BAGGEBO
Safety Warnings
WARNING
Children have died from furniture tipover. To reduce the risk of furniture tipover:
- ALWAYS install the anti-tip device provided.
- NEVER put a TV on this product.
- NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
Read and follow each step of the instruction carefully.
Assembly Tools and Tips
Tools required: [screwdriver], [hammer], [ruler].
Assembly may require two people. Ensure you have adequate space and a clean, protected surface for assembly.
Parts List
The following parts are included:
- 2x Screw (109558)
- 1x Screw (109041)
- 4x Screw (146114)
- 1x Screw (101068)
- 2x Dowel/Pin (106940)
- 10x Screw with spring (100229)
- 4x Dowel (101339)
- 24x Dowel (101345)
- 10x Screw/Bolt (100481)
- 1x Hex Key (100006)
- 14x Cam Lock (119252)
- 6x Dowel/Pin (122628)
- 1x Cam Lock Housing (103651)
- 1x Plastic Clip/Bracket (105494)
- 1x Bracket (319503)
- 1x Wall Bracket (106989)
- 1x Drawer Slide Part (133127)
- 1x Washer (101313)
- 2x Screw (100823)
- 1x Drawer Slide Part (139477)
- 2x Drawer Slide (10087134)
- 4x Screw (110519)
- 2x Knob (10062514)
- 2x Screw (119976)
- 2x Screw (105021)
- 2x Cam Lock (119030)
- 2x Plastic Cap (10119600)
- 2x Plastic Cap (10119658)
- 15x Nail (101206)
Assembly Steps
Step 1
Attach one metal drawer slide (part 10087134) to a side panel using two screws (part 146114). Ensure the slide is oriented correctly as shown.
Step 2
Attach the second metal drawer slide (part 10087134) to the other side panel using two screws (part 146114).
Step 3
Insert four wooden dowels (part 101339) into the designated holes on two of the main panels.
Step 4
Insert two wooden dowels (part 101345) into the designated holes on each of the two panels, for a total of four dowels.
Step 5
Attach a panel using the hex key (part 100006) and three spring-loaded screws (part 100229).
Step 6
Insert five wooden dowels (part 101345) into the designated holes on a panel.
Step 7
Attach a panel using the hex key (part 100006) and two screw/bolt components (part 100481).
Step 8
Place a panel onto another, aligning pre-drilled holes and securing with three screws (part 100823) inserted from the underside.
Step 9
Insert two cam locks (part 119252) into the designated holes on a panel. Rotate the cam locks to secure a connecting piece.
Step 10
Attach a panel using the hex key (part 100006) and two screw/bolt components (part 100481).
Step 11
Attach a panel using two wooden dowels (part 101345).
Step 12
Attach a panel using two screw/bolt components (part 100481) and two wooden dowels (part 101345).
Step 13
Insert two cam locks (part 119252) into the designated holes on a panel and rotate to secure.
Step 14
Assemble the internal dividers by sliding them into place.
Step 15
Secure the internal structure using the hex key (part 100006) and two spring-loaded screws (part 100229).
Step 16
Attach two cam locks (part 119252) and insert two dowels/pins (part 106940) into the structure.
Step 17
Insert two cam locks (part 119252) into the structure.
Step 18
Insert two cam locks (part 119252) into the structure.
Step 19
Insert four wooden dowels (part 101345) into the designated holes on a panel.
Step 20
Slide a panel into the assembled structure.
Step 21
Insert four wooden dowels (part 101345) into the designated holes on the structure.
Step 22
Secure the structure using the hex key (part 100006) and five spring-loaded screws (part 100229).
Step 23
Insert five wooden dowels (part 101345) into the designated holes on the side panels.
Step 24
Attach the wall bracket (part 106989) to the unit using two screws (part 100823) and a washer (part 101313). Ensure the bracket is oriented correctly.
Step 25
Secure a panel using the hex key (part 100006) and six screw/bolt components (part 100481).
Step 26
Attach the top panel by aligning it and securing it with dowels/pins (part 122628) using a hammer.
Step 27
Insert six cam locks (part 119252) into the designated holes and rotate to secure.
Step 28
Slide a panel into place.
Step 29
Slide a panel into place, using a ruler to guide it.
Step 30
Attach plastic clips/brackets (part 105494) using fifteen nails (part 101206) and a hammer. Ensure correct alignment.
Step 31
Attach six dowels/pins (part 122628) using a hammer.
Step 32
Attach two cam lock housings (part 103651) and secure them with two screws (part 109558) each, using a screwdriver.
Step 33
Insert two plastic caps (part 10119600) into the designated holes.
Step 34
Insert two plastic caps (part 10119658) into the designated holes.
Step 35
Attach a panel using one screw (part 101068) and one washer (part 101313) with a screwdriver.
Step 36
Attach a drawer slide part (part 139477) to the unit. Attach another drawer slide part (part 133127) to the unit.
Step 37
Attach a door using the provided hardware. Align the door and secure it.
Step 38
Attach a door using the provided hardware. Align the door and secure it with a click.
Step 39
Attach a knob (part 10062514) to the door using one screw (part 119976).
Step 40
Attach the wall bracket (part 106989) to the unit using one screw (part 100823).
Step 41
Assemble a drawer base by attaching a panel using four screw/bolt components (part 100481).
Step 42
Slide a panel into the drawer assembly.
Step 43
Insert four cam locks (part 119030) into the drawer assembly and rotate to secure.
Step 44
Slide a panel into the drawer assembly.
Step 45
Attach a panel to the drawer assembly using a hammer and four screws (part 110519).
Step 46
Attach a knob (part 10062514) to the drawer using one screw (part 119976).
Step 47
Attach the drawer slides to the main unit. Ensure correct orientation.
Step 48
Insert the assembled drawer into the unit.
Step 49
Adjust the drawer slides for proper alignment using a screwdriver.
Step 50
Secure the drawer with two screws (part 105021).
Step 51
Insert the drawer into the unit.
Final Check
Ensure all screws are tightened and the unit is stable. Follow the anti-tip device installation instructions separately if provided.
