VEVOR Over Toilet Storage Cabinet KLBC-03
Affordable. Reliable. Home Improvement.
Product Overview
This document provides instructions for assembling the VEVOR Over Toilet Storage Cabinet, Model KLBC-03.
Important: Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product is subject to the received item. Updates to technology or software will not be individually notified.
Safety Warning Instructions for Installation
To reduce the risk of injury, users must read the instructions carefully.
- Install and use the product according to the steps and recommendations in this manual.
- The seller is not liable for injuries or damages caused by improper installation or use.
- Children are not allowed to assemble this product. Keep small parts out of children's reach to prevent swallowing, inhaling, and related injuries.
- Keep plastic packaging away from children to avoid suffocation risk during play.
- Wear gloves during assembly/disassembly to avoid cut-related injuries.
- Assemble the product on a spacious surface and do not place unpackaged products directly on the floor to avoid damage.
- Avoid long-term moisture to prevent mold growth and deformation.
- Keep the product away from sharp objects and corrosive substances.
- Regularly check the secure fit of screws during use and tighten loose screws to ensure structural integrity.
- Consider using fastening elements to secure the furniture to the wall or other objects to prevent tipping, depending on the environment.
- Place the product on a flat and stable surface during use.
Product Parameters
| Model | Product Specifications (mm) | Width and Height of the Legs (mm) |
|---|---|---|
| KLBC-03 | 1680 × 785 × 195mm | 900 × 590 |
Accessories List
The following parts and hardware are included:
- Part 1: Top Panel (long)
- Part 2: Left Tall Side Panel
- Part 3: Top Panel (short)
- Part 4: Right Tall Side Panel
- Part 5: Top Shelf
- Part 6: Middle Tall Side Panel
- Part 7: Middle Divider/Support
- Part 8: Adjustable Shelf
- Part 9: Upper Back Support Panel
- Part 10: Upper Back Panel
- Part 11: Middle Back Panel/Divider
- Part 12: Left Lower Side Panel
- Part 13: Right Lower Side Panel
- Part 14: Lower Back Panel
- Part 15: Lower Support Panel
- Part 16: Lower Support Panel
- Part 17: Hinge Plate
- Part 18: Left Door
- Part 19: Right Door
- Part 20: Upper Back Panel (alternative)
- Part 21: Upper Back Panel/Mounting Bracket (alternative)
- Part 22: Lower Shelf
- Part 23: Drawer Front
- Part 24: Drawer Box/Panel
- Hardware A: Cam Lock (x10+2)
- Hardware B: Cam Bolt (x10+2)
- Hardware C: Wooden Dowel (x3+1)
- Hardware D: Screw (x3)
- Hardware E: Shelf Pin (x4+1)
- Hardware F: Screw (x44+2)
- Hardware G: Screw (x10+2)
- Hardware H: Screw (x10+2)
- Hardware I: Handle Screw (x3)
- Hardware J: Handle (x6)
- Hardware K: Hinge (x2)
- Hardware L: Wooden Dowel (x1)
- Hardware M: Wall Anchor Screw (x4)
- Hardware N: Screw Cap/Cover (x54)
Installation Steps
Step 1
Attach part 21 to part 4 using 3x hardware D and 2x hardware F. Attach part 7 to part 4 using hardware F.
Step 2
Attach part 9 to part 1 using 2x hardware F. Attach parts 7 and 4 to part 1 using 2x hardware A and 2x hardware B. Rotate hardware A to lock.
Step 3
Attach part 6 to parts 4 and 7 using 2x hardware F.
Step 4
Attach part 2 to the assembly of parts 1, 6, and 7 using 7x hardware F.
Step 5
[Insert] part 10 into the top of the structure formed by parts 1, 6, and 2.
Step 6
Attach part 3 to the top of parts 1 and 6 using 5x hardware F.
Step 7
Attach part 7 and part 2 to the main structure using 2x hardware A and 2x hardware B. Rotate hardware A to lock.
Step 8
[Insert] part 11 into the structure, fitting into the designated slots.
Step 9
Attach part 5 to the top of the structure formed by parts 3, 2, and 11 using 6x hardware F.
Step 10
Assemble the side units. Attach parts 21, 22, 23, and 24 to part 13 and part 12 using 14x hardware F and 2x hardware C.
Step 11
Connect the two main side assemblies (parts 12, 13, 14, 15, 16) using 8x hardware F. Two configurations are shown.
Step 12
Attach the back panel (part 20 or 21) to the side assemblies. Two configurations are shown.
Step 13
Connect the main cabinet structure to the side units using 6x hardware A, 6x hardware B, 3x hardware C, and 1x hardware L. Two configurations are shown.
Step 14
Secure the back panels (parts 10 and 11) to the main structure using 10x hardware G and 10x hardware H.
Step 15
Attach handles (part J) to doors (parts 18 and 19) using 6x hardware J, 2x hardware K, and 3x hardware I.
Step 16
Attach the doors (parts 18 and 19) to the main cabinet.
Step 17
Insert shelf 8 into the cabinet using 4x hardware E.
Step 18
[Secure] the unit to the wall using 4x hardware M.
Step 19
Attach screw caps/covers (N) to the unit using 54x hardware N.
Manufacturer and Importer Information
Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
EC REP: E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.
