Foxeer Monster 1200TVL Widescreen Camera
Instruction Manual
[Foxeer Logo]
MONSTER 1200TVL Widescreen Camera
Instruction Manual
WARNING
Read the ENTIRE instruction manual to become familiar with the features of this product before operating. Failure to operate the product correctly can result in damage to the product, personal injury and cause serious injury.
[Warning Symbol] Age Recommendation: Not for children under 14 years. This is not a toy.
NOTICE: This product is intended for use with an unmanned aerial vehicle (drone) and aircraft. Foxeer disclaims all liability for the intended purpose and its misuse. For warranty service, refer to there.
SUPPORT: Visit www.foxeer.com/support to get more information.
Camera-OSD Switch Connection
Diagram showing the OSD switch connection. It shows wires for GND, 5V, Video, OSD Signal, Voltage Sensor, and 1200TVL Wide Screen. The OSD Switch itself is depicted with pins labeled for these connections.
Camera-Video Transmitter Connection
To connect the camera directly to the video transmitter, plug the 4-pin wiring harness from the video transmitter into the camera, leaving the OSD pin open.
OSD Menu Navigation
MENU: Button (center button) to go to the main menu.
UP/DOWN: Move up and down through the menu.
LEFT/RIGHT: Modify the menu parameters.
FPV OSD Setup
- Long press left button, user name info will flicker, you can move user name to any position, then press 'NEXT', click 'SAVE', user name is done.
- Long press top button, you can setup user name, besides, OSD info to create or disable.
- Press 'MENU', 'SAVE', 'EXIT' to exit.
1. EXPOSURE
Move the cursor to 'EXPOSURE', press the LEFT/RIGHT button to select 'STD' or 'EXPO' mode.
| EXPOSURE | STD |
| SHUTTER MODE | AUTO |
| AGC | MIDDLE |
| AWB | ATW1 |
| IMAGE ADJ | [Leads to Image Adjustment Menu] |
[PREV] [NEXT] [SAVE] [EXIT]
2. SHUTTER MODE
Move the cursor to 'SHUTTER MODE', press the LEFT/RIGHT to select 'AUTO' or 'MANUAL'. Camera normally works on 'AUTO MODE'.
| SHUTTER SPEED | 1/25 to 1/10000 |
[RETURN]
3. AGC
'AGC' can adjust the peak value, the bigger value, the brighter image cause bigger noise. There are 'ON' or 'OFF' options by LEFT/RIGHT according to actual record.
| AGC | ON |
| INTENSITY | MIDDLE |
[RETURN]
5. IMAGE ADJ
When the IMAGE is displayed on screen, it allows you to do settings of image function and details.
SHARPNESS: used to adjust overall image sharpness, can set from 0-100, the higher value, the sharper image.
HDNR: used to adjust overall image noise, which can set from 0-100.
CONTRAST: the area ratio of the brightest screen and darkest areas, it can set from 0-100.
SATURATION: used to adjust bright degree of color. It can set from 0-100, the higher value, the deeper image color.
R GAIN: can adjust the value to change color.
PRESS 'NEXT' to enter next page.
| IMAGE ADJ | SHARPNESS | 50/100 |
| HDNR | 80/100 | |
| CONTRAST | 50/100 | |
| SATURATION | 50/100 | |
| R GAIN | 44/100 |
[NEXT] [RETURN]
This page have two options, 'G GAIN', 'B GAIN'.
| IMAGE ADJ | G GAIN | 40/100 |
| B GAIN | 42/100 |
The user can adjust the value to change color, also can set different color value according to camera environment.
[NEXT] [RETURN]
6. DAYNIGHT
Return to main page, press 'NEXT' button to enter next page.
'DAYNIGHT' has four modes, 'EXT', 'COLOR', 'BW', 'AUTO GEN'. It is synchronous with infrared lamp's opening and closing time.
'EXT' mode can choose from 0/100 to 100/100. In 'COLOR' mode, image will always be color. In 'BW' mode, image will always be black and white. 'AUTO GEN' can control the camera output color or black and white image according to the strength of the light, can set daynight delay as picture below.
| DAYNIGHT | EXT |
| D TIME | 0/100 |
| D CTPL | 0/100 |
| NIGHT2DAY | 80/100 |
| DAY2NIGHT | 70/100 |
[PREV] [NEXT] [SAVE] [EXIT]
7. SYSTEM
'SYSTEM' contains 5 parameters.
'TV GAMMA' is used to adjust contrast, it is fixed.
'TV BRIGHT' is used to adjust image bright.
'TV SYSTEM' comes with 'PAL' or 'NTSC' two modes for user of different nationalities.
'LANG' comes with 'Chinese', 'Japanese', 'English' three languages for user of different nationalities. User can select the language by LEFT/RIGHT.
'RELOAD FTY' has option 'NO'.
| SYSTEM | TV GAMMA | [Value Not Specified] |
| TV BRIGHT | [Value Not Specified] | |
| TV SYSTEM | PAL | |
| LANG | ENG | |
| RELOAD FTY | NO |
[PREV] [NEXT] [SAVE] [EXIT]
8. BAD PIXEL
'BAD PIXEL' is for bad pixel repair. USER can choose 'ON' or 'OFF' mode.
| BAD PIXEL | MODE | ON |
| INTENSITY | MIDDLE |
[RETURN]
9. PRIVACY MASK
User can adjust the size, position, color, transparency of the chosen area.
| PRIVACY MASK | MODE | OFF |
| DEF COLOR | 1/15 | |
| SWITCH | OFF | |
| RANGE | MIDDLE |
[SELECT] [RETURN]
10. HLC
In 'HLC' menu, press LEFT/RIGHT key to select 'ON' or 'OFF'.
| HLC | MODE | OFF |
| BLACKNESS | 0/100 |
[RETURN]
11. WDR
press 'NEXT' button to enter next page.
In 'WDR' menu, press LEFT/RIGHT key to select 'LOW' 'MIDDLE' 'HIGH'.
| WDR | LOW |
[RETURN]
12. SAVE
When the user finish setting and want to save it, please choose 'SAVE' and press 'EXIT' to exit the OSD menu, the setting will be saved in FLASH and will not loose when the power supply is off or the system is restarted.
13. EXIT
Press 'EXIT' to exit the OSD menu.
| DAYNIGHT | EXT |
| BAD PIXEL | ON |
| PRIVACY MASK | OFF |
| HLC | OFF |
[PREV] [NEXT] [SAVE] [EXIT]
