VEVOR METAL CHICKEN COOP USER MANUAL

Introduction

VEVOR is committed to providing tools at competitive prices. The terms "Save Half" or "Half Price" represent an estimate of savings compared to major brands and may not apply to all product categories. Please verify savings carefully when ordering.

Product Overview

This manual provides instructions for the VEVOR Metal Chicken Coop, Model YD322. Please read all instructions carefully before operating the product. VEVOR reserves the right to interpret the user manual. The appearance of the product is subject to the item received. Updates to technology or software may occur without prior notice.

NEED HELP? CONTACT US!

For product questions or technical support, please contact:

Technical Support and E-Warranty Certificate
www.vevor.com/support

SAFETY INSTRUCTIONS

WARNING: Read this material before using this product. Failure to do so can result in serious injury.

Assembly precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or under the influence of alcohol, drugs, or medication.
6. Product capabilities apply only to properly and completely assembled products.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the metal chicken coop.
8. For additional information regarding parts, refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use precautions

1. DO NOT SIT OR STAND ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or near this item.
3. Do not exceed specified weight capacities.
4. Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded metal chicken coop.
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

TOOLS

The following tools are recommended for assembly: Gloves ?, Safety Goggles ?, Power Drill ड्रिल, Screwdriver ?.

PARTS LIST

A comprehensive list of parts with quantities is provided in the manual. Key components include various tubes (Parts 1, 2, 3Y, 4Y, D1, D2, D3, D4Y, D5Y, D6Y, D7Y), connectors (Parts AY, AY-1, AY-2, C), base supports (Parts 5, 6), a roof panel (Part J), netting (Part F), and fasteners (Parts H, K, L, M, N, P, D8).

Note on Button Clips: Tubes and joints are connected using pre-inserted button clips. Press the clip to insert the tube. Forcing may damage the clip. Pay attention to the orientation of Part P.

Note on Part 3Y and C connection: Ensure the button clip on Part C points left and right when connecting Part 3Y.

Note on Screw L: A power tool is needed to drive screw L into tube D7Y.

Note on Parts D3 and D6Y: Exact placement is not critical, but ensure D6Y is covered by two pairs of H. Screw L is not used in detailed illustrations for adjustment flexibility. Use screw L to secure H once satisfied with the placement.

ASSEMBLY STEPS

The assembly is divided into several steps, visually guided by diagrams:

Step 1: Base Frame Assembly

Connect parts 1, 2, 5, 6, C, and D to form the base structure of the coop. Part P is used to secure these connections.

Step 2: Vertical Supports

Attach vertical tubes (Part 3Y) to the base frame using the button clips on Part C. Ensure correct orientation of the clips.

Step 3: Upper Frame (Sides)

Install horizontal and angled tubes (Parts AY, AY-2) to create the side structure.

Step 4: Upper Frame (Roof Arches)

Attach the roof arch tubes (Parts AY-1, 4Y) to complete the main frame structure.

Step 5: Roof Supports

Install roof support tubes (Parts D1, D2, D5Y, D4Y, D7Y) along the arched frame. Use screw L with a power tool for D7Y.

Step 6: Roof Supports (Center)

Install center roof support tubes (Parts D3, D6Y) and secure them with fasteners (H, K, L).

Step 7: Rear Support

Attach the rear support bracket (D8) and secure with fastener K.

Step 8: Netting Installation

Unroll the poultry net (F) and attach it to the frame. Do not precut the net. Roll it along the tubes and cut as needed. Use zip-ties to fasten. Follow the arrows in the diagrams for the correct direction of net placement. Overlaps between nets are expected.

Note on Netting: For the back of the coop, roll the net without measuring. For the front, it may be easier to measure and cut the net. The front rectangular area is wider than the net roll, so vertical rolling might not cover it completely. Follow the arrows for rolling and cutting.

PRODUCT PARAMETER

Manufacturer and Importers

Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX