H9S-C Series Intelligent Tracking Selfie Stick

Product Introduction

The H9S-C Series Intelligent Tracking Selfie Stick is designed for hands-free photography and videography, offering advanced tracking capabilities.

Key components include:

• Phone clip: Used to securely hold your smartphone.
• Tracking head: Houses the intelligent tracking camera and recognition camera.
• Tracking camera: The main camera responsible for subject tracking.
• Rocker handle: Allows manual adjustment of the head's position.
• Knobs: Used for tightening and securing components, such as the phone clip.
• Telescopic rod: Extends the reach of the selfie stick for wider shots.
• Support Stand: Provides stability when the stick is placed on a surface, enabling hands-free use.

To install your phone, pull out the phone clip and tighten the knob to secure it. The telescopic rod can be extended by unlocking the lock switch. The support stand can be opened from the bottom. The remote control can be detached by pushing up on it. Ensure the tracking head is unlocked when powering on the device for proper operation.

Remote Control

The remote control facilitates wireless operation of the selfie stick and camera functions:

• Fill Light (Optional): Provides illumination for photos and videos.
• Power button: Turns the remote and connected device on/off.
• Like button: (Functionality may vary by app, typically for app interaction).
• Charging port: For recharging the remote control.
• Page down/Left page/Right page buttons: For navigating camera app functions or controlling playback.
• Indicator light: Shows status such as pairing, charging, or operational mode.
• Recognition camera: Works in conjunction with the tracking head for subject identification.
• Shutter button: To capture photos.
• Sho Video button: To start and stop video recording.

Pairing the Remote Control:

1. Enable Bluetooth on your smartphone.
2. Long press the power button on the remote control to turn it on.
3. On your phone, search for the Bluetooth device named "Selfie" and select it for pairing.
4. Open your camera or video app. A short press of the function button on the remote control will perform corresponding operations (e.g., take photo, start/stop video).
5. To turn off the camera function, press and hold the power button for approximately 2 seconds.

For detailed instructions specific to your phone model, please scan the QR code provided in the original manual.

Intelligent Tracking Head Operation

Ensure the tracking head is unlocked before powering on the device for optimal performance.

1. Long press the power button to turn on the tracking head.
2. Single-click the power button to activate tracking. The indicator light will flash, signaling it's actively searching for a subject.
3. Double-click the power button to enter slow rotation mode. Click the power button again to stop rotation.
4. Triple-click the power button to enter fast rotation mode.
5. Long press the power button to turn off the device.
6. Charging: Connect a USB 5V adapter to the charging port. The red indicator light is on during charging and turns green when charging is complete.

Intelligent Gesture Control

The selfie stick supports gesture control for hands-free operation while powered on:

• [Gesture-Palm]: Hold your palm up for 2 seconds until the indicator light is on to stop tracking.
• [Gesture-OK]: Make an 'OK' gesture (thumb and index finger forming a circle) for 2 seconds until the indicator light is on to start tracking.

Extended Interface

This product features an extendable threaded connector for attaching additional accessories. Align your device with the extended interface and screw it in. Leave a proper gap, then tighten the knob to complete the connection.

Tip: The bearing capacity of the tracking head is limited. Do not install heavy equipment to avoid damage to the device.

Fill Light Operation

If your model includes a fill light:

1. Power on/Mode switching: Click the button to turn on the light. Click again to cycle through different light modes until powered off. Long press the power button to adjust the brightness of the light.
2. Charging: Use a USB 5V adapter to connect to the charging port for charging.

Note: The fill light is an optional feature; please refer to the specific configuration of your purchased product.

Video Tutorials

Detailed video tutorials are available to guide you through setup and usage for both iOS and Android devices. Please scan the respective QR codes provided in the original manual to access these resources.

Fault Resolution

Remote Control Cannot Be Turned On

>>>>> Charge the remote control and try again after charging.

Bluetooth Cannot Be Connected / Fails to Work Properly After Power On

>>>>> Remove the Bluetooth pairing from your phone's settings, restart the Bluetooth remote control, and re-pair the connection.

Android Phone Cannot Take Photos with Remote Control

1. Open your Camera App. Navigate to Settings and change the "Volume Function" to "Take Photo". This should allow you to take photos using the remote control.
2. If the photo button still does not function correctly: Follow the steps in the "Bluetooth Cannot Be Connected" section to re-pair and connect the device.

Target is Lost

When the target is lost, the gimbal will stop, and the indicator light will blink. You can walk back into the field of view of the camera. To ensure recognition accuracy, it is recommended to use the tracker within a range of 1-3 meters.

Notes

• Do not store the product in low-temperature or humid environments.
• Do not expose the product to high temperatures, such as direct sunlight or fire.
• Do not use the product in places where equipment is restricted to avoid violating public codes or regulations.
• This product contains small parts. Please keep it out of the reach of infants and young children to prevent them from swallowing it accidentally.
• The pictures and dimensions shown on the package and manual are for reference only; please refer to the actual product.