MoesGo Smart Switch (Single Pole) - Instruction Manual

Product Overview

01 Product Outline

Diagram showing the smart switch components: Cover Panel, ON/OFF button, and LED Indicator.

02 Indicator Light Status

03 Specification

Power ratings:

• Incandescent: 7W ~ 800W
• LED/halogen: 7W ~ 450 W

04 Product Description

A Wi-Fi smart switch is a switchgear that can be controlled through a Wi-Fi connection, usually embedded in a wall or electrical appliance to achieve remote control, timing switch, voice control, and other functions. This kind of switch usually consists of a power processing part, a signal control part, an input signal part, and an output signal part.

Safety Information

WARNING: RISK OF ELECTRIC SHOCK

Electricity can cause personal injury and property damage if handled improperly. If you are not sure about any part of these instructions, please seek professional assistance from a qualified electrician. Ensure all work meets applicable local and national codes.

Tools you'll need

• [Phillips-head screwdriver]
• [Flat-head screwdriver]
• [Pliers]
• [Voltage tester]

Installation

07 Installation

Approximately 30 minutes to install and setup the switch

STEP 1 Turn Off Power

Locate your circuit breaker panel and turn off the power to each switch you are replacing. [Diagram of a circuit breaker panel with power off indicated].

STEP 2 Pull Out Old Switch

[Diagram showing hands pulling a switch plate away from the wall].

STEP 3 Verify Power is Off

We recommend you to remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit. You may need to turn off more than one circuit breaker. [Diagram of a hand holding a voltage tester near wires connected to an old switch].

STEP 4 Pull Out Old Switch

[Diagram showing a hand pulling an old switch out of a wall box].

STEP 5 Identify The Old Switch - Single Pole Switch

Only one switch control one light or a bundle of lights. [Diagram illustrating a single-pole switch].

STEP 6 Identify Line/Load Wire

Note: The color of your wire may be different from the color shown on the manual. LINE/LOAD wire (usually BLACK, attached with a black screw). [Diagram showing the wiring of a single-pole switch, labeling the "Line/Hot" wire and the "Load" wire].

STEP 7 Test NEUTRAL and GROUND Wires

Make sure there is no power on the neutral wires from neighboring circuit. If necessary, shut off additional circuits until no voltage is found. GROUND wires are usually BARE COPPER or GREEN. [Diagram showing wiring connections, highlighting Neutral and Ground wires].

STEP 8 Take Pictures of the Wiring

[Diagram showing a smartphone taking a picture of the wiring connections inside a wall box].

STEP 9 Wire the Smart Switch

Connection Diagram -- Single Pole

Neutral (White)

[Diagram showing connection diagram for a single-pole smart switch, illustrating how to connect Line/Hot (black), Neutral (white), and Load (red) wires to the corresponding terminals (L, N, L1, G).]

STEP 10 Mount the switch

[Diagram showing a hand pushing the smart switch into the wall box].

STEP 11 Turn on the power

[Diagram of a circuit breaker switch in the "ON" position].

Important Notes

Supercapacitor Charging

This product needs to charge the supercapacitor at the first time power-on. The charging time will take about 5~7 minutes, It will be slightly different depending on the load power and type.

Charge time: 7 mins

Flicker during charging: The light may turn on or flicker during the charging process, this is normal situation, and the light will automatically go off after the charge is completed, the switch needs about 1 more minute to initialize, and then it will enter the normal working state.

Add Devices (App Setup)

08 Add Devices

STEP 1 Download MOES App

[QR code] for downloading the MOES App. The MOES App is upgraded for better compatibility and functionality, though Tuya Smart/Smart Life apps are also supported.

STEP 2 Registration or Log in

Download the "MOES" Application. Enter the Register/Login interface; tap "Register" to create an account by entering your phone number to get verification code and "Set password". Choose "Log in" if you already have a Smart Life account.

STEP 3 Configure the APP to the switch

Preparation: Ensure the switch has been connected with electricity; ensure your phone has been connected to Wi-Fi and is able to connect to the Internet.

Note: The switch only supports 2.4G network. If you have connected 5G network, please disconnect 5G network firstly and connect 2.4G network.

STEP 4 Add the Switch to APP

Preparation: Ensure the switch has connected with electricity; ensure your phone has connected to Wifi router and is able to connect to the internet.

Note: The switch supports 2.4G Wi-Fi network only.

After the user login, Tap the [+] icon on the top right corner to add device; select the "switch" menu and choose the switch device icon. [Screenshots showing app interface for adding a device].

STEP 5 Quick Configuration Mode

Press and hold Switch button for 8s to reset the Switch and get into quick configure mode. Select the Wi-Fi and enter the password then click Next. Wait for completing the connection. [Screenshots showing Wi-Fi selection and password entry].

Remark: Smart phone and device must connect to same Wi-Fi during setup mode. The device must be added to the account before it can be controlled remotely. After the device is successfully accessed, other users can obtain control of the product through the sharing function.

STEP 6 All added devices can be viewed in the main menu of the APP

[Screenshot showing the main app menu with added devices].

STEP 7 Control switch with APP

[Screenshots showing the app interface for controlling the smart switch].

Reset

09 Reset

Press and hold Switch button for 8s to reset the Switch and get into quick configure mode. [Diagram showing a finger pressing and holding the switch button for 8s, with LED flashing].

Voice Control

10 Control your home with your voice

Control your home with your voice. Devices are compatible with Amazon Alexa and Google Home supported functionalities.

Please see our step-by-step guide on: https://www.moestech.com/blogs/news/smart-device-linked-voice-speaker

Troubleshooting

Make sure you have good Wi-Fi signal strength at the location of the switch. Metal box and MATEL Surface-wall board may block Wi-Fi signal. Make sure input correct Wi-Fi password.

Compliance

FCC Caution

FCC Compliance Statement for WS-SY-US-L110 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC Caution

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Support & Contact

Thank you for your support and purchase at we MoesGo, we are always here for your complete satisfaction, just feel free to share your great shopping experience with us.

If you have any other need, please do not hesitate to contact us first, we will try to meet your demand.

FOLLOW US

• @moessmart
• MOES.Official
• @moes_smart
• @moes_smart
• www.moes.net

Company Information

E-CrossStu-GmbH

Mainzer Landstr. 69, 60329 Frankfurt am Main

Email: E-crossstu@web.de

Tel: +4969332967674

Made in China

EVATOST CONSULTING LTD

Address: Suite 11, First Floor, Moy Road Business Centre, Taffs Well, Cardiff, Wales, CF15 7QR

Tel: +442921680945

Email: contact@evatmaster.com

WENZHOU NOVA NEW ENERGY CO.,LTD

Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China

Tel: +86-577-57186815

Email: service@moeshouse.com

Manual Folding Instructions

Text indicating the manual was printed using 200x455mm four-color printing on 80g matte paper with an accordion fold. Diagrams show a folding process.