BIGBIG WON BLITZ Game Controller

01. Parts Diagram

The BIGBIG WON BLITZ controller features the following components:

• Top: HOME button, L button, LS button, D-pad (Directional Pad), Left light strip, Channel light, Trigger, Assignment buttons.
• Front: R button, + button, A/B/X/Y buttons, Right control stick, Right light strip, Configure button, Macro record button.
• Back: M4 button, ZR button, M2 button, M1 button, M3 button, ZL button.
• Bottom: Type-C port.

Package Contents:

Supported Platforms: Android/iOS / win10/11 / Switch

02. Power On/Off

Press and hold the [HOME button] for 3 seconds to turn the controller on or off.

03. Connection

The controller supports two connection methods: Bluetooth and Wired (Type-C).

• Bluetooth Connection: Long press the pairing button on top for 3 seconds after powering on. The [HOME button] light will flash rapidly, indicating pairing mode. The [HOME button] light will remain solid once connected successfully. The channel light indicates the connected Switch console.
• Wired Connection: After powering on the controller, use the Type-C cable to connect to the host device.

Note: The controller supports both Switch and Xinput modes. You need to switch to the corresponding host mode after connecting for normal use. Switch mode is the default.

• Steam: For Steam, enable 'Xbox Configuration Support' in Steam's Settings > Controller > General Controller Settings. Otherwise, issues may occur if the game does not recognize the controller.
• Switch: For Switch, after connecting via wired mode, navigate to System Settings > Controller and Sensors > Pro Controller Wired Communication.

04. Mode Switching

The controller supports both Switch and Xinput modes. You need to switch to the corresponding mode after connecting for normal use.

• Switch Mode: Press and hold the [A button] + [HOME button] for 3 seconds until the [HOME button] light turns red.
• Xinput Mode: Press and hold the [B button] + [HOME button] for 3 seconds until the [HOME button] light turns green.

Note: To connect iOS and Android devices via Bluetooth, switch to Xinput mode.

05. Assignments

The controller features four assignable buttons ([M1 button]/[M2 button]/[M3 button]/[M4 button]) that support button mapping.

• Setting Assignments: Press [FN button] + [M1 button]/[M2 button]/[M3 button]/[M4 button]. The [FN button] indicator will breathe, signifying entry into assignment mode. Press the button you wish to assign. The [FN button] indicator will flash twice to confirm the assignment.
• Clearing Single Assignment: Double-click the [FN button]. The [FN button] indicator will flash twice, indicating the current button's assignment has been cleared.
• Clearing All Assignments: Double-click the [FN button] directly. The [FN button] indicator will flash twice, indicating all button assignments have been cleared.

06. Turbo

This controller supports turbo functionality for 16 buttons, including [A button]/[B button]/[X button]/[Y button], directional buttons (↑/↓/←/→), [L button]/[R button], [ZL button]/[ZR button], and [M1 button] through [M4 button].

• Setting Turbo: Press and hold [FN button] + the desired button. The [FN button] indicator will flash twice to confirm. The [FN button] indicator will blink during active turbo.
• Clearing Single Turbo: Press and hold the button, then double-click the [FN button]. The [FN button] indicator will flash twice to confirm clearing.
• Clearing All Turbo: Double-click the [FN button] directly. The [FN button] indicator will flash twice to confirm clearing all turbo settings.
• Turbo Frequency: Press and hold [FN button] + the [+] button to cycle through frequencies: 5/s, 10/s, 20/s. The default is 5/s.

07. Macro Recording

This controller supports macro recording functionality. Each macro sequence can be assigned to a rear button ([M1 button]/[M2 button]/[M3 button]/[M4 button]).

• Recording Macro: Press and hold [FN button] + [M1 button]/[M2 button]/[M3 button]/[M4 button] for 3 seconds. The [FN button] indicator will breathe, indicating macro recording mode. Press the controller buttons to record the sequence. Click the [FN button] to stop recording. The [FN button] indicator will flash twice to complete recording. The [FN button] indicator will blink slowly during macro playback.
• Clearing Single Macro: Press and hold the [M button] assigned to the macro, then double-click the [FN button]. The [FN button] indicator will flash twice to confirm clearing.
• Clearing All Macros: Double-click the [FN button] directly. The [FN button] indicator will flash twice to confirm clearing all macro settings.

08. On-board Configuration Switching

This feature allows switching between different controller profiles stored on the device.

• Switch Mode: Click the [FN button]. The channel indicator will change from red to white, entering configuration switching mode. The four indicators represent four different on-board configurations. Click the [FN button] again to cycle through configurations; the indicators will count down. The mode will automatically exit after 5 seconds of inactivity, and the indicator will return to red.
• Xinput Mode: In Xinput mode, the channel indicator is always white, signifying the current on-board configuration. Configurations can be switched directly by clicking the [FN button].

09. Control Stick Dead Zone Switching

The controller is designed for competitive play with a factory default dead zone of 0 for optimal control. For users who prefer a dead zone, two options (0 and 10) are available.

Switching Dead Zone: Press and hold [FN button] + [LS button]/[RS button] downwards to toggle between the 0 and 10 dead zone settings for the left and right control sticks, respectively.

10. Control Stick Calibration

If the control stick drifts or does not reach its maximum value, calibration may be necessary.

• Enter Calibration: Simultaneously press the [+] button and the [-] button for 3 seconds. The left and right light strips will turn orange, indicating calibration mode.
• Calibrate: Push the control sticks to their maximum extents and rotate them in a full circle, repeating 3-5 times.
• Exit Calibration: Simultaneously press the [+] button and the [-] button again. The left and right light strips will flash twice and then turn off, indicating calibration is complete.

11. Gyroscope Calibration

If the controller's gyroscope is drifting, calibration can be performed as follows:

• Enter Calibration: Place the controller on a horizontal surface. Press and hold the [+] button and the [Screenshot button] simultaneously. The left and right light strips will breathe purple, indicating calibration mode.
• Complete: Wait a moment. When the left and right light strips flash purple, calibration is complete.

12. Vibration Adjustment

This controller supports four levels of vibration adjustment.

Adjust Vibration: Press [FN button] + the [+] button to cycle through vibration levels: Strong, Medium, Weak, and Off.

13. Battery Instructions

• Low Battery: When the battery is low, the light strips on the sides of the controller will flash red 10 times per second. This alert repeats every five minutes.
• Charging: When connected to a power source, the controller's light strips will breathe red, indicating charging. The charging light effect will turn off, and the light strips will return to their normal state when the battery is fully charged.
• Charging Dock: The charging dock has no indicator light in standby mode. When the controller is docked, if the dock's RGB indicator is cycling through seven colors, the controller is charging. If the dock's RGB indicator is solid green, the controller is fully charged.

14. Detailed Functional Instructions

For detailed video tutorials and support, please visit the official BIGBIG WON website's support page.

URL: https://www.bigbigwon.com/support

15. Your Rights

This product comes with a limited 12-month warranty from the date of purchase.