Baby Trend PY57 Nursery Center: Instruction Manual and Warranty

Warranty Information

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered or removed serial number, invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user. The Customer Service Department can be contacted at 1 (800) 328-7363 Monday through Friday between 8:00 am and 4:30 pm (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Warranty is valid only in North America.

Important Instructions

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

Parts List

Check the parts list to ensure you have all the parts for this model before assembling the playard.

• Playard: The main structure of the playard.
• Mattress: The padded floor mat for the playard.
• Travel / Storage Bag: A bag for carrying or storing the playard.
• Short Bar with Connectors (2): Two short bars with connecting knobs, likely for the changing table.
• Long Curved Bar (2): Two long curved bars, likely for the changing table.
• Bassinet with metal support tubes: A bassinet attachment with metal supports.
• Changing Table: An attachment for changing diapers.
• Removable Rock-A-Bye Bassinet**: A detachable bassinet feature.
• Music Center*: An electronic unit with music, nature sounds, sleep sounds, vibration, and night light. Available with or without vibration.
• Diaper Stacker*: An accessory for holding diapers.
• Parent Organizer*: An accessory for organizing parent items.

*Type may vary **Type and quantity may vary

Safety Warnings

WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation.

WARNING: INFANTS CAN SUFFOCATE:

• In gaps between a mattress too small or too thick and product sides
• On soft bedding

Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by manufacturer. Never use a water mattress with this product.

WARNING: See playard floor and side rails for warning.

WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.

• The playard, including side rails, must be fully erected prior to use. Make sure latches are secure.
• Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys.
• Discontinue use of the product when child is able to climb out or has reached the height of 35 in. (890 mm) or weight of 30 lbs. (13.6 kgs), whichever comes first.
• When child is able to pull to standing position, remove bumper pads, large toys and other objects that could serve as steps for climbing out.
• NEVER place product near a window where cords from blinds or drapes can strangle a child.
• Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
• Child can become entrapped and die when improvised netting or covers are placed on top of a playard. Never add such items to confine child in playard.
• NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
• NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
• This product is not intended for commercial use.
• If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimension of the bassinet or cradle mattress.
• NEVER leave Napper in place when child is in the playard. Only one child can use the Nursery Center at any time.
• ALWAYS ensure that the playard, changing table, and Removable Rock-A-Bye Bassinet are safe by checking regularly, before placing the child in it, that every part is properly and securely in place.
• NEVER leave Bassinet in place when child is in the playard. Only one child can use the Nursery Center at any time.
• ALWAYS remove Parent Organizer and all Bassinets and Changing Table when a child is in the Playard. NEVER use any accessories that entrap the child within the Playard.
• NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts.

Assembly Instructions

IMPORTANT! To ensure safe operation of your playard, please follow these instructions carefully. Please keep these instructions for future reference.

IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are missing or broken.

IMPORTANT! Adult assembly is required.

To Assemble Playard

ATTENTION: Playard must be fully assembled and securely locked before installing or using other accessories.

1. Unzip bag and remove Playard frame (as shown in Figure 1). Undo the fasten straps and set the mattress aside. Do NOT push the center down yet.
2. Top rails must be fully erected before lowering the center. Pull up one rail at a time, holding one hand on each side of the rail and pull up sharply. Do not pull from the middle where the center latch release is located. Ensure both tubes latch in place and each rail is rigid (as shown in Figure 2).
3. Once all four top rails are locked in place, push down on the center handle (as shown in Figure 3a). The center mechanism automatically locks in place. IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and securely in place before use (as shown in Figure 3b).
4. Place the Mattress on the floor of the Playard with the padded side facing up (as shown in Figure 4).
5. Insert the hook & loop fasteners located on the underside of the Mattress through the slots in the floor of each end of the Playard (as shown in Figure 5a). Fasten the hook and loop fasteners to the underside of the Playard floor to prevent the Mattress from moving (as shown in Figure 5b). IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (approx. 45.7 cm or 18 inches) while locking the side rails in place. If the center is not raised, the rails will NOT lock. If you experience difficulty and one side of the rail will lock but the other side will not, unlock the rail by squeezing the release in the center and try again. If you still have difficulty, contact Customer Service at 1-800-328-7363 or visit www.babytrend.com.
6. To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever (as shown in Figure 6).

Folding Playard

7. Release the hook and loop fasteners holding the Mattress from underneath the Playard floor or the Bassinet and set the mattress aside. DO NOT unlock top rails yet; the center of the floor must be raised before top rails will unlock.
8. Rotate the center handle counter-clockwise 90 degrees and raise the center as high as the top rails (as shown in Figure 7). Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch.
9. Locate the rail latch release in the center and bottom side of each rail. Squeeze the lever with two hands until the rail releases the two tubes (as shown in Figure 8a), then push down (as shown in Figure 8b). NOTE: If the top rail(s) do not release completely, DO NOT FORCE! Lift the center of the floor higher. Both tubes must be released for the top rail to fold.
10. Gather four corners and center all together tightly (as shown in Figure 9). Wrap the Mattress around the Playard frame with the padded side facing inward.
11. Secure the hooks and loop fasteners by feeding them through the loops on the end of the Mattress and folding them back onto themselves (as shown in Figure 10). Place the folded Playard into the carry bag so that the handle comes through the opening between each side of the zipper.

To Assemble Bassinet

ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature (See To Assemble Playard section, step 1). You will need to remove the mattress from the bottom of the Playard to use inside your Bassinet.

11. Connect opposing Mattress Support Tubes that are attached to the bottom of the Bassinet (as shown in Figure 11a). Before placing the Mattress into the Bassinet, make sure Mattress Support tubes are connected (as shown in Figure 11b).
12. Position the Bassinet over and down onto the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place (as shown in Figure 12).
13. Place the Mattress into the Bassinet with the padded side facing upward (as shown in Figure 13). NOTE: Fasten tabs underneath the Mattress secure it in place.

To Remove Bassinet: Remove Mattress from Bassinet. Disconnect opposing Mattress Support Tubes. Unsnap all clips and lift Bassinet.

To Assemble Changing Table

ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature (See To Assemble Playard section, step 1).

1. Connect the two Long Curved Bars together (as shown in Figure 14a).
2. Insert the assembled curved bars into the outer sleeve of the Changing Table fabric (as shown in Figure 14b). Slide the Curved Bars around inside the sleeve of the Changing Table.
3. Connect the two Short Bars to each end of the Long Curved Bar (as shown in Figure 14c). Make sure that the knobs are both facing down and in the same direction on each end (as shown in Figure 14d).
4. Insert Connector Knob Prongs into holes located on both corners of the Playard (as shown in Figure 15a).
5. Turn the Connector Knobs counter-clockwise to lock into place (as shown in Figure 15b).
6. Flip Changing Table over onto Playard (as shown in Figure 15c).
7. Secure the two snaps on the flap down onto the Playard (as shown in Figure 15d).
8. Locate the hook and loop fasteners on the bottom of the changing table and on the inside of the side rails of the playard (as shown in Figure 16). IMPORTANT! When the changing table is flipped up into the upper position, the changing table must be secured to the playard frame using the hook and loop fasteners provided.
9. Flip the changing table into its upper position (as shown in Figure 17).
10. Secure the changing table to the playard frame by fastening the hook and loop fasteners on the underside of the changing table to the side rails of the playard frame (as shown in Figure 18).

To Use Changing Table Restraint System:

19. Place child on changing table, making sure hand and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together (as shown in Figure 19a). Tighten strap until it fits snug around child's waist (as shown in Figure 19b). DO NOT OVER TIGHTEN. To remove, unsnap the buckle. ATTENTION: NEVER use changing table if it is damaged or broken.

To Remove Changing Table:

20. Flip Changing Table to the outside of the Playard. Unsnap fabric flap of Changing Table from Playard. Twist Connector Knobs clockwise to unlock (as shown in Figure 20a). Remove Changing Table from Playard (as shown in Figure 20b) and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve.

Parent Organizer Assembly

1. Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it locks into place (as shown in Figure 21a). Diaper Stacker: Skip to next step.
2. Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two connecting clips over an open portion of the top rail of the Playard (as shown in Figure 21b). NOTE: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.

To Assemble Removable Rock-A-Bye Bassinet

ATTENTION: Playard must be fully assembled and securely locked before installing or using Removable Bassinet feature (See To Assemble Playard section, step 1).

1. Pull Removable Bassinet fabric back to access the bottom of the Removable Bassinet. Use the handle to pull the frame supports into the support locks (as shown in Figure 22a). Make sure the frame supports lock and are seated firmly in the support locks (as shown in Figure 22b). NOTE: Use ONLY the handles to move Frame supports. Using your fingers may result in getting pinched.
2. Pull the fabric over the frame and secure fabric with buttons on the sides and front of the frame (as shown in Figure 23).
3. Use the hook and loop fasteners provided to fix mattress into Removable Bassinet (as shown in Figure 24). DO NOT use Removable Bassinet without the provided mattress.
4. Raise the Removable Bassinet handle by pushing the buttons on each side of the handle. Make sure the handle locks into position before using (as shown in Figure 25a). To lower handle, push both buttons on each side of the handle with your fingers while pushing the handle backwards (as shown in Figure 25b).

ATTENTION: DO NOT use Rock-A-Bye bassinet on playard without the bassinet. Bassinet must be fully assembled and securely locked before installing or using the Bassinet feature (See page 8 step 11).

26. To use Removable Bassinet in the Playard, lower Removable Bassinet into the Playard (as shown in Figure 26a). Push down on the front and rear of Removable Bassinet to secure the hooks onto the Playard railing. Button the front and rear strap from Removable Bassinet onto the playard frame (as shown in Figure 26b). DO NOT use Removable Bassinet on Playard without securing the hooks and straps to playard.

Rocker Function

27. Turn Removable Bassinet over and pull rocker feet from the base of the Removable Bassinet (as shown in Figure 27a). Set Removable Bassinet on a flat surface (as shown in Figure 27b). NEVER use Removable Bassinet on raised surface such as Table, Bed or Chair. A fall can occur.

To Fold Removable Rock-A-Bye Bassinet

WARNING: Care must be taken when folding and unfolding to prevent finger entrapment.

CAUTION: Do not allow children near while folding and unfolding.

28. Remove the Removable Bassinet from the Playard and place on a flat surface.
29. Release the canopy fabric and Removable Bassinet fabric from the frame (as shown in Figure 28a).
30. Pull Removable Bassinet fabric back to access the bottom of the Removable Bassinet. Press down on the bottom of one end of the Removable Bassinet and pull up on the handle until the support frame releases from the support lock (as shown in Figure 28b). Repeat for the other side (as shown in Figure 28c).
31. Pull the support frames to the center until the Removable Bassinet folds (as shown in Figure 28d).
32. Lower canopy handle, push both buttons on each side of the handle with your fingers while pushing the handle backwards (as shown in Figure 28e).

Operation

Music Center

WARNING: Keep batteries out of children's reach. Old and new batteries should not be mixed. Alkaline, standard carbon-zinc, and rechargeable nickel-cadmium batteries should not be mixed. Remove batteries before storing music center for a long period of time.

1. The Music Center is designed to be attached to the Playard/Removable Bassinet's long rail (as shown in Figure 29).

Music Operation

30. The Music Center requires 4 AA batteries. Unscrew the battery door screws and pull outward on the battery door. Install batteries as shown. Re-install battery door and secure with screws (as shown in Figure 30).

• To listen to MUSIC, press the MUSIC button. Press the button to change the song.
• To listen to NATURE sounds, press the NATURE button. Press the button to change the sound.
• To listen to SLEEP music, press the SLEEP button. Press the button to change the song.
• These 2 buttons control the unit's volume.
• VIBRATION: To use the VIBRATION, press the VIBRATION button once to activate the speed, press again for faster speed. Press it again to reduce the speed.
• NIGHT LIGHT: To use the night light, press the NIGHT LIGHT button.

Other Information

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada ICES-003 Statement

This Class B digital apparatus complies with Industry Canada Standard ICES-003. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

Maintenance and Cleaning Instructions

Use only household mild soap and warm water. DO NOT USE BLEACH. DO NOT MACHINE WASH.