XBA-MOP4 Option Switch Settings

Supported bills: BDC 10, 20, 50, 100; BNU 10, 20, 50, 100 (4 bills).

XBA-MOP4 Option Switch Settings

FUNCTION	SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8
Reject MOP 10	ON
Accept MOP 10		OFF
Reject MOP 20			ON
Accept MOP 20				OFF
Reject MOP 50					ON
Accept MOP 50						OFF
Reject MOP 100							ON
Accept MOP 100								OFF
Reserved								ON
Reserved							OFF
Disable Bill Reject 4 Times								ON
BA Stop By 30 Sec							OFF
Enable Bill Reject 4 Times								ON
BA Stop By 30 Sec							OFF
Stack Banknote when Power-up								ON
Reject Banknote when Power-up								OFF
Reserved								ON
Reserved							OFF

Note 3: When Dip 1 is OFF, ICT106U MOP 10 = 0x40, MOP 20 = 0x41, MOP 50 = 0x42, MOP 100 = 0x43. When Dip 1 is ON, ICT106U MOP 20 = 0x40, MOP 50 = 0x41, MOP 100 = 0x42.

This dip switch is located at the side of XBA. The diagram shows a side view of the bill acceptor unit, indicating a DIP Switch labeled (2) and an LED indicator.

Currency Assign Data

Interface	ICT106U		ccNet	ICT104V	Pulse	MDB
Bill value	When Dip 1 is OFF	When Dip 1 is ON
BV1	10=0x40	20=0x40	10	10	10	10
BV2	20=0x41	50=0x41	20	20	20	20
BV3	50=0x42	100=0x42	50	50	50	50
BV4	100=0x43		100	100	100	100

Appendix

XBA-MOP4 (Pulse/MDB/ICT/ccNet)

FUNCTION	SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8
Inhibit Active HIGH	ON
Inhibit Active LOW		OFF
Reserved					ON
Reserved						OFF
Reserved							ON
Reserved								OFF
Pulse Mode (Credit-Pulse Normal HIGH)								ON
Pulse Mode (Credit-Pulse Normal LOW)								OFF
Other Mode								ON
Pulse Mode	MDB Mode		ccNet Mode		ICT104V Mode
1 pulse / MOP 10	OFF	OFF	OFF	ON
5 pulses / MOP 10	OFF	ON	ON	OFF
10 pulses / MOP 10	ON	ON	ON	ON
20 pulses / MOP 10	ON	OFF	ON	OFF

This dip switch is located on the CPU board. To access it, remove the CPU board cover first. The diagram illustrates the process: first, an image of the bill acceptor with an arrow indicating cover removal, followed by an image of the CPU board with the DIP Switch labeled (1) highlighted.

Manufacture setting: After setting the dip switch for credit pulses, reset the bill acceptor. Note: 1. No sleep function is available. 2. A calibration card is needed.

	XBA-UAH10 Bill Acceptor Option Switch Settings and Configuration Detailed guide for configuring the XBA-UAH10 bill acceptor, including option switch settings for Pulse, MDB, ICT106U, ccNet, and ICT104V modes, along with currency assignment data.
	XBA-TRY6 Bill Acceptor: Switch Settings and Protocol Configuration International Currency Technologies Corporation's XBA-TRY6 bill acceptor guide details switch settings for Pulse, MDB, ccNet, ICT104V modes. Learn currency assignment for Lira denominations and device configuration.
	XBA-MDL9 Bill Acceptor Switch Settings and Configuration Guide This document provides detailed option switch settings and currency assignment data for the XBA-MDL9 bill acceptor, covering Pulse, MDB, ICT106U, ccNet, and ICT104V modes. It includes configuration parameters for bill validation, operational functions, and currency denomination mapping.
	XBA-USD6 Option Switch Settings and Currency Configuration Guide Detailed guide to XBA-USD6 option switch settings, including pulse, MDB, ICT002U, ICT104U, and ICT104V modes, along with currency assignment data for various bill denominations.
	XBA-TWD4 Bill Acceptor Option Switch Settings and Configuration Guide Comprehensive guide detailing the XBA-TWD4 bill acceptor's DIP switch settings for various operating modes including Pulse, MDB, ICT104U, and ICT104V. Includes currency assignment data and configuration notes.
	XBA-NZD5 Bill Acceptor: Option Switch Settings and Currency Assignment Guide Comprehensive guide detailing the XBA-NZD5 bill acceptor's option switch configurations for various modes including Pulse, MDB, and ICT104V. Features currency assignment data for New Zealand Dollars (NZD) and switch location information.
	XBA-RUB6 Bill Acceptor: Option Switch Settings and Configuration Guide to XBA-RUB6 bill acceptor option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, including currency assignment data by International Currency Technologies Corporation.
	XBA-JMD6 Bill Acceptor Option Switch Settings and Configuration Guide Detailed guide to configuring the XBA-JMD6 bill acceptor, including option switch settings for various currencies (JMD) and communication protocols (Pulse, MDB, ICT). Covers currency assignment, setup notes, and DIP switch locations.

XBA-MOP4 Option Switch Settings