Rohnson Mamba RM-05 Robotic Vacuum Cleaner

Introduction

Thanks for purchasing a Rohnson robot vacuum cleaner. This manual provides instructions for setup, operation, and maintenance of your Mamba RM-05.

Important Note: To activate the vacuum cleaner, lift the magnetic cover and set the main switch to the 'I' position. Then, press and hold the HOME and POWER buttons until you hear 'Start network configuration'. The Wi-Fi LED will blink during connection and remain steady upon completion.

Note: Rohnson reserves the right to update the app and software. The final interface is subject to the actual product.

Safety Information

This product is intended exclusively for domestic cleaning of washable floor coverings and carpets. Never use the robot outdoors, on balconies, or terraces. It is not intended for commercial or industrial areas.

• Never climb or sit on the robot or the charging station.
• Use only recommended cleaning agents to avoid damaging the robot or station.
• Do not place objects in the station's cleaning part.
• Always clean the robot and station when switched off.
• Before first use, remove all loose cables from the room to prevent entanglement.
• The robot and station are not toys. Keep children and pets away during operation.
• Do not allow the robot to suck in burning objects (e.g., cigarette butts).
• Do not use the product at high temperatures.
• Avoid touching rotating brushes during cleaning to prevent injury.
• Remove sharp objects (glass, nails) from the floor before cleaning.
• Ensure the floor is dry; water can damage the robot.
• Place the station on a flat floor, away from heat and water sources.
• Never lift the robot by its moving parts.
• Remove fragile valuables from the room to prevent damage.
• Use the product only as per this manual. The manufacturer is not liable for injuries from improper use.
• The robot may only be charged at the original station.
• Never disassemble or modify the battery.
• If not using the station for a long time, unplug the power cable.
• Dispose of used batteries only in designated areas.
• Always use original batteries, cables, and the station.
• Clean the robot and station with a dry cloth only.
• Ensure your outlet voltage matches the station's voltage.
• Turn off the robot and station before transporting. Use original packaging if possible.
• Use only the original cable to connect the station to the socket to prevent overheating or fire.
• Never power the station with a current converter, as this voids the warranty.
• Never use damaged cables. Contact customer service if cables show damage.
• If the robot is stored for a long time, fully charge it, turn it off, and store it in a cool, dry place. Recharge at least every 3 months to maintain battery health.

Laser Safety

The laser sensor meets first-class laser product standards (EC 60825-1:2014) and emits no harmful radiation.

Warning

This product is for use by children over 8 years of age. Those with less experience should use it under adult supervision. Cleaning and maintenance should not be performed by children without adult supervision.

Description of the Vacuum Cleaner

The robot features a magnetic top cover, Wi-Fi indicator light, bumper, and 3D Laser Action obstacle recognition. It also has a camera (must be in 'on' position to use). Sensors are located for precise cleaning along walls.

Buttons:

• HOME button: Returns the robot to the station for charging. Press and hold for 10 seconds to restore factory settings.
• Start/Stop button: Press to start/stop cleaning. Press and hold for 3 seconds to interrupt the current program.
• Start pairing: Press and hold both HOME and START/STOP buttons simultaneously for 3 seconds.

The robot has a main switch, waste container fuse, service port, camera switch (must be 'on' to use video camera), and laser lidar.

The underside of the robot includes side brushes, fall sensors, ultrasonic sensors, front wheel, robot information area, Airmax main brush, main wheels, main brush cover fuse, and mops.

The dust tank includes a dust tank opening safety, HEPA filter, and a filter with a grid. The station has a water refill valve, charging contacts, and a hole for automatic dirt extraction. It also includes a washable filter.

Installation of Cleaning Station

1. Place the station on a firm, level floor (not carpet).
2. Connect the power cable and check that the display lights up. Wind excess cable onto the holder on the back of the station.

Location of the Cleaning Station

Place the station on a solid, level floor (wood, tiles) with its back to the wall. Ensure no obstacles are within 0.5 meters in all directions. A good Wi-Fi signal is necessary for app functionality. Plug the power cord into the outlet.

• TIP: A freely laid cable can be wound by the robot, causing it to move or disconnect from power.
• Error lights on the station will appear red and remain lit.
• Always place the station indoors, on a flat floor, away from flame or heat sources.
• Do not place the station in direct sunlight or obstruct its signal transmission, as this may prevent the robot from finding it.
• Do not use the station without the water containers, dirt cup, and filter.
• Perform regular maintenance and clean the station with a dry cloth.
• The presence of a small amount of water is normal due to factory checks.

Power On and Charge

Remove the robot's upper cover and transport foam. Switch the main switch to 'I'. Wait for the Start/Stop button to stop flashing and remain lit, indicating the robot is ready. Switching the main switch to '0' turns off the robot immediately and prevents charging. Place the robot in the station to charge. The robot has a built-in Li-ion battery and should be kept fully charged for optimal performance.

TIP: If the robot cannot be started due to low battery, insert it into the station manually.

Turn On Wi-Fi

Press and hold the START/STOP and HOME buttons together for 3 seconds until you hear 'Start network configuration' and the Wi-Fi light flashes. The robot is now in pairing mode.

Wi-Fi Light Status:

• Off: Wi-Fi function is turned off.
• Flashes slowly: Robot is in pairing mode.
• On: Robot is connected to Wi-Fi.

TIP: If the robot disconnects from Wi-Fi (e.g., due to router changes), reconnect it from the beginning.

Adding a Bot to Your App

Open the Rohnson Link app, press the '+' icon and 'Add device' on the home page. Follow the in-app instructions to pair the robot.

TIP:

• Pairing processes may vary slightly with app updates; always follow current instructions.
• Always use 2.4GHz Wi-Fi.
• If the robot does not connect within 2 minutes, Wi-Fi will turn off automatically. Try activating Wi-Fi again.

Filling the Water Tank

Remove the water tank from the station, open the top cover, and fill with clean water up to the MAX mark. You can add approximately 10ml of mild cleaner. Close the tank and return it to the station.

The dirty water tank fills gradually with pumped water after mop washing. Empty it when full.

The robot has an internal water tank filled automatically from the station's tank.

TIP:

• Never use cleaning agents other than those recommended by the manufacturer to prevent corrosion.
• Do not add excessive detergent, as it can cause wheel slippage and reduce cleaning efficiency.
• Never fill the tank with hot water, as it can deform the tank.
• Wipe any water drops in the station with a dry cloth after removing the tank.

Vacuuming and Mopping

The RM-05 can vacuum, mop, or combine both modes. Settings are available in the mobile application. Ensure the station has water in the clean water tank and a dust bag installed before starting.

The default mode is Vacuuming and mopping. You can select different modes in the app. If 'Wipe' or 'Vacuum and wipe' is selected, the station automatically adds water to the integrated tank and wets the mops.

During mopping, the robot washes mops at set intervals. After cleaning, it sucks dirt into the station's dust bag, washes the mops, and dries them.

TIP: For the first use, it is recommended to let the robot vacuum twice before wiping.

Cleaning Process Details

Press the start button; the robot plans its route based on the saved map. It vacuums and wipes edges, then the room interior. The robot automatically returns to the station to wash mops and add water for optimal results, or you can set a washing interval in the app.

If the robot encounters carpet during mopping, it lifts the mop (up to 1.5 cm) to prevent the carpet from getting wet.

TIP:

• Ensure the robot can return to the station without issues to wash mops and refill water. Never move the station during cleaning.
• During the first cleaning, monitor the robot and assist if needed. Fully charge a dead battery before starting.
• Remove cables and objects that could be dragged or damaged before cleaning.

If the battery runs out, the robot will automatically return to charge and then resume cleaning from where it left off (this function can be activated in the app).

Cleaning Settings Options in the Mobile Application

Cleaning Modes

• SWEEP ONLY MODE
• MOP ONLY MODE
• SWEEP AND MOP
• SWEEPING WHILE MOPPING

The Sweep and Mop program is suitable for heavily soiled surfaces.

Sweeping Programs

• ECO CLEAN
• STANDARD
• CLEAN
• STRONG CLEAN
• MAX CLEAN

Intensity of Floor Soaking During Mopping

• LOW
• MIDDLE
• HIGH

Frequency of Washing Mops During Mopping

• EVERY 10 MIN
• EVERY 15 MIN
• EVERY 20 MIN

Pause

Pressing the button during cleaning interrupts the program. Pressing again resumes cleaning. Pressing the button during cleaning also returns the robot to the station to start charging.

Sleep Mode

If the robot is inactive for over 10 minutes, it enters sleep mode, and station buttons turn off. Press any button to activate it.

Advanced Functions

Do Not Disturb Mode

Set this mode in the mobile application to prevent the robot from cleaning during specified periods.

Child Lock

Activate by pressing and holding the Start/Stop and Home buttons on the station for 6 seconds. It can also be activated in the app. When active, robot and station buttons will not respond.

Restarting the Robot

If the robot is unresponsive or cannot be stopped, turn it off and on again using the main switch.

Reset to Factory Setting

If the robot malfunctions after restarting, restore factory settings by pressing and holding the button for 10 seconds until a beep is heard, indicating the reset process has started. All settings (like cleaning timer or Wi-Fi) will be deleted.

Charging

After cleaning, the robot automatically returns to the station to charge. The indicator light turns on and off during charging.

TIP: If the robot stops cleaning outside the station, return it manually.

Cleaning Upstairs

For cleaning on different floors, it's recommended to move both the robot and the cleaning station. If moving only the robot, remember it's designed for station cooperation. For mopping programs, the station must be nearby to wet/refill mops.

If the robot is on a floor without a station, select vacuuming-only programs. For wiping programs without a station, follow these steps:

1. Set the mopping program and longest mop soaking interval in the app.
2. Place the robot in the cleaning station.
3. Start cleanup; the robot adds water and moistens mops. Immediately pause cleaning as it leaves the station.
4. Move the robot to the desired floor.
5. Resume cleaning. This cleaning session should not exceed 20 minutes, after which the robot will seek the station. If it cannot find it, it will continue, but mop moisture will decrease.
6. After cleaning, return the robot to the station and command it to clean and dry the mops.

Introduction to the Application Features

Cleaning Map

Manage and view cleaning routes, select zones, and edit maps. Multiple maps can be saved; each newly loaded map must be saved to prevent loss.

Individual Cleaning Modes

Includes scheduled cleaning, zone cleaning, map division, remote control, no-go zones, and virtual walls.

Cleaning Mode Settings

Configure cleaning modes, suction intensity, and floor wetting intensity.

Scheduled Cleaning Settings

The robot uses the mobile device's time. Ensure the time zone is correctly set in your router. Set desired cleaning times and repetition days. Notifications for scheduled cleaning can be activated. Scheduled cleaning will not occur if 'DO NOT DISTURB' is active.

Other Functions

Language settings, do not disturb mode.

Robot Information

Access cleaning history, battery status, and maintenance logs.

TIP: Features may vary due to app updates.

Routine Maintenance

Regular maintenance ensures optimal performance. Refer to the table below for recommended intervals.

Main Brush Maintenance

1. Turn the robot over and press the latches on the main brush cover to release it.
2. Remove the main brush, slide out its bearing, and loosen the brush ends. Remove tangled hair and debris.
3. Put the main brush back into the robot.
4. Replace the main brush cover.

TIP: Clean the main brush with a damp cloth; avoid aggressive cleaners.

Side Brush Maintenance

1. Turn the robot over and loosen the side brush screw.
2. Remove the brush, clean it, and reattach it, tightening the screw.

Front Wheel Maintenance

1. Pop out the front wheel using a small screwdriver or tool. (Front wheel carrier cannot be removed).
2. Rinse the front wheel under water, remove hair and dirt, dry it, and reinsert it into the carrier.

Main Wheels Maintenance

Wipe both wheels with a soft, dry cloth.

Waste Container Maintenance

1. Remove the upper magnetic cover of the robot and take out the waste container. Clean it regularly as dirt is sucked into the station's dust bag. Check for blockages.
2. Open the waste container and empty the dirt.
3. Rinse the waste container with clean water and pour out the dirty water.
4. Allow the container and filter to dry.

TIP: Do not add detergents to the waste container, as this can clog the air filter.

Washable HEPA Filter Maintenance

1. Open the HEPA filter cover and remove the filter.
2. Rinse the filter repeatedly to remove dirt.
3. Let the filter dry for 24 hours before putting it back.

TIP: Do not touch the filter surface with hands, brushes, or sharp objects to avoid damage.

Mops Maintenance

1. Remove mops from holders. Mops are washed and dried after each cleaning.
2. Rinse the mops and let them dry.
3. Place the mops back on their holders.

TIP: A dirty mop affects wiping quality; check their condition before use.

Robot Sensors Maintenance

Clean and wipe sensors with a dry, soft cloth:

• Front sensor (station search, obstacle sensor, camera)
• Rear sensor (station search, charging contacts)
• Right cleaning sensor (along the wall)
• Bottom sensor (carpet detection, fall sensors)

Change Station Location

To move the station, grasp it by the handle on the back and the inner part of the front. Lift carefully. Never lift by the bottom to avoid it falling.

Water Tank Maintenance

Change water in the tank regularly. Open the top cover, pour out dirty water, add clean water to the MAX mark, close the tank, and return it to the station.

Cleanser: Use approximately 10ml of mild cleanser with clean water.

TIP: Too much cleaner can cause wheel slippage and affect quality.

Charging Contacts Maintenance

Wipe the charging contacts of the station with a dry, soft cloth.

Cleaning the Cleaning Dock

Clean the cleaning container with the included brush and wipe with a dry cloth.

Cleaning the Filter of the Tank for Clean Water

1. Open the container cover, remove the suction part, small cover, and filter.
2. Rinse with clean water and return to its place.

Replacement of the Dirt Dust Bag

TIP: Replace dirt bags regularly.

1. Open the top cover of the waste container where the dust bag is located.
2. Slide the bag vertically to remove it.
3. Clean the bag container edges with a dry cloth, insert the new bag into the groove, and press into place.
4. Close the top lid securely.

TIP: Ensure the new dirt bag is inserted correctly to prevent leaks. Close the old bag to prevent dirt escape.

Cleaning the Base Clip in the Cleaning Container

1. Pull the base clip outside.
2. Rinse it with clean water.
3. Slide the cleaned base clip back into place.

Technical Parameters

Information About Environmental Protection

This section concerns the environmental battery disposal process, intended for product liquidation. The built-in Li-ion battery contains chemicals harmful to the environment. When disposing of the product, remove the battery and hand it over to a designated collection point or a container for old batteries.

Troubleshooting

The Robot Reports an Error

If the robot's indicator light flashes red and a voice error message is heard, follow the message or the in-app troubleshooting guide. If there is no activity for 10 minutes during an error, the robot enters sleep mode. Attempting to return the robot to the station during an error will terminate the current program.

Station Error

If the station indicator lights red and a voice error message is heard, follow the station's message or the in-app guide. If the error persists, contact customer service. If the station is unpaired, the START/PAUSE light will flash, and the robot will be uncontrollable. Re-pair the station by placing the robot in it, opening the waste chamber, and pushing the dust bag upwards until a beep is heard. Then, press and hold the START/PAUSE button on the station until another beep. Reinsert the dust bag handle and close the chamber. The START/PAUSE light should remain on if pairing is successful.

Problem Solving Table

EU Declaration of Conformity

Manufacturer: Xiamen Lynkbey Robot Ltd Company. Model: RM-05. Declares conformity with relevant Union Harmonization Legislations: RE Directive, Low Voltage Directive, EMC Directive, RoHS.

Harmonized standards applied include those for Health and Safety, Electromagnetic Compatibility, Radio Frequency Spectrum Usage, and Low Voltage Directive compliance.

A recognized third-party organization (Eurofins Electrical Testing Service) performed conformity assessment and issued an EU-type examination certificate.

Radio Equipment Details: Operates on 2.4 GHz band with maximum radiotelephone power of 19.75 dBm. WIFI Specification: Model 6223A-SRD, Standard IEEE 802.11 b/g/n, Antenna Type PCB, Max Transmitted Power 20 dBm. Operating Temperature: -20°C~85°C. Power input: DC 3V-3.6V.