HOGA TOKYO Overhead Showerhead Set

Introduction

Dear Customer, you have purchased a durable, high-quality product manufactured by HOGA. Before installation, please read through these instructions completely and note the advice provided. These instructions contain important information about installation, settings, and care. Keep these instructions safe and pass them on with the product to any future owners.

Proper Use

This product is suitable for use with instantaneous water heaters. It is not suitable for low-pressure water heaters such as wood or coal burning bath geysers, oil or gas bath geysers, or open electrically heated water tanks. Any use other than described herein or modification to the product is not permitted and may lead to damage to persons or property, with risks of injury and loss of life. The product is intended for personal use only and not for medical or commercial use.

Technical Data

Safety Advice

DANGER OF LOSS OF LIFE AND ACCIDENT TO INFANTS AND CHILDREN!

Never leave children unsupervised with the packaging materials. There is a danger of suffocation. ⚠️

CAUTION! DANGER OF INJURY!

Ensure that all parts are undamaged and correctly assembled. Incorrect assembly or fitting may lead to injury. Damaged parts can adversely affect safety and proper function.

CAUTION - RISK OF DAMAGE!

Please have the installation done by experienced persons only.

CAUTION DANGER OF WATER DAMAGE!

Before installation, ensure there are no water pipes where you intend to drill. Ensure that all seals are correctly seated. Examine the wall before installation and choose suitable installation fixings. The supplied fixings are suitable for ordinary solid masonry walls.

DANGER OF SCALDING!

When setting the hot water temperature, ensure it is not too high. Please note that seals are wear parts and require periodic replacement.

Installation Notes

A 23 mm spanner is required for the installation of the shower hose and the connection hose for the valve. Please do not use a pipe wrench.

Assembly Instructions

Parts List

• Part 1: Shower Arm/Pipe (1x)
• Part 2: Seals/Washers (5x)
• Part 3: Connector for Overhead Shower (1x)
• Part 4: Overhead Shower Head (1x)
• Part 5: Wall Bracket / Hand Shower Holder (2x - one for bar, one for wall mounting)
• Part 6: Hand Shower (1x)
• Part 7: Component of Diverter Assembly (1x)
• Part 8: Metal Shower Hose (150 cm) (1x)
• Part 9: Diverter Valve (1x)
• Part 10: Connection Hose (70 cm) (1x)
• Part 11: Wall Mounting Screws (4x)
• Part 12: Wall Plugs (4x)

Assembly Steps

Diagram A: Overview Depicts the fully assembled HOGA TOKYO Overhead Showerhead Set, with all components numbered for reference.

Diagram B: Mounting Shower Bar to Bracket Shows the shower bar (1) being attached to the wall mounting bracket (5) using screws.

Diagram C: Adjusting Shower Bar Height Illustrates adjusting the vertical position of the shower bar (1) on its bracket (5) by loosening and tightening screws.

Diagram D: Attaching Diverter and Hoses Shows the diverter valve (9) attached to the shower bar (1) and the main shower hose (8) and the shorter connection hose (10) being connected.

Diagram E: Adjusting Hand Shower Holder Height Illustrates moving the hand shower holder (5) up or down the shower bar (1) to adjust its height.

Diagram F: Connecting Connection Hose to Diverter Details connecting the water supply connection hose (10) to the diverter valve's 'INLET' port.

Diagram G: Wall Mounting Shows the shower bar assembly being fixed to the wall using screws (11) and wall plugs (12), with a 5mm clearance indicated between the bar and the wall.

Diagram H: Connecting Hoses to Diverter and Inlet Illustrates connecting the water inlet hose (10) to the water supply and the shower hose (8) to the diverter valve (9), using seals (2) for a watertight connection.

Diagram J: Connecting Hand Shower to Hose Shows the hand shower (6) being connected to the end of the shower hose (8) using a seal (2).

Diagram K: Attaching Overhead Shower Head Depicts the overhead shower head (4) being attached to the shower arm (1) via a connector (3) and seal (2).

Diagram L: Connecting Shower Arm to Diverter Shows the shower arm (1) connecting to the diverter valve (9) with a seal (2).

Diagram (Page 13): Functionality Demonstrates the function of the diverter valve (9) to switch water flow between the overhead shower (4) and the hand shower (6). It also shows how to adjust the spray pattern on both shower heads by rotating parts. ?

Shower Settings

Use the diverter (9) to select the shower mode: overhead shower (4) or hand shower (6). The slope of the overhead shower can be adjusted by the user.

Care Advice

Never use petrol, solvents, harsh cleaners, or hard brushes, as these could damage the product's surface. Clean the product with a soft, damp cloth, using a mild detergent if necessary.

Disposal

The overhead shower set is supplied in robust packaging to protect it from transport damage. The packaging consists of recyclable materials and should be disposed of in an environmentally compatible manner. When the product reaches the end of its useful life, do not discard it with normal household waste. Please contact your local council for information on environmentally compatible disposal.

Warranty

This product underwent strict quality control during manufacture, and HOGA provides a 2-year warranty covering material and manufacturing defects that detrimentally affect its proper operation and intended use. Detrimental effects on functions caused by limescale deposits, incorrect installation, or chemical/mechanical action (e.g., unsuitable cleaning materials or improper handling) are excluded from the warranty. This warranty is valid only with the corresponding purchase receipt.

Service

Should you have reason to claim under the warranty, please contact:

Service Centre details:
Franz Joseph Schütte GmbH
Ringstraße 7
49134 Wallenhorst (Germany)
+49 (0) 54 07 / 87 07 - 0
info@fjschuette.de
www.fjschuette.de

HOGA is available to help with any further questions. Enjoy your new overhead shower set!