VEVOR Shoe Cabinet User Manual
Model: HZS003
Technical Support and E-Warranty Certificate: www.vevor.com/support
Product Overview
This document provides instructions for the VEVOR HZS003 Shoe Cabinet. It includes safety precautions, a list of all parts, detailed assembly steps, and product specifications.
The VEVOR HZS003 is a 3-layer shoe cabinet designed for organizing footwear in entryways, hallways, or living rooms. It features flip drawers for easy access and storage.
Safety Instructions
WARNING:
Read these instructions carefully before using this product. Failure to do so can result in serious injury.
Assembly Precautions:
- Assemble only according to these instructions. Improper assembly can result in hazards.
- Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
- Keep the assembly area clean and well-lit.
- Keep bystanders out of the area during assembly.
- Do not assemble when tired or under the influence of alcohol, drugs, or medication.
- The product capabilities apply to properly and completely assembled products only.
- Assemble on a flat, level, hard, and smooth surface capable of safely supporting the shoe cabinet.
- For additional information regarding the parts listed, please refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.
Use Precautions:
- DO NOT SIT OR STAND ON THIS ITEM.
- This product is not a toy. Do not allow children to play with or near this item.
- Do not exceed weight capacities.
- Use only on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded shoe cabinet.
- Use as intended only.
- Inspect before every use; do not use if parts are loose or damaged.
SAVE THESE INSTRUCTIONS
Parts List
Ensure all parts are present before assembly. Refer to the identifiers below:
Assembly Steps
Step 1
Insert cam locks (I1, I2) into the pre-drilled holes on the side panels (2 and 3). Ensure the arrow on the cam lock points towards the entry hole for the screw.
[Diagram shows inserting cam locks I1 and I2 into panels 2 and 3, with arrows indicating orientation. Quantity: x6 for each type.]
Step 2
Attach the shelves (4) and base panel (5) to the left side panel (2). Insert screws (A) into the corresponding holes and secure them by turning the cam locks (I1) clockwise.
[Diagram shows panel 2 with shelves 4 and base panel 5 attached using screws A and cam locks I1. Quantity: x6 for cam locks.]
Step 3
Attach the right side panel (3) to the assembled structure. Insert screws (B) and secure them by turning the cam locks (G) clockwise. Note: The diagram shows cam locks G, but the parts list shows G as hammered nails. Assuming G refers to the cam lock mechanism in this step, or there's a typo. Let's assume cam locks are used here as per the visual logic.
[Diagram shows attaching panel 3 to the structure from Step 2, using screws B and cam locks G. Quantity: x4 for screws B.]
Step 4
Attach the top panel (1) to the side panels (2 and 3). Use screws (P) to secure the top panel.
[Diagram shows attaching top panel 1 to panels 2 and 3 using screws P. Quantity: x4.]
Step 5
Attach the drawer support structures (6) to the inside of the side panels (2 and 3). Use screws (E) and cam locks (H1, H2) to secure them.
[Diagram shows attaching drawer support structures 6 to panels 2 and 3 using screws E and cam locks H1, H2. Quantity: x3 sets of H1/H2, x18 screws E.]
Step 6
Attach the drawer mechanisms (7) to the drawer support structures (6). Use screws (E) to secure them.
[Diagram shows attaching drawer mechanisms 7 to the support structures 6 using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 7
Attach the drawer front panels (6) to the drawer mechanisms (7). Use screws (E) to secure them.
[Diagram shows attaching drawer front panels 6 to drawer mechanisms 7 using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 8
Attach the drawer side panels (8) to the drawer front panels (6). Use screws (E) to secure them.
[Diagram shows attaching drawer side panels 8 to drawer front panels 6 using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 9
Attach the drawer back panels (9) to the drawer side panels (8). Use screws (E) to secure them.
[Diagram shows attaching drawer back panels 9 to drawer side panels 8 using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 10
Insert the drawer bottoms (not explicitly numbered but implied to be part of the drawer assembly) into the assembled drawer frames.
[Diagram shows inserting drawer bottoms into the drawer structure.]
Step 11
Attach the drawer runners (7) to the inside of the main cabinet side panels (2 and 3). Use screws (E) to secure them.
[Diagram shows attaching drawer runners 7 to the inside of panels 2 and 3 using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 12
Attach the drawer front panels (6) to the drawer runners (7) using screws (C) and cam locks (D).
[Diagram shows attaching drawer front panels 6 to drawer runners 7 using screws C and cam locks D. Quantity: x6 screws C, x3 cam locks D.]
Step 13
Insert the assembled drawers into the cabinet, aligning them with the runners.
[Diagram shows inserting the assembled drawers into the cabinet.]
Step 14
Attach the drawer hinges (F) to the drawer front panels (6) and the cabinet side panels (2 and 3). Use fasteners (I3) to secure them.
[Diagram shows attaching hinges F to drawer fronts 6 and cabinet panels 2, 3 using fasteners I3. Quantity: x6 hinges F, x6 fasteners I3.]
Step 15
Insert the drawer fronts (6) into the cabinet, aligning them with the hinges.
[Diagram shows inserting drawer fronts 6 into the cabinet, aligning with hinges.]
Step 16
Secure the drawer fronts (6) to the cabinet using screws (E).
[Diagram shows securing drawer fronts 6 to the cabinet using screws E. Quantity: x3 sets, x6 screws E per set.]
Step 17
Attach the top panel (1) to the side panels (2 and 3) using brackets (K) and screws (L).
[Diagram shows attaching top panel 1 to side panels 2 and 3 using brackets K and screws L. Quantity: x2 sets.]
Step 18: Wall Mounting
For safety, it is recommended to secure the shoe cabinet to the wall. Mark the desired height on the wall. Drill holes at the marked positions using a drill. Insert wall anchors (N) into the drilled holes. Attach brackets (K) to the wall using screws (A) and anchors (N). Secure the cabinet to the brackets using screws (A).
[Diagram shows drilling holes, inserting anchors N, attaching brackets K to the wall with screws A, and then securing the cabinet.]
Step 19: Final Securing
Use cable ties (M) to secure the cabinet to the wall for added stability. Pass the cable ties through the designated holes on the cabinet and around a secure point on the wall or furniture. Tighten the cable ties. Alternatively, use fasteners (R, J, L) as shown in the diagram for securing.
[Diagram shows securing the cabinet to the wall using cable ties M, and also shows alternative securing methods with fasteners R, J, L.]
Product Parameters
| Parameter | Value |
|---|---|
| Package size (mm) | 1316×425×139 |
| Size (mm) | 600*237*1200 |
| N.W (kg) | 20.45 |
| G.W (kg) | 23.2 |
| Colour | White |
| Type | 3 layers |
| Texture | Chipboard |
| Base | No legs |
| Load-bearing | ≥100 lbs |
Company Information
Manufacturer Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREET EASTWOOD, NSW 2122 Australia
Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
UK Representative: Pooledas Group Ltd, Unit 5 Albert Edward House, The Pavilions, Preston, United Kingdom
EU Representative: SHUNSHUN GmbH, Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany
Origin: Made In China
For product questions or technical support, please contact: CustomerService@vevor.com
Contact Us â Official VEVOR Support
