MoesGo Smart Switch Instruction Manual

Introduction

This instruction manual provides detailed guidance for the MoesGo Smart Switch, designed with a glass panel and touch controls, offering versatile control options via Wi-Fi and RF433. It integrates with the Smart Life/Tuya App and supports multi-control association.

The manual is available in multiple languages, including German, Spanish, French, Russian, Italian, Portuguese, Polish, and Arabic. Please refer to this English version for detailed instructions.

Product Description

This new designed glass panel wireless touch smart switch is designed with WiFi+RF to replace traditional switches with a variety of ways to control. Now one new smart feature as multi-control association to other smart switches is added into the Smart Life/Tuya App, together with the backlight on/off and relay status. Its scratch resistance glass panel is suitable for different decoration styles with its best value.

Note: Button sound on and off: no button operations before operations begin within 6 seconds. Then press switch button for 4 times and long press for the fourth time until the switch beep sounds as Di-Di for 2 times for successful operation.

Safety Information

⚡Risk of Electric Shock: Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician.

Technical Parameters

Warnings

Turn off the power at the circuit breaker and test that power is off before wiring.

Installation

Note: Make sure that the power at the circuit breaker is off before wiring.

• A Neutral Wire is required. Confirm the wall box contains a Neutral Wire (typically white). If the wall box doesn't have a Neutral Wire, please try another location at your home or call a professional electrician to install the switch.
• The wire colors indicated in this manual are the usual colors and may differ in some houses.
• Ensure the wire conductors are securely fastened to each wire.
• Ensure the Wi-Fi signal is steady and normally working before wiring.
• If you don't have any wiring experience, please call a professional electrician.

Step 1: Turn off power

Turn off the circuit breaker and use the electrical tester to test the power. Ensure the circuit breaker is off before wiring.

Attention: Please disconnect the power supply before installing or removing the device for avoiding irreversible damage on the device from the electric current or some unpredictable problems such as lamp flashing.

Step 2: Remove the old switch

Remove the old switch faceplate.

Verify power is off: We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit. You may need to turn off more than one circuit breaker.

Step 3: Identify wires

Remove the switch and pull it away from the wall. Identify Line/Load Wire (Note: The color of your wire may be different from the color shown on the manual).

Step 4: Take pictures of the wiring

Take pictures of the existing wiring to help with reassembly.

Step 5: Remove the panel

Remove the panel with a screwdriver. ? (Please don't install with electricity power on).

Step 6: Prepare to install wiring

Connect wires according to the gang configuration:

• A. Live wire connects to "L" terminal.
• B. Neutral wire connects to "N" terminal.
• C. Lamp wire connects to "L1", "L2", "L3", "L4" terminals as applicable.

Gang Configurations:

• 1 Gang: Connects to "L1" terminal. (1 Gang L1 and N line)
• 2 Gang: Connects to "L1", "L2" terminals. (2 Gang L1 and N line)
• 3 Gang: Connects to "L1", "L2", "L3" terminals. (3 Gang L1 and N line)
• 4 Gang: Connects to "L1", "L2", "L3", "L4" terminals. (4 Gang L1 and N line)

Wiring Diagram Description:

The diagram shows the connections for 1-3 Gang and 4 Gang switches. Live (L) and Neutral (N) wires connect to the switch, and Lamp wires (L1, L2, L3, L4) connect to the respective output terminals for controlling lights.

Step 7: Install the switch

Put the switch into the switch box in the wall.

Mount the two side screws.

Install the glass panel (install from up above).

Finish installation.

Add Devices

This section guides you through adding the smart switch to your mobile app.

1. Download MOES App

MOES App is upgraded for better compatibility than Tuya Smart/Smart Life App, offering enhanced features for scene control, widgets, and recommendations. (Note: Tuya Smart/Smart Life App still works, but MOES App is highly recommended).

[QR Code for MOES App download]

2. Registration or Log in

Download the "MOES" Application.

Enter the Register/Login interface: tap "Register" to create an account by entering your phone number to get a verification code and set a password. Choose "Log in" if you already have a Smart Life account.

3. Configure the APP to the switch

Preparation: Ensure the switch has been connected with electricity, your phone is connected to Wi-Fi ?, and can access the Internet.

Note: The switch only supports 2.4G network. If you have connected to a 5G network, please disconnect the 5G network first and then connect to the 2.4G network.

Wi-Fi link method

Complete the wiring of the switch module before pairing.

Note: The switch only supports 2.4G network. If you have connected to a 5G network, please disconnect the 5G network first and then connect to the 2.4G network.

1. Scan the QR code to configure the network guide. [QR Code]
2. Select EZ mode, tick to confirm that the indicator flashes, and click Next.
3. Enter Wi-Fi Password and click "Next", waiting for completing the connection.
4. Select the device you want to add and click "+".
5. Add the device successfully, you can edit the name of the device to enter the device page by clicking "Done".
6. Click "Done" to enter the device page to enjoy your smart life with home automation.

How to reset/re-pair Wi-Fi code

Press the switch button for 6 times, and hold on the 6th time, then release until you hear "Di-Di-Di" (3 times). The blue indicator on the switch will flash fast after 3 seconds. Reset/re-pair is successful.

Remote radio frequency (RF) link method

Pair and clear up the RF code

1. How to pair the RF code

• 1.1 (Can be turned on and off): Confirm your switch is off before operations. Press the switch button for about 8 seconds until you hear "Di-Di" (2 times). Then the matching of RF code is successful. The key of the remote controller can control the switching of the state of the switch on and off corresponding to the position of the switch.
• 1.2 (Open only): Confirm your switch is off before operations. Press the switch button for about 5 seconds until you hear "Di" (1 time). After that, release the button, press the corresponding button on the remote control to turn on. Then the matching of RF codes is successful. The key of the remote controller can control the corresponding position of the switch to be open.
• 1.3 (Close only): Confirm your switch is on before operations. Press the switch button for about 5 seconds until you hear "Di" (1 time). After that, release the button, press the corresponding button on the remote control to turn on. Then the matching of RF codes is successful. The key of the remote controller can control the corresponding position of the switch to be closed.

2. How to clear up the RF code

Confirm your switch is off before operations. Press the switch button for a long time until you hear "Di-Di-Di-Di" (4 times), and then release the button. The RF code is now cleared up.

How to achieve multi-control association

Note: Please confirm you have successfully finished the WiFi link method above for adding this switch to your Smart Life App before the association.

1. WiFi add another smart switch to the same Smart Life/Tuya App. (If there is a smart switch already added to the app, just go to the next step.) Note: There is no need to wire the new added switch to the light; only L and N are required for wiring.
2. Then you will see two devices in the app. Click the main switch (as One gang switch shown below) to enter the next operation.

Diagram Description: The diagram shows a "Main Switch" and a "New Added Switch" or "Associated 1" / "Associated 2". This illustrates how multiple switches can be linked to control the same light.

6. Now you are able to control your light with two switches. Do not associate another button in the same switch for multi-control.

7. If you want to add a third or more smart switches to control your light, just repeat the steps above. You will see the result as below when you associate another new switch.

Enter MOES Skill in Alexa APP

1. Complete product networking configuration in the App

Complete the device's networking configuration according to the prompts in the App.

Note: In the App, change the name of the device to an easily identifiable name such as "bed light". Names are usually in English.

2. Configure the Amazon Echo device

(If you have already configured Amazon Echo [Alexa], you can skip this step. The following instructions are based on the iOS client.)

• Make sure your Amazon Echo device is powered on and connected to a Wi-Fi ? network.
• Open the Alexa App on your phone. After successful login, tap on the menu in the upper left corner of the Home page, select "Settings", and tap "Set Up A New Device" to set up the Amazon Echo.
• Choose your Amazon Echo device type and language for connecting. Press and hold the small dot on the device until the light turns yellow. Then tap "Continue" to connect to the hotspot.
• After connecting to the Amazon Echo hotspot, return to the page. At this point, the connection is successful.

Tap "Continue" to proceed to the next step. Choose a Wi-Fi network to connect to. Amazon Echo will take a few minutes to try to connect to the network.

After the network connection is successful, tap "Continue". An introduction video will appear. After the video ends, tap "Continue" to jump to the Alexa Home page. You have now completed the Amazon Echo's configuration process.

3. Key step - Link Skill

Tap on "Skills" in the Alexa App menu.

Then search for "MOES". Tap "Enable" to enable the Skill.

Enter the App account and password, then tap "Link Now" to link your App account and enable the Skill. Now you can start your smart home journey.

[App screen showing "Link your MOES account with Amazon" prompt]

4. Common commands

Control the device via voice commands with Echo [Alexa]. You can control your device (such as your bedroom light) with the following commands:

• Alexa, turn on/off bedroom light. (Turn on/off the light)
• Alexa, set bedroom light to 50 percent. (Set the light to any brightness)
• Alexa, brighten/dim bedroom light. (Increase/weaken the brightness of the light)
• Alexa, set bedroom light to green. (Adjust the color of the light)

Service

Thank you for your trust and support for our products. We provide a two-year worry-free after-sales service (freight is not included). Please do not alter this warranty service card to safeguard your legitimate rights and interests. If you need service or have any questions, please consult the distributor or contact us.

Product quality problems occurring within 24 months from the date of receipt should be handled by preparing the product and packaging for after-sales maintenance at the site or store where you purchased it. If the product is damaged due to personal reasons, a certain amount of maintenance fee shall be charged for repair.

We have the right to refuse to provide warranty service if:

1. Products with damaged appearance, missing LOGO, or beyond the service term.
2. Products that are disassembled, injured, privately repaired, modified, or have missing parts.
3. The circuit is burned or the data cable or power interface is damaged.
4. Products damaged by foreign matter intrusion (including but not limited to various forms of fluid, sand, dust, soot, etc.).

Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

[WEEE Symbol]

Warranty Card

Product Information

Maintenance Records

Contact Information

Thank you for your support and purchase at MoesGo. We are always here for your complete satisfaction. Feel free to share your great shopping experience with us.

⭐⭐⭐

If you have any other needs, please do not hesitate to contact us first; we will try to meet your demand.

European Representative (EC REP)

AMZLAB GmbH
Laubenhof 23, 45326 Essen
Made In China

UK Representative (UK REP)

EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292-1680945
Email: contact@evatmaster.com

Manufacturer

YUEQING NOVA ELECTRONICS CO.,LTD
Address: 3th Floor, Building 2, Power Science and Technology Innovation Center, NO. 238, Wei 11 Road, Yueqing Economic Development Zone, Wenzhou, Zhejiang, China
Tel: +86-577-62625592
After-sale Service: service@moesgo.com