture.
• Do not handle the fixture by its head only; always handle it by its base.
• Maximum ambient temperature: 40°C. Do not operate where the temperature is higher than this.
• In case of serious operating problems, stop using the fixture immediately. Never attempt to repair the fixture yourself. Repairs by unskilled personnel can lead to damage or malfunction. Contact the nearest authorized technical assistance center and always use the same type of spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation, as there might be a hazard of electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
• The housing must be replaced if it is visibly damaged.
• Do not look directly at the LED light spot while the fixture is on.

WARNING!

The Moving Head 19x15W ZOOM has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the Moving Head 19x15W ZOOM unless the base is securely fastened to a surface or to rigging hardware.

Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 90° clockwise.

When clamping the fixture to a truss or other structure at an angle other than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.

Position or shade the head so that the front lens is not exposed to sunlight or any other strong light source from any angle, even for a few seconds. The Moving Head 19x15W ZOOM lens can focus the sun's rays, creating a potential fire hazard and causing damage.

IMPORTANT!

Do not point strong light output from other fixtures at the Moving Head 19x15W ZOOM, as intense illumination can damage the display.

Figure 2 Description: Lenses can focus sunlight and strong light, presenting a risk of fire and damage to the fixture. Shield or shade the head if necessary.

3. Product Information

• Light Source: 19pcs x 15W 4in1 LED
• PAN range: 540°
• TILT range: 270°
• Zoom range: 10-60°
• Color: RGBW
• Zoom: Yes
• DMX Modes: 16 DMX channel mode.
• Connectors: 3-Pin XLR DMX input/output
• Power supply: 100-245V AC, 50-60Hz
• Power consumption: 300W
• Net Weight: 7.6 kg
• Weight with packaging: 55 kg (4x Moving Heads + Case)
• Dimensions: H(41)xW(32)xD(22) cm
• Case Dimensions: H(62)xW(80)xD(52) cm

4. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit's weight.

Also, always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. It must be fixed at a place that is out of the touch of people and where no one passes by or under it.

Upon removing the unit from its packaging, check for any damage incurred during transport. Before connecting to the electrical mains, ensure the unit is securely mounted. The manufacturer is not responsible for damage caused by unstable mounting.

During operation, ensure correct connection to the electrical mains and proper grounding. Verify that the electrical mains parameters comply with the device requirements. All operations involving connecting the device to the electrical mains should be performed by qualified personnel.

The unit should be installed in a well-ventilated area, at least 15cm from the nearest surface (wall, ceiling, etc.). Simultaneously, ensure that ventilation openings are not blocked and that fans are operating correctly.

5. Connection

Interfaces:

• DMX (in/out): XLR 3-pin socket
• Power (in/out): powerCON socket

5.1 Connecting DMX Signal:

The connection is performed using a cable with XLR-female to XLR-Male plugs.

CAUTION!

At the last fixture, the DMX signal must be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into an XLR plug and plug it into the DMX output of the last fixture.

DMX Connection Diagram Description: A DMX controller connects to DMX 512 fixtures using XLR cables. The XLR connectors have the following pinout: Pin 1: Ground, Pin 2: DMX+, Pin 3: DMX-.

5.2 Voltage Specification:

5.3 Connecting Power Supply:

The connection is performed using a power cable with a PowerCon connector (included). The device must be operated by qualified personnel. Ensure that the power grid supply parameters are consistent with the device parameters and limitations are not exceeded.

CAUTION!

In case of cable damage, do not attempt to repair it yourself. Replacement or repair can only be made by the manufacturer or by a person with appropriate permissions.

When using the lamp, the change rate of power voltage should be within ±10%. If the voltage is too high, it will shorten the light's life; if it's not enough, the lamp will be dark. Please restart it after turning the light off for 20 minutes until full-cooling. Frequent switching will reduce the lifespan of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

6. Setting Interface

System Settings:

• DMX Address: Set from 001-512 from machine status: receive DMX signal from console or host. Press "ok" to enter edit status. At this time, select the hundreds place, press "up" and "down". The key changes the address code. Click "ok" to select the ten editors again. Click "Determine" key again to select the individual edit. Press the exit edit status again.
• The Encoder: Start using the encoder (optical coupling) to judge the missing step and automatically correct the position. Close the correct position without encoder (decoupling).
• X Inversion: Closed/Open
• Y Inversion: Closed/Open

Operation Mode:

• Operation Mode: DMX/Voice Control/Automatic
• Channel Selection: 16CH/24CH
• Language Selection: Chinese, English
• Screen Settings: Shut Down

Factory Setup:

7. DMX Channels Setting

16 CH Mode:

24 CH Mode: