VEVOR Metal Chicken Coop User Manual

Introduction

VEVOR is committed to providing tools at competitive prices. The terms "Save Half" or "Half Price" represent an estimate of savings compared to major brands and may not apply to all product categories. Please verify savings carefully when placing an order.

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret this user manual. The product appearance is subject to the actual item received. VEVOR may update technology or software without prior notice.

Safety Instructions

WARNING: Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or under the influence of alcohol, drugs, or medication.
6. Product capabilities apply to properly and completely assembled products only.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the metal chicken coop.
8. For information regarding parts, refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use Precautions

1. DO NOT SIT OR STAND ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or near this item.
3. Do not exceed specified weight capacities.
4. Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded metal chicken coop.
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Tools Required

The following tools are depicted: Gloves ?, Safety Goggles ?, Power Drill ड्रिल, Screwdriver ?.

Parts List

The following parts are included:

Assembly Steps

Step 1

Assemble the base frame. Connect parts 1, 2, 5, 6, C, D, and P as shown in the diagram. Ensure the button clips are properly engaged. Note: Button clips are pre-inserted in tubes. Press the clip to insert the tube into the joint. Avoid forcing to prevent damage.

Diagram shows the base frame being assembled with parts labeled FRONT, LEFT, BACK, RIGHT. Specific parts and their connections are indicated.

Step 2

Attach vertical support tubes (Part 3) to the base frame. Connect Part 3 to Part C, ensuring the button clip on Part C points left and right as illustrated.

Diagram shows the base frame with vertical tubes (Part 3) being attached. A close-up shows the correct orientation of the button clip on Part C.

Step 3

Add horizontal frame tubes (Parts A and B) to create the main structure. Connect parts A and B to the vertical supports.

Diagram shows the addition of horizontal tubes (A and B) to the structure, forming the sides and top of the coop.

Step 4

Continue assembling the roof structure with parts 2, 4, A, and B. Connect the roof support tubes to the main frame.

Diagram shows the roof structure being assembled, with parts 4 forming the pitched roof.

Step 5

Install the roof connectors (D1, D2, D4, D5, D7) and frame tubes (D1, D2, D5, D7). Secure connections using screws (H), bolts (K), and nuts (L). A power tool is recommended for driving screw L into tube D7.

Diagram shows the installation of roof connectors and tubes. Close-ups illustrate the use of screws, bolts, and nuts for secure connections. A note indicates the need for a power tool for screw L.

Step 6

Attach the remaining connectors (D3, D6) and secure them with screws (L). Ensure D6 is covered by the pairs of H. Screw L is not used in the detailed illustrations to allow for adjustment of D3 and D6. Once satisfied with the positioning, use screw L to secure H.

Diagram shows the attachment of D3 and D6 connectors. Close-ups illustrate the adjustment and securing process using screws and bolts. A note clarifies the purpose of not using screw L initially.

Product Parameter

Manufacturer and Importers

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED, C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX