Westek USLM-PIP-RF Plug-In Puck Lights with RF Remote
Model: USLM-PIP-RF
Introduction
Thank you for purchasing this Ultra-Slim 3-puck light set, featuring 300 lumens of bright white light per puck with 5-color adjustable white control (2700K, 3000K, 3500K, 4000K, 5000K). These puck lights operate by RF remote control, meaning direct line of sight is not needed – you can operate them through walls and around corners. Alternately, these lights are equipped with a hand-wave sensor, and can be controlled by a simple wave of your hand, ideal for use during tasks like kitchen prep.
Includes
- 3 puck lights
- 3 white trim rings (preinstalled)
- 3 bronze trim rings
- 3 black trim rings
- 1 wave sensor
- 1 power supply
- 1 remote control
Optional Accessories
Expand up to 6 pucks total with add-on puck PIP-RGB-A (sold separately).
Getting Started
- Read these instructions in their entirety before using this product.
- Do not mount this product over a stove or sink.
Installation
These puck lights offer convenient, tool-free installation using 3M-branded self-adhesive tape. Prior to installing your light, select your desired trim ring color – white, black or bronze. The trim ring can be snapped onto the light by aligning the wiring cutouts on the ring to the wires on the puck and using gentle pressure to snap the trim ring into place.
Thoroughly clean all surfaces to which you will install your puck lights. Do not apply to drywall or other delicate surfaces; the adhesive may remove paint, drywall or mar other delicate surfaces upon removal.
Peel off one side of the release liner on the 3M adhesive and attach the adhesive disk to your puck light. Repeat for each puck light and for the wave on/off sensor (make sure the adhesive pad for the wave sensor is installed on the BACK side of the sensor, not blocking the IR/wave sensor).
Connect the transformer’s cable to the IR/Wave sensor. Plug the first puck into the wave sensor, the second puck into the first puck, and the third puck into the second. Up to a total of six pucks can be connected to one power supply. To avoid permanent damage to your puck lights, never connect more than six pucks to a single power supply. Do not conceal the cord inside walls, ceilings, soffit, kitchen cabinets, or other similar permanent structures. Do not run the power cord through holes in walls, ceilings, or floors.
Plug the transformer into a 120V power outlet. Finally, remove the battery pull-tab from the included remote control to activate the remote. Your lights are now ready for use.
Operation
Your puck lights can be controlled either by the remote control or the wave-sensor. To operate the puck lights from the wave sensor, wave your hand past the sensor at a distance of approximately 2-6 inches from the sensor. A single wave turns the power on or off. Pausing your hand in front of the sensor activates continuous dimming. To adjust the color temperature, press the action button on the wave sensor with your finger. The available color temperature options are 2700K, 3000K, 3500K, 4000K, and 5000K.
To operate from the remote control, simply press the desired button on the remote to activate your lights, as shown below. The remote uses radio frequency technology and can work through walls, around corners, and without direct line of sight. The remote is good to a maximum of about 50’ from the lights, but walls and other objects may shorten this working range.
Remote Control Functions
| Button | Function |
|---|---|
| ON | Turns on the lights |
| OFF | Turns off the lights |
| DIM Down | Dims the lights |
| DIM Up | Brightens the lights |
| DIM 50% | Sets light to 50% brightness |
| DIM 100% | Sets light to maximum brightness |
| Timers | Programs the light to turn off automatically in 15, 30, 60, or 120 minutes |
| Warm CCT | Sets the light to 2700K white temperature |
| Next CCT | Cycles between 2700K, 3000K, 3500K, 4000K, and 5000K white temperatures |
| Cool CCT | Sets the light to 5000K white temperature |
The remote control features an "Action Button" and a "Wave Sensor" for operation.
Warnings
Do not disassemble or modify this light. Modification voids the manufacturer’s warranty and any applicable regulatory certifications this light may possess.
Safety Warning: This light may present a possible shock or fire hazard if not properly installed. Products should be installed per these instructions, and in accordance with all local and national electrical codes.
Surface Warning: Do not apply to drywall or other delicate surfaces; the adhesive may remove paint, drywall or mar other delicate surfaces upon removal.
Power Supply Warning: To avoid permanent damage to your puck lights, never connect more than six pucks to a single power supply. Do not conceal the cord inside walls, ceilings, soffit, kitchen cabinets, or other similar permanent structures. Do not run the power cord through holes in walls, ceilings, or floors.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions explained fully in the Limited Warranty on the website.
AmerTac
AmerTac - Product Warranties
