Baby Trend Expedition® 2-in-1 Stroller Wagon

Important Information & Safety Warnings

Please read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

⚠️ WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference.

⚠️ WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out, always use the safety harness and ensure that the children are properly positioned according to these instructions.

⚠️ WARNING: Never leave children unattended.

⚠️ WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.

⚠️ CAUTION: NEVER run or jog with this stroller. This stroller is designed for up to 2 children only. Use with more than 2 children may cause an unbalanced condition which can injure/harm your child. Children must be at least 6 months old and be able to sit upright unassisted.

• Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause a hazardous, unstable condition.
• Be certain the stroller is completely opened and locked in place before allowing a child near the stroller.
• The maximum weight that can be carried in the child tray is 5 lbs (2.26 kg).
• The maximum weight that can be carried in the soft parent organizer is 2 lbs (0.90 kg).
• The maximum weight capacity of the stroller is 55 lb (24.94 kg) for each child. The maximum weight capacity of the stroller in combination with any accessories is 110 lbs (49.89 kg) total. Exceeding the weight limit will cause excessive wear and stress on the stroller and may cause a hazardous unstable condition to exist.
• NEVER use the stroller on stairways or escalators.
• NEVER use the stroller with roller skates, in-line skates, skateboards or bicycles.
• NEVER allow your stroller to be used as a toy.
• To clean use only mild household soap or detergent and warm water on a sponge or clean cloth.
• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.
• Discontinue use of stroller should it malfunction or become damaged.

Warranty Information

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within 1 year of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered/removed serial number, invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user.

Customer Service Department can be contacted at 1 (800) 328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Please visit babytrend.com/pages/limited-warranty for complete warranty details.

Parts Identification

Check that you have all the parts for this model before assembling the stroller.

• Canopy with Mosquito Net (Dosel con Mosquitera)
• Soft Parent Organizer (Organizador flexible para padres)
• Child Tray (Bandeja para niños)
• Front Wheels (Ruedas delantera)
• Rear Axle and (2) Wheels (Eje trasero y (2) Ruedas)
• Wagon Frame (Marco de vagón)
• Car seat adapter - fabric cover (visit babytrend.com for compatibility chart) (Adaptador de la sillita para el automóvil - Cubierta de tela)
• Stroller Board / Ride-On Board Accessory (Sold Separately visit babytrend.com) (Tablero De Cochecito / Ride-On Tablero Accesorio)

Assembly Instructions

Frame Setup

To attach the wheels, unfold stroller as described in the following section:

1. Release the fold latch. (Refer to Figure 1a).
2. Unfold the stroller frame by pulling the stroller handle upward until it clicks into the locked position. (Refer to Figure 1b).
3. Check the RED indicator on the handle. It will not be visible when the stroller is fully open. If the RED indicator is visible, check that the open position lock is engaged before continuing. (Refer to Figure 1c).

Front Wheels

2. Insert the front wheel axle pin into the wheel hub until the wheel locks firmly into place. Repeat on the other side. (Refer to Figure 2a).
3. NOTE: Pull on the wheel assembly to ensure that it is securely attached to the stroller.

Rear Axle-Wheels

Attach the rear axle assembly and wheels as follows:

3. Position the stroller with the rear leg tubes facing upward. Place the rear axle with wheels over the rear legs and apply downward pressure on both sides. Ensure both sides lock into place. (Refer to Figure 3a).

Soft Parent Organizer

⚠️ WARNING: Do not place hot liquids or more than 2 lb. (0.90kg) pounds in the parent tray. Serious burns or unstable conditions can result.

4. Strap In The Soft Parent Organizer: Use the hook and loop to hang the soft parent organizer onto the stroller handle. Follow illustrations 1-3 (Refer to Figure 4a). Be sure to fasten tightly.

Child Tray

⚠️ WARNING: Do not place hot liquids or more than 5 pounds in the child tray. Serious burns or unstable conditions could result.

5. Attach child tray by lining up the corresponding slots located on the stroller frame. Slide down into position until locked into place. (Refer to Figure 5a).
6. NOTE: Check to make sure the child tray is secure before using.

Canopy

6. To install the canopy: Add the canopy frame into the designated slots located on the child tray. (Refer to Figure 6a).
7. To open the canopy: Behind the main fold mechanism, use the strap and snap closure to anchor the canopy. Firmly spread out both sides of the canopy. (Refer to Figure 6b).
8. Install mosquito net: Unzip and pull out the net from the storage pocket. Stretch the net around the top edge of the frame and hook each corner to the circle tabs. Repeat for the other side and ensure to hook the net to all 4 tabs. (Refer to Figure 6c).
9. To store away the mosquito net: Lift the mosquito net at the elastic end and start to roll toward the canopy. Locate the zipper attached to the canopy end and connect the zipper to the track. Continue to tuck the canopy into the pocket while zipping the pocket closed. (Refer to Figure 6d). NOTE: Tuck and Zip in sections.
10. To remove the canopy: Press the tab on each end of the canopy, and lift up the entire canopy from the bottom ends slots of the child tray. (Refer to Figure 6e).
11. To remove the child tray: Push the tabs outward and pull out the child tray. (Refer to Figure 6f). NOTE: The canopy may also be installed without the child tray. Insert the ends into holes.

Pull Handle Storage

7. TO USE THE HANDLE: Locate the handle underneath the frame and press the release button to unlatch. Pull the bar completely out of the frame. (Refer to Figure 7a). Rotate up to the desired position. (Refer to Figure 7b).
8. TO PUT IT AWAY: Reverse step (Refer to Figure 7a). Ensure to push the handle completely in until it clicks into position. NOTE: Ensure the handle is resting on the storage hooks. (Refer to Figure 7c).

Folding the Stroller

⚠️ WARNING: Care must be taken when folding the stroller to prevent finger entrapment.

⚠️ CAUTION: Do not allow children near stroller while folding.

8. Close the canopy by reversing (Refer to Figure 6b).
9. To use the double lock feature: (1) push the safety lock up. (2) Lift up the trigger to hold the safety lock into place. (3) Pull both triggers together. (Refer to Figure 8a).
10. Push down on the stroller handle until the stroller is completely folded. Ensure the fold latch clicks and secures the stroller closed. (Refer to Figure 8b).

Unfolding the Stroller

9. Release the fold latch. (Refer to Figure 9a).
10. Unfold the stroller frame by pulling the stroller handle upward until it clicks into the locked position. (Refer to Figure 9b).
11. The RED indicator on the handle will not be visible when the stroller is fully open. If the RED indicator is visible, check that the open position lock is engaged before continuing.

Safety Harness Usage

⚠️ WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness.

⚠️ STRANGULATION HAZARD: Child can strangle in loose straps. Never leave child in seat when straps are loose or undone.

10. The child tray is not designed to hold the child in the stroller. Stay near and watch child during use. NEVER leave child unattended.
11. Place the crotch strap between your child's legs. Insert the Harness Buckles into the Center Clasp with the Button.
12. NOTE: Only use top slots with Baby Trend Seat 2 Mat accessory (sold separately). Adjust waist straps for your child's comfort and safety by sliding buckles in either direction. Safety straps are to fit snug around your child. (Refer to Figure 10a).

Releasing Safety Belt

11. Push Button on Center Clasp; the two Harness Buckles will pop free. (Refer to Figure 11a).

Brakes

⚠️ WARNING: Always set brakes when the stroller is not being pushed so that the stroller will not roll away. NEVER leave stroller unattended on a hill or incline as the stroller may slide down the hill.

12. To engage brakes, apply light downward pressure to the brake lever located on each rear wheel. The stroller may require slight forward or rearward movement in order to line up the teeth on the brake with each wheel brake cluster. (Refer to Figure 12a).
13. NOTE: Check that the stroller will not move and that both brakes are properly applied.
14. To release, gently lift up on the brake lever.

Car Seat Adapter

⚠️ WARNING: For maximum weight used in the adapter, refer to the manual of the car seat it will attach to. Prevent serious injury or death from falls, ensure car seat adapter is securely attached to the stroller frame before use. Tray and/or Canopy CANNOT be used with the car seat adapter.

⚠️ CAUTION: Avoid serious injury from falling, always use the safety belt to secure car seat to stroller.

Always remove the child tray and canopy from the wagon to install the adapter. See pages 11 to 13.

13. Unfold the adapter and place it on a flat surface. (Refer to Figure 13a). Connect both ends of the adapter bars together as shown. (Refer to Figure 13b).
14. NOTE: Ensure both pins click into the holes. Flip the adapter. (Refer to Figure 13c).
15. Open the clips on both sides of the adapter, open the flaps on the wagon cover to expose the bar connection. (Refer to Figure 13e).
16. Face the front of the adapter to the front of the wagon. Align the clips to the bar as you press them into place. (Refer to Figure 13f).
17. Close the clips firmly from the inside with your thumbs and check that it is secured into the frame. (Refer to Figure 13g).

Adapter Removal

14. REMOVAL: To remove the adapter, wrap your thumbs over the wagon frame and use all your other fingers to apply pressure on the clip to release it from the bar. (Refer to Figure 14).
15. NOTE: Refer to pages 29 and 30 for car seat installation.

Infant Car Seat Installation

INFANT CAR SEAT Sold separately

15. Place the car seat onto the Car Seat Adapter. The front of the car seat should be facing the same direction as the stroller wagon handle. Ensure the car seat stoppers are resting on the Adapter Bars. (Refer to Figure 15a).
16. Strap the Safety Belts through the Belt Path on the Car Seat and connect the buckles together. (Refer to Figure 15b). Tighten the strap so it fits snugly and the car seat is secured to the frame. (Refer to Figure 15c).
17. NOTE: The Safety Belt MUST ALWAYS be installed through the Belt Path before using this product.
18. REMOVAL: Release the safety strap (Refer to Figure 15d), reverse step 15 and then follow step 14.

Maintenance and Care

Wagon Fabric

16. To detach the fabric: for cleaning or replacement, unzip from the front and rear of the wagon frame. (Refer to Figure 16a).
17. Through the pocket opening, remove the D-Rings straps from the fabric near the bottom front and rear frames to unthread the harness straps. (Refer to Figure 16b). Remove the screws on the underside of the frame. (Refer to Figure 16c).
18. To reattach the fabric: ensure that the fabric is realigned to the corresponding front and rear end frames.
19. Through the pocket opening, Insert the D-Ring straps through the slots. The straps must be secured completely with the D-Ring. (Refer to Figure 16b).
20. To ensure the fabric is securely attached, the zippers should be zipped and the hook and loop fasteners are attached. (Refer to Figure 16a).
21. NOTE: Check for worn parts, torn material, or stitching on a regular basis. Replace or repair parts as needed.

Rear Axle Wheel Removal

17. To release the entire rear wheel assembly, push in the rear wheel release. The wheel easily detaches from the bushing. (Refer to Figure 17a).
18. If replacing the rear axle, press the pin on each side behind the wheel hub. Pull the rear axle out from the hub. (Refer to Figure 17b).

Adapter Fabric

18. Use the pin to separate the frame, undo the hook and loop fasteners. Slide out the pre sewn panels from the adapter bar to remove the fabric. (Refer to Figure 18a).
19. To reattach, slide in the pre sewn panels and connect the frame parts. Subsequently hook and loop the panels over the bar to secure the fabric. (Refer to Figure 18b). NOTE: Ensure to and connect the frame parts using the pins.

Care and Maintenance

• Cleaning Seat Pad: Spot clean only - Surface wash small spots with mild solution of soap and water. Rinse with water to remove soap solution. Wipe or air dry.
• Cleaning Stroller: Surface wash stroller frame, plastic parts and fabric with mild solution of soap and water. Wipe surfaces with water to remove soap solution. Wipe or air dry.
• Check your stroller for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.

Contact Baby Trend Customer Service:

The Customer Service Department can be contacted at 1 (800) 328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®.