Assembly Instructions
KC43150700 Oak Look Corner Bookshelf
Care Instructions
Wipe clean with a soft cloth. Do not use scourers, abrasive materials or chemical solvents. Check and tighten all parts regularly. Store in a dry place and keep away from water and direct sunlight. For indoor and domestic use only.
Warnings
Do not stand or sit on this unit. Do not use until all screws are firmly secured. Use only on a flat surface. Do not drag when moving the product to avoid damaging the joins. Failure to follow these warnings could result in serious injury.
Maximum Safe Load: 2kg/3kg/4kg/5kg per layer.
Hardware List
| Part | Description | Quantity |
|---|---|---|
| a | 4x35mm screw | 23pcs |
| b | Screw | 27pcs |
| c | 4x50mm screw | 4pcs |
| d | 9x9mm dowel/connector | 4pcs |
| e | Wall Anchor | 1 pc |
| f | 4x10mm screw | 1 pc |
| g | 6x30mm screw | 1 pc |
| h | 6x30mm screw | 2pcs |
| i | Connector/Bracket | 4PCS |
Assembly Steps
Note: Do not tighten the screws fully during assembly. Fully tighten screws after the final assembly steps.
Step 1: Identify Parts
Identify all components: two large vertical side panels (labeled 1 and 2), two angled corner side panels (labeled 3 and 4), and four shelves (labeled 5, 6, 7, and 8). Also, gather all hardware items (a-i).
Step 2: Assemble Main Frame
Attach shelves (5, 6, 7, 8) between the two main vertical side panels (1 and 2). Use four 'c' (4x50mm) screws and four 'b' screws for each shelf connection, as indicated in the diagram.
Step 3: Attach Angled Side Panels
Connect the angled corner side panels (3 and 4) to the outer edges of the assembled shelves. The diagram indicates using 'd' (9x9mm) dowels/connectors and 'h' (6x30mm) screws for these attachments.
Step 4: Reinforce Structure
Further secure the bookshelf structure using the remaining hardware: four 'c' (4x50mm) screws, four 'b' screws, four 'd' (9x9mm) dowels/connectors, two 'h' (6x30mm) screws, and four 'i' connectors/brackets. Distribute these as shown in the diagram to reinforce joints.
Step 5: Attach Outer Curved Panels
Attach the outer curved side panels to the sides of the bookshelf. Use eight 'a' (4x35mm) screws and eight 'b' screws for this step, as depicted in the diagram.
Step 6: Secure Top and Bottom
Attach the top and bottom shelves (parts 5 and 6, or as indicated by the diagram's numbering) to the main side panels. Use fourteen 'a' (4x35mm) screws and fourteen 'b' screws for these connections.
Step 7: Install Anti-Tip Hardware
Attach the wall anchor ('e', 1 pc) to the top rear of the bookshelf using one 'a' (4x35mm) screw, one 'f' (4x10mm) screw, and one 'g' (6x30mm) screw. This hardware is crucial for safety and preventing tipping.
Important Safety and Usage Instructions
Wall Anchoring Recommendation
It is strongly recommended that this product is permanently fixed to the wall to prevent tipping. Please seek professional advice if you are in doubt about what fixing device to use. Regularly check that anchors are securely maintained.
Stability Considerations
The stability of tall items may be affected by thick pile carpet or uneven floors. Do not place unanchored televisions on furniture.
Caution: Wall Drilling
For your safety when attaching anchor fixings, please note the following: Check any electrical wires or plumbing inside the wall before drilling any holes. If you are unsure, please seek professional advice from a qualified tradesperson.
