Product Registration for Safety Alert or Recall Only
Vingli uses the information provided on this card to contact customers only if there is a safety alert or recall for this product. Vingli does not sell, rent, or share personal information. To register a product, customers can complete and mail the bottom part of this card, or visit the online registration at: www.vingli.com.
Please visit the online registration at: www.vingli.com. No need to mail.
Manufacturer's Contact Information
DERICK LIMITED
ADD: FLAT/RM 01 11/F HANG SENG CASTLE PEAK RD.BLDG 339 CHEUNG SHA WAN,KL Hong Kong 999077
USA Tel: (732)348-8096
Model Name: MG
Model Number: G666-G
Manufacture Date: 2022-05
KEEP THIS TOP PART FOR YOUR RECORDS. FILL OUT AND RETURN BOTTOM PART THROUGH MAILBOX.
Email: support@vingli.com
Customers are asked to provide Name, Mailing Address (City, State, Zip Code), Telephone Number, and E-mail address, along with Model Name (MG), Model Number (G666-G), and Manufacture Date (2022-05) for product registration.
Thank You for Your Purchase
If customers have difficulty with assembly or find a part missing or damaged, Vingli encourages them to contact for a solution. The Vingli Customer Service team aims to provide satisfaction.
Here is how to connect:
Email: support@vingli.com
Official Website: https://vingli.com/
Before Using Product
Customers should read and follow all instructions carefully to ensure the gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of the child is the customer's responsibility. Please keep these instructions for reference.
Important Safety Information
- The four mounting brackets must be used in securing the gate to the wall. These brackets prevent the gate from dislodging from its opening and becoming unstable.
- If hardware mounting to a surface such as drywall or wood, customers should consult with a professional about installation. Hardware mounting is not suitable for hollow walls or aerated concrete block walls.
Warning
- To prevent serious injury or death, securely install the gate and use according to manufacturer's instructions.
- Never use with a child able to climb over the gate or dislodge/open the gate.
- This product will not necessarily prevent all accidents.
- Keep at least 2 feet from open flame or heat source.
- Never leave child unattended.
- Use only with the locking/latching mechanism securely engaged and on the side away from the child.
- This product is intended for use with children from 6 months up to 24 months of age.
- Hardware is included for use in solid material only, such as wood or metal.
FAQ: Frequently Asked Questions
1. When a replacement is received from Vingli Customer Service, how to replace the plastic joints on the door part?
- Step 1: Take off the balance defective plastic part off the door panel by using a hammer (not included).
- Step 2: Put on the new replacement.
- Step 3: Use a hammer to help the replacement fix more securely.
Visual description: A series of diagrams illustrate the process. The first shows a hammer striking the existing plastic joint to remove it. The second shows the new joint being positioned. The third shows the hammer being used to tap the new joint firmly into place.
2. What to do when the pre-installed V-shaped shrapnel (F) is missing?
Customers should find the 4 spare V-shaped shrapnel parts which come with the package and install them themselves.
Visual description: Diagrams show the V-shaped shrapnel (F) being inserted into a slot on the gate frame, then pushed down until it is flush, indicating proper installation.
3. How to do when the door bottom plastic connector (G) is broken?
- Step 1: Use needle nose pliers to help take off the broken part inside the metal bar.
- Step 2: Position the rod K back on the Upper connector (F or H).
- Step 3: Position the K on G.
- Step 4: Press D and make it fully fix with the door panel.
- Step 5: Put the screw in.
Visual description: A diagram shows the components F/H, K, and G. Arrows indicate the sequence of assembly: K connecting to F/H, then K connecting to G, and finally a screw being inserted to secure the connection.
4. Where to order an extension panel?
Customers can contact Vingli Customer Service for the link or find different sizes listed in their product listing.
Email address: support@vingli.com
Components
Tips: Every package will come with extra 1 PC Door Bottom Plastic Connector(G) and 4 PCS V-shaped Shrapnel (D) as spare parts.
3-Panel Configuration
Visual description: A diagram shows a three-panel safety gate configured in a U-shape, consisting of one door panel and two side panels.
Contains:
- Door Panel: 1
- Side Panel: 2
- Upper Plastic Joints(A): 2
- Lower Plastic Joints(B): 2
- Metal Rod(K): 4
- Wall Mount Bracket(C-1): 4
- Mounting Screws(C-2): 8
- Plastic Expansion Tubes (C-3): 8
5-Panel Configuration
Visual description: A diagram shows a five-panel safety gate configured in a wider U-shape, consisting of one door panel and four side panels.
Contains:
- Door Panel: 1
- Side Panel: 4
- Upper Plastic Joints(A): 4
- Lower Plastic Joints(B): 4
- Metal Rod(K): 6
- Wall Mount Bracket(C-1): 4
- Mounting Screws(C-2): 8
- Plastic Expansion Tubes (C-3): 8
8-Panel Configuration
Visual description: A diagram shows an eight-panel safety gate configured to enclose a larger area, suitable for a play yard. It consists of one door panel and seven side panels.
Contains:
- Door Panel: 1
- Side Panel: 7
- Upper Plastic Joints(A): 6
- Lower Plastic Joints(B): 6
- Metal Rod(K): 8
- Wall Mount Bracket(C-1): 4
- Mounting Screws(C-2): 8
- Plastic Expansion Tubes(C-3): 8
Replacement Parts Available
In the event of any damage or breakage, the following replacement parts are available by contacting Vingli Customer Service.
Visual description: A diagram of the gate with various parts labeled A through K, pointing to specific components. Below the main diagram, individual illustrations of each part are shown with their corresponding labels.
- A: Upper Plastic Joints
- B: Lower Plastic Joints
- C-1: Wall Mount Bracket
- C-2: Mounting Screws
- C-3: Plastic Expansion Tubes
- C-4: Plastic Expansion Tubes (likely a duplicate label for C-3 or a variant)
- D: V-shaped Shrapnel
- E: Door Latch
- F: Door Handle Bottom Connector
- G: Door Bottom Plastic Connector (bottom left & right)
- H: Door Upper Right Plastic Joints
- I: Door Bottom Right Hinge
- J: Bottom Door Latch
- K: Metal Rod
Using the Gate
To open the door:
- Push the door release button backward.
- Lift the door panel upward.
- Swing door open and release button.
Tips: If the door is opened past 90 degrees, it will stay open.
Visual description: A diagram shows a hand pushing a button on the gate handle (labeled 1), and then lifting the gate panel (labeled 2) to open it.
To fold the play yard:
- Loosen all of the locking knobs so the whole gate can move freely and become flexible at the joints.
- If the gate is in a play yard shape, remove one of the upper joints A from the play yard and remove one vertical rod K. This action allows the two plastic joints and the top and bottom of the play yard to be pulled apart.
- Fold and put away.
Care and Maintenance
Customers should periodically check the gate for signs of damage, wear, or missing components. The gate should not be used if any part is missing, worn, or damaged. The gate should be checked regularly to ensure all hardware and mountings are tightened. Abrasive cleaners or bleach should not be used. The gate can be cleaned by sponging with warm water and a mild detergent. In the event of any damage or breakage, Vingli Customer Service can be contacted for replacement parts.
Assembly Process
Step 1. Distinguish Direction
For connectors on the door panel, which are pre-installed, assembly starts from the door panel.
Customers should distinguish each direction of the 4 corner connectors on the door panel. Then, follow the model below to connect side panels with joints:
Connectors can be distinguished by looking at the curve or straight sideline.
When the fence stands, in each panel, the two upper plastic joint A (or bottom plastic joint B) in the horizontal direction should face opposite directions.
Visual description: Diagrams show various orientations of the upper (A) and lower (B) plastic joints, indicating how they should be aligned for proper assembly. Arrows show the direction of the curve or straight sideline for distinguishing orientation. A larger diagram shows a multi-panel gate with arrows indicating the correct opposing directions for the upper and lower joints on each panel.
Each upper joint A should face the same direction as the vertical bottom one B.
Visual description: A series of diagrams illustrate the correct alignment of upper (A) and lower (B) joints, showing how they should be oriented to connect panels, with arrows indicating the direction of connection.
Step 2. Connecting Side Panels
Checking before start:
Pre-installed V-shaped shrapnel (D) are in 4 corners of each panel, with a visible small metal button outside the hole.
Visual description: A close-up diagram shows a V-shaped shrapnel (D) with a small metal button protruding from a hole.
Tips: If the pre-installed V-shaped shrapnel (D) is missing, customers can use the 4 spare parts provided in the package and refer to the FAQ section for installation.
General Process:
- Install the lower plastic joints B on the bottom corner of the panel.
- Position the metal rod K to the B.
- Install the upper plastic joints A on the upper end of K.
- Connect A to the upper corner of the panel.
Visual description: A sequence of diagrams shows the assembly steps: a panel with a lower joint B, then a metal rod K being inserted into B, then an upper joint A being placed on K, and finally A connecting to the upper corner of another panel, forming a connection.
Method for installing upper & bottom plastic joints:
Press the metal button (outer part of V-shaped shrapnel D) and insert into plastic joints. A “Click” sound will confirm proper installation.
Visual description: A three-step diagram shows: 1) pressing the metal button on the V-shaped shrapnel, 2) inserting the plastic joint over the shrapnel, and 3) the joint fully seated with the button depressed, indicating a secure connection.
Disassembly Process
Customers should use an Allen Key (not included) to press down the small metal button and then separate the plastic joint.
Tips: The upper joint should be taken off first, and then the bottom joint.
Visual description: A diagram shows an Allen key being used to press a small metal button on a joint (labeled 2), allowing the joint to be separated from the gate frame (labeled 1). Another diagram shows the upper joint being removed, followed by the lower joint.
