Baby Trend HC81945 High Chair

Parts List

• Seat Back x 1
• Height Bracket x 2
• Tray Insert x 1
• Tray x 1
• Upper Frame Assembly x 2
• Seat Back Hinge Rod x 1
• Seat Base x 1
• Crotch Retainer x 1
• Screw (3.5 mm x 10) x 4
• Front Leg x 1
• Rear Leg x 1
• Footrest x 1
• Caster (with brake) x 2
• Front Wheel x 2
• Seat Pad x 1
• Basket x 1

The first page displays the product name, model number, a list of all required parts for assembly, customer service contact information (1-800-328-7363), and the Baby Trend logo and website.

Safety Warnings

Important Safety Information:

⚠️ WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.

⚠️ WARNING: Prevent serious injury or death from falls or sliding out. Always secure child in the restraint. NEVER leave child unattended.

⚠️ WARNING: The child should be secured in the high chair at all times by the 5-point restraining system, either in the reclining, semi-reclining or upright position. The tray is not designed to hold the child in the chair. It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. See page 19 for instructions on proper use of restraint system.

⚠️ WARNING: Other accessory items may change the balance of the high chair and cause hazardous unstable conditions; use approved Baby Trend toys.

⚠️ WARNING: Be certain the high chair is fully erect and latched in the open position before allowing the child near the high chair.

⚠️ WARNING: Use of the high chair with a child weighing more than 40 pounds (18.14 kg) will cause excessive wear and stress on high chair.

⚠️ WARNING: The maximum weight that can be carried in the basket is 5 pounds (2.26 kg). Excessive weight may cause a hazardous unstable condition to exist.

⚠️ WARNING: NEVER allow your high chair to be used as a toy.

⚠️ WARNING: NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts.

Customer Service Contact: If you experience any difficulty with the use of our product or have a question regarding these instructions, please contact our Customer Service Department at 1-800-328-7363 between the hours of 8:00 a.m. and 4:30 p.m. (PST). Please do not return the product to the store as once it is returned it cannot be re-sold and the materials and energy used to make it are wasted.

Assembly Instructions

General Assembly Notes:

• To ensure safe operation, follow all instructions carefully and keep them for future reference.
• Before assembly and each use, inspect the product for damaged hardware, loose joints, missing parts, or sharp edges. NEVER use if any parts are missing or broken.
• Adult assembly is required.
• Always check that the high chair is locked in the open position before using.
• Carefully remove all parts from the box and verify you have all the parts for this model before assembling.

Parts Identification Diagram (Page 3): This diagram shows all parts labeled with numbers: 1. Seat Back, 2. Height Brackets, 3. Tray Insert, 4. Tray, 5. Upper Frame Assemblies, 6. Seat Back Hinge Rod, 7. Seat Base, 8. Crotch Retainer, 9. Front Leg, 10. Rear Leg, 11. Screws (3.5mm x 10), 12. Footrest, 13. Casters (with brake), 14. Front Wheels, 15. Seat Pad, 16. Seat Insert (optional), 17. Basket (optional).

1. Step 1: Prepare the Seat Base

   Place the Seat Base on a flat surface as shown in Figure 1. (Diagram shows the Seat Base on a flat surface.)

2. Step 2: Attach Seat Back to Seat Base

   Join the Seat Back to the Seat Base using the Seat Back Hinge Rod as shown in Figure 2. To install the hinge rod, press down on the hinge rod retainer and insert the rod into the hinge from right to left. (Diagram illustrates the Seat Back being joined to the Seat Base using the Seat Back Hinge Rod.)

3. Step 3: Attach Height Brackets

   Slide the left and right sides Height Bracket onto the Seat Base (Figure 3a). Snap the brackets into place (Figure 3b). (Diagrams show Height Brackets being slid onto the Seat Base and snapped into place.)

4. Step 4: Attach Footrest

   Slide the Footrest onto the Seat Base as shown in Figure 4. Snap the Footrest into place. (Diagram shows the Footrest being slid onto the Seat Base.)

5. Step 5: Attach Front Upper Frame Assembly

   Insert the front tube of the right side Upper Frame Assembly into the Height Bracket (Figure 5). The front tube is distinguished from the rear tube by the array of holes on its backside. (Diagram shows the front tube of the Upper Frame Assembly being inserted into the Height Bracket.)

6. Step 6: Secure Front Upper Frame Assembly

   Squeeze the Red Release Handle and push the tube through the Height Bracket until it locks in the highest position (Figure 6). (Diagram shows the Red Release Handle being squeezed and the tube pushed through the Height Bracket.)

7. Step 7: Attach Left Upper Frame Assembly

   Repeat Steps 5 and 6 for the left side Upper Frame Assembly (Figure 7). (Diagram indicates to repeat steps for the left side Upper Frame Assembly.)

8. Step 8: Attach Front Legs

   Insert the front legs into the ends of the front tube of both the right and left Upper Frame Assemblies (Figure 8). Ensure push buttons align with holes for proper connection. (Diagram shows front legs being inserted into the front tube of the Upper Frame Assemblies, highlighting push buttons and holes.)

9. Step 9: Attach Rear Legs

   Insert the rear legs into the ends of the rear tube of both the right and left Upper Frame Assemblies (Figure 9). (Diagram shows rear legs being inserted into the rear tube of the Upper Frame Assemblies.)

10. Step 10: Attach Wheels

    Attach each of the casters and front wheels to the high chair feet as shown in Figure 10. Ensure all wheels and casters are securely fastened. (Diagram illustrates the attachment of casters and front wheels to the high chair feet.)

11. Step 11: Attach Crotch Retainer

    Flip over the Tray to attach the Crotch Retainer. Orient the plastic housing so the slot faces the front of the Tray. Insert and tighten the 4 (3.5mm X 10) Screws. Do not overtighten. (Diagram shows the Tray being flipped over to attach the Crotch Retainer with screws.)

12. Step 12: Attach Seat Pad (Top)

    Loop the flap on the back of the Seat Pad over the top of the Seat Back. Connect the Seat Pad to the Seat Back using the two Elastic Loops, fitting them over the Attachment Tabs near the top harness slots (Figure 12). (Diagram shows the Seat Pad flap being looped over the Seat Back and connected with elastic loops to attachment tabs.)

13. Step 13: Attach Seat Pad (Bottom)

    Attach the bottom of the Seat Pad to the Seat Base using the two Elastic loops located at the rear of the Seat Pad. These fit over the Attachment Tabs on the Seat Base near where the Seat Back and Seat Base join (Figure 13). (Diagram shows the bottom of the Seat Pad being attached to the Seat Base with elastic loops.)

14. Step 14: Thread Harness Straps

    Thread the non-buckle end of the Harness Straps (Harness Attachment Tabs) through the provided slots in the Seat Fabric, Seat Insert, Seat Back, and Seat Base (Figure 14). Rotate the Harness Attachment Tabs 90 degrees once through the slots to ensure straps are firmly in place. (Diagram illustrates the Harness Attachment Tabs being threaded through slots in the seat fabric, insert, back, and base.)

15. Step 15: Remove Seat Back (for Infant Car Seat Attachment)

    To remove the Seat Back: With one hand, press down on the hinge rod retainer. With the other hand, slide the hinge rod to the right. Pull the rod out of the seat hinge and lift the seat back away (Figure 15). (Diagram shows how to remove the Seat Back by pressing the hinge rod retainer and sliding the rod.)

    Note: After removal, slide the rod back into the hinge on the seat for storage.

16. Step 16: Open High Chair

    Push the legs apart until fully open and locked (Figure 16). Push downward on the fold levers (left and right) to ensure the frame is locked open. (Diagram shows the legs being pushed apart to open and lock the high chair.)

17. Step 17: Attach and Operate Tray

    To attach the Tray, align the grooves on the bottom of the tray with the armrests of the high chair. Squeeze the Tray's release handle and slide the tray onto the armrests (Figure 17a). The Tray has a 3-position adjustment. To adjust, squeeze the Tray's release handle located underneath the tray and reposition to the desired position (Figure 17b). Release the handle and check that the Tray is securely locked. (Diagrams show the Tray being attached to the armrests and how to adjust its 3-position setting.)

    To Attach Insert Tray: The dishwasher-safe food Tray Insert snaps onto the High Chair Tray and is held by tabs on the sides. Ensure it snaps into place. To remove, unsnap tabs.

18. Step 18: Recline Seat

    Squeeze the recline lever on the back of the seat and adjust to the preferred recline or upright position (Figure 18). Be careful not to catch the child's arms, hands, or legs. (Diagram shows the recline lever on the back of the seat being squeezed to adjust the recline position.)

19. Step 19: Use Safety Belt

    Place your child's arms through the loops formed by the shoulder and waist straps. Place the crotch strap between your child's legs. Insert the Harness Buckles into the Center Clasp with the Red Button. Adjust shoulder and waist straps for comfort and safety by sliding buckles. Ensure straps fit snugly. (Diagram illustrates how to place the child's arms and straps into the buckles and adjust for a snug fit.)

20. Step 20: Release Safety Belt

    Push the Red Button on the Center Clasp to release the two Harness Buckles (Figure 20). (Diagram shows the Red Button on the Center Clasp being pushed to release the harness buckles.)

21. Step 21: Adjust Seat Height

    Squeeze both left and right levers of the Height Adjustment Bracket and adjust to the ideal position (Figure 21). Ensure the bracket is level and both sides are locked before placing the child. (Diagram shows the levers for adjusting the seat height.)

22. Step 22: Fold High Chair

    Place Seat Back in the most upright position (Figure 22). (Diagram shows the Seat Back being placed in the most upright position for folding.)

23. Step 23: Stow Tray for Folding

    Squeeze the tray release handle and slide the tray out (Figure 23a). Hang the tray on the hooks located on the back of the rear leg (Figure 23b). (Diagrams show the tray release handle being used to slide the tray out and hang it on the rear leg hooks.)

24. Step 24: Fold High Chair

    Pull upward on the release levers (located on the sides of the frame) and push the rear legs in the direction of the front legs until folded (Figure 24). The chair is now ready to put away. Do not allow children to play around a folded high chair as it may fall. (Diagram shows the release levers being pulled upward and rear legs pushed inward to fold the chair.)

25. Step 25: Unfold High Chair

    Push the legs apart until fully open and locked. Push downward on the fold levers (left and right) to ensure the frame is locked (Figure 25). (Diagram shows the legs being pushed apart to unfold and lock the chair.)

Maintenance and Care

⚠️ WARNING: Harness Straps and Basket are NOT washable.

Dishwasher Safe Tray Insert:

The Tray Insert is dishwasher safe up to 160 degrees Fahrenheit. Do not use scouring pads as they can damage the surface.

High Chair/Tray:

Clean the High Chair and Tray after each use with mild household dish soap. Use a soft bristle brush, sponge, or cloth. Do not submerge the high chair or tray in water. Surface clean only.

Seat Pad:

Refer to the care label on the seat pad for specific cleaning instructions.

To Remove Seat Pad:

Remove Harness Straps by pushing Harness Attachment Tabs through the harness slots on the Seat Back, Seat Base, and Seat Pad. Remove Elastic Loops from Attachment Tabs on Seat Base and Seat Back.

Non-Washable Seat Pad:

Use a sponge or cloth with mild household detergents for surface cleaning. DO NOT MACHINE WASH.

Washable Seat Pad:

Machine Wash COLD DELICATE CYCLE with non-chlorine based Laundry Detergent. DO NOT USE BLEACH. HANG DRY. DO NOT MACHINE DRY.

Basket:

Some models include a basket underneath the seat for storage. To remove: Release the four snaps. To attach: Feed snap strips around basket slots underneath the Seat Base and press firmly on the snaps.