Westek Wireless RF Remote Control System

Wall Mounted Switch RFA-108 and Plug-in Receiver RFA-110

This wireless Radio Frequency (RF) control system offers a convenient way to add switched outlet functionality without the need for wiring or an electrician. The RF signal can pass through walls, doors, ceilings, floors, and around corners. Simply plug your appliance into the receiver and the receiver into a power outlet. The transmitter is designed to resemble a standard wall switch and can be mounted on any surface using the included screws. Pressing the transmitter's toggle switch turns the connected appliance on or off, similar to a hardwired switch and outlet.

Channel Code Information

The system features three operating channels, allowing you to control up to three separate systems in different locations with the same switch. Ensure that the frequency channels are matched for devices you intend to operate together.

Instructions

Mounting and Setup

Note: The total load connected to the Plug-in Receiver should not exceed 1200 Watts or 10 Amps.
Caution: Do not use the Plug-in Receiver to control appliances that could be dangerous if turned on remotely, such as power tools.
The Plug-in Receiver must be located within 100 feet (approximately 30.5 meters) of the Wall Transmitter.
To remove the Wall Transmitter's front cover, turn the two white cover screws counter-clockwise.
Remove the plastic battery tab from the battery compartment. This tab isolates the battery until use, ensuring a fresh battery.
Reinstall the front cover using the two cover screws.
Plug your appliance into the receiver's outlet, ensuring the wide blade of the appliance plug aligns with the wide slot on the outlet.
Plug the Receiver into a standard grounded 110/120 Volt outlet, aligning the receiver's wide blade with the outlet's wide slot. Ensure it is fully inserted.
Before mounting the Wall Transmitter, hold it in the desired installation location.
Press the toggle switch to test if your appliance turns on and off. If it does not respond, try repositioning the Transmitter or Receiver. Avoid placing large metal objects, such as metal doors or cabinets, between the Wall Transmitter and Plug-in Receiver, as this can reduce the RF signal range.
Once the test is successful, remove the front cover again and mount the Wall Transmitter using the two enclosed mounting screws. (For surfaces other than wood, different mounting hardware may be required.)
Replace the front cover of the Wall Transmitter and secure it to the wall switch with the white cover screws. Do not overtighten.

Operation

Simply press the toggle switch to turn the connected light or appliance on or off. Note: Wait at least 3 seconds after pressing the transmitter before pressing it again to allow the RF signal transmission to complete.

Battery Replacement

The RFK100 battery typically lasts 2-3 years with normal use.

Remove the front cover of the Wall Transmitter by turning the two white cover screws counter-clockwise.
Remove the old battery from the battery compartment and replace it with a new 12Volt battery (e.g., Radio Shack™ 23, 23M, VR22, EL22, or equivalent).
Replace the front cover and secure it with the screw.

Troubleshooting Guide

Symptom	Probable Cause
Light does not turn on.	1. Circuit breaker or fuse is off. 2. Switch on the lamp is turned off. 3. Bulb is defective. 4. Weak battery. 5. Lamp module or lamp is loose.
Light does not turn off.	1. Transmitter signals are being blocked. Check for metal objects that could block the signal, or reposition the transmitter. 2. Switching too fast. Wait 3 seconds between toggles. 3. Weak battery.
Light comes on randomly.	1. Short-term power line failure. 2. Transmitter out of range. 3. Lamp module or lamp is loose.

Specifications

Receiver: RFA-110

120V~60Hz
10A Resistive load
240W tungsten lamp load
FCC ID: XDE-RFA110

Transmitter: RFA-108

Battery: 12VDC
Frequency: 315MHz
FCC ID: XDE-RFA108
For indoor use only.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warranty Information

One-Year Limited Warranty: AmerTac warrants to the original purchaser that this product will be free from defects in materials and workmanship for a period of one year from the date of purchase. Additional details are available at www.amertac.com.

Prop.65 WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.

	Westek USLM-PIP-RF Plug-In Puck Lights with RF Remote - Installation and Operation Guide Comprehensive guide for Westek USLM-PIP-RF plug-in puck lights. Learn about installation, RF remote and wave sensor operation, dimming, color temperature adjustment, and troubleshooting.
	Westek WiFi Enabled Multi-Color Puck Lights: Installation and Operation Guide Comprehensive guide for Westek WiFi enabled multi-color puck lights (PIP-RGB-WIFI, PIP-RGB-A). Covers installation, wave sensor control, app features, Wi-Fi setup, operation, specifications, warnings, and warranty information.
	Westek TM77DHB Indoor Daily Timer Instructions and Warranty This document provides instructions and warranty information for the Westek TM77DHB Indoor Daily Timer. Learn how to set on/off periods, set the time, connect the timer, and use manual override functions. Specifications and precautions are also included.
	Westek TE02DHB/TE22DHB Indoor 1-Outlet Digital Timer: Instruction Manual & Warranty Comprehensive guide for the Westek TE02DHB/TE22DHB 1-Outlet Digital Timer, covering features, programming, safety precautions, and a one-year limited warranty.
	Westek TM1677DHB 1-Outlet Mechanical Timer: Instruction Manual & Warranty This document provides instructions for setting up and using the Westek TM1677DHB 1-Outlet Mechanical Timer. It covers programming, setting the time, manual override, ratings, and warranty information.
	Westek TAPE10RCWF-T WiFi Enabled RGB/CCT LED Light Strip User Manual and Instructions Comprehensive guide for the Westek TAPE10RCWF-T WiFi Enabled RGB/CCT LED Light Strip, covering installation, safety, WiFi pairing, app control, and specifications. Learn how to control colors, brightness, and set schedules using the Westek app and voice assistants.