BIGBIG WON Blitz Game Controller User Manual

01. Parts Identification

The BIGBIG WON Blitz controller features the following components:

• Left Joystick
• Directional Pad (Cross Button)
• Left Light
• M4 Button
• FN Button
• Pairing Button
• A/B/X/Y Buttons
• RS (Right Stick)
• Right Joystick
• Right Light
• Macro Record Button
• M3 Button
• ZR Button
• M2 Button
• M1 Button
• Type-C Cable Port

Package Contents:

• Wireless Game Handle *1
• Manual *1
• Certificate of Qualification *1
• Data Cable *1

Supported Platforms:

• Switch
• Win10/11
• Android
• iOS

Diagram Description: A visual representation of the controller shows the layout of joysticks, buttons, and ports. Key elements include the Left and Right Joysticks, Directional Pad, A/B/X/Y buttons, M1-M4 buttons, FN button, Pairing button, Macro Record button, RS (Right Stick), ZR button, Left and Right Lights, and the Type-C port.

02. Power On/Off

Press and hold the [HOME button] for 3 seconds to turn the controller on or off.

03. Connection

This controller supports two connection methods: Bluetooth and wired.

Bluetooth Connection:

After powering on the controller, press and hold the [Pairing button] on the top for 3 seconds. The [HOME button] light will flash, indicating pairing has started. The [HOME button] light will remain solid upon successful connection. (In Switch mode, the specific channel light that illuminates depends on the connection order with the console.)

Wired Connection:

After powering on the controller, connect it to the console using the Type-C cable.

Important Notes:

• This controller supports both Switch and Xinput modes. After connecting to a console, you must switch to the corresponding mode for proper operation. The default mode is Switch mode.
• Steam Platform: In Steam software, navigate to "Settings - Controller - General Controller Settings" and select "Xbox Configuration Support". Otherwise, the game may not recognize the controller.
• Switch Platform: After connecting to Switch via wire, enable "Settings - Controllers and Sensors - Pro Controller Wired Communication".

04. Mode Switching

This controller supports both Switch mode and Xinput mode. To ensure proper operation after connection, you must switch to the corresponding mode. The settings are as follows:

• Switch Mode: Press and hold the A button + [HOME button] for 3 seconds until the [HOME button] indicator light turns red.
• Xinput Mode: Press and hold the B button + [HOME button] for 3 seconds until the [HOME button] indicator light turns green.

Note: To connect to iOS and Android platforms via Bluetooth, you must switch to Xinput mode.

05. Button Mapping

This controller includes 4 programmable buttons (M1/M2/M3/M4) that support button mapping.

• Mapping Setup: Press and hold the desired M1/M2/M3/M4 button, then press the [FN button]. The FN indicator light will flash, indicating entry into mapping mode.
• Press the front button you wish to map to M1/M2/M3/M4 again. The FN indicator light will flash twice, confirming successful mapping.
• Clear Single Mapping: Press and hold the button (M1/M2/M3/M4) for which you want to clear the mapping, then double-click the [FN button]. The FN indicator light will flash twice, indicating the mapping for that button has been cleared.
• Clear All Mappings: Double-click the [FN button]. The FN indicator light will flash twice, indicating all button mappings have been cleared.

06. Turbo Function

This controller supports button mapping for Turbo function on A/B/X/Y, Directional Pad (Up/Down/Left/Right), L/R/ZL/ZR, and M1/M2/M3/M4 buttons, totaling 16 buttons.

• Turbo Setup: Press and hold the desired button, then press the [FN button]. The FN indicator light will flash twice, indicating successful activation. (During Turbo operation, the FN indicator light will flash according to the turbo frequency.)
• Clear Single Turbo: Press and hold the button for which you want to clear the Turbo function, then double-click the [FN button]. The FN indicator light will flash twice, indicating the Turbo function for that button has been cleared.
• Clear All Turbo Buttons: Double-click the [FN button]. The FN indicator light will flash twice, indicating the Turbo function for all buttons has been cleared.
• Turbo Frequency: Press FN + [Left arrow button] to switch between three frequencies: 5/s, 10/s, and 20/s. The default is 5/s.

07. Macro Recording

This controller features a macro recording function. Each macro set must bind a back button (M1/M2/M3/M4) as the trigger switch. The buttons that can be recorded are A/B/X/Y, Directional Pad (Up/Down/Left/Right), LT/RT/LB/RB, RS/LS, and the 8 directions of the joysticks. The setup method is as follows:

• Macro Recording: Press and hold the [Plus button] + (M1/M2/M3/M4) for 3 seconds. The FN indicator light will flash, indicating macro recording has started. Press controller buttons to record the macro. After recording, click the [FN button]. The FN indicator light will flash twice, indicating recording is complete. (During macro playback, the FN indicator light will flash slowly until the macro recording is finished.)
• Clear Single Macro: Press and hold the button (M1/M2/M3/M4) for which you want to clear the macro, then double-click the [FN button]. The FN indicator light will flash twice, indicating the macro setting for that button has been cleared.
• Clear All Macros: Double-click the [FN button]. The FN indicator light will flash twice, indicating the macro setting for all buttons has been cleared.

08. Onboard Setting Switching

Switch Mode: First, click the [FN button]. The channel indicator light will change from red to white, entering setting switching mode. In this mode, the 4 indicator lights represent 4 different onboard setting values.

Click the [FN button] again to cycle through the settings. The indicator lights will change in order from top to bottom, showing the currently selected onboard setting. If no setting change is made within 5 seconds, the setting switching mode will automatically exit, and the indicator light will change from white back to red, returning to the channel display.

Xinput Mode: This mode does not have a channel notification function. The indicator light will arbitrarily display white to show the current onboard setting value. In this mode, clicking the [FN button] directly changes the settings.

09. Joystick Dead Zone

This controller has a default joystick dead zone setting. Users requiring a 0 dead zone can press FN + [Left Stick Down] and [Right Stick Down] (LS/RS) to switch between two gears for the left and right joysticks' dead zones: 0 and 10.

Note: A 0 dead zone for joysticks offers higher control accuracy but may cause drift in games that do not have a dead zone.

10. Joystick Calibration

If the joystick drifts or does not reach its maximum range, you can calibrate the joystick as follows:

1. Press and hold the [Plus button] and [Minus button] simultaneously for 3 seconds. The left and right lights will flash orange simultaneously, indicating entry into calibration mode.
2. Push the joysticks to their full extent and rotate them at a constant speed. Repeat this 3-5 times.
3. Finally, press and hold the [Plus button] and [Minus button] simultaneously. The left and right lights will flash twice, indicating calibration is complete.

11. Gyroscope Calibration

If the gyroscope on the controller exhibits drift, you can calibrate it by following these steps:

1. Place the controller on a horizontal desk. Press and hold the [Plus button] and the [Screenshot button] simultaneously. The left and right lights will flash purple, indicating entry into calibration mode.
2. After a moment, the left and right lights will flash purple twice, indicating calibration is complete.

12. Vibration Control

This controller features 4-level vibration control. The operation method is as follows:

• Press FN + [Right arrow button] to adjust the vibration intensity of the trigger motor. It can be controlled in four modes: Strong, Medium, Weak, and Off.

13. Battery Description

When the battery is low, the lights on both sides of the controller will flash twice per second for 10 times, and an alert will sound every 5 minutes. When a power supply is connected, the controller light flashing red indicates it is charging. Wait until the battery is fully charged, and the charging light turns off, the lights will return to their normal state.

Charger Pad: In standby mode, the pad has no lighting indication. When the controller is connected to the pad, the pad's RGB indicator light will alternate through seven colors, indicating the controller is charging. When the pad light is solid RGB green, it indicates the controller's battery is fully charged.

14. Detailed Function Operation Description

Visit the official website for tutorials: BIGBIG WON Official Website Support Page.

URL: https://www.bigbigwon.cn/support

15. Your Rights

The product warranty period is 12 months from the date of purchase.

Video tutorials, upgrade tools, and digital manuals are available. BIGBIG WON provides support and services for products, including video tutorials, upgrade tools, and digital manuals.

URL: www.bigbigwon.com/support

BIGBIG WON SUPPORT