SALUS CONTROLS Digital Programmable Thermostat

Introduction

The 091FLv2/091FLRFv2 is a programmable, weekly thermostat designed to control room temperature in heating or cooling systems. Please read this manual carefully before first use. Use only AA 1.5V alkaline batteries; do not use rechargeable batteries. Insert batteries into the slot located under the cover.

Product Compliance and Safety Information

This product complies with the following EU Directives:

• 091FLv2: 2014/30/EU, 2014/35/EU, 2011/65/EU
• 091FLRFv2: 2011/65/EU, 2014/53/EU (9) 868.0 MHz - 868.6 MHz; <13dBm

Full information is available on the website www.saluslegal.com.

Safety Information: Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Installation must be carried out by a qualified person in accordance with national and EU regulations.

Technical Specifications

Proper Thermostat Placement

Choose a suitable location for the thermostat. It should be placed on an internal wall, approximately 1.5 meters (150 cm) from the floor. Ensure there is at least 20 cm of clear space around the thermostat for accurate temperature sensing.

[Diagram: Illustration showing ideal placement of a thermostat on a wall, indicating 150 cm height from floor and 20 cm clearance.]

Button Functions

• ⬆️ (Comfort Temp): Comfort temperature or changing parameters up
• ⬇️ (Economic Temp): Economic temperature or changing parameters down
• ? (Day): Set the day of the week
• ⏰ (Hour): Set the hour
• ⏱️ (Minute): Set the minutes
• ?️ (Temp): Temperature setpoint
• ▶️ (Prog): Weekly programming
• ? (Prog #): Program selection
• ✅ (OK): Confirm function
• ? (Reset): Factory Reset

LCD Icon Description

• 1: Day of the week indicator
• 2: Heating Mode ON ?
• 3: Cooling Mode ON ❄️
• 4: Room/setpoint temperature
• 5: Temperature unit (°C/°F)
• 6: Controlled device working status (e.g., boiler ON/OFF)
• 7: Temporary override
• 8: Eco Mode ?
• 9: Program number
• 10: Antifrost Mode ❄️
• 11: Comfort Mode
• 12: Program timeline indicator
• 13: Clock ⏰
• 14: Low battery indicator ?
• 15: AM/PM

Wiring Diagrams

Wired Thermostat (091FLv2)

[Diagram: Shows the 091FLv2 thermostat with terminals labeled COM and NO, and a MAX load rating of 5(3)A. Illustrates a direct wired connection to a heating/cooling system.]

Wireless Thermostat (091FLRFv2)

[Diagram: Shows the 091FLRFv2 thermostat wirelessly connected to a receiver unit (RXRT510). The receiver has terminals COM and NO, and a MAX load rating of 16(5)A, and is powered by 230V AC. This illustrates a wireless control setup.]

Setting Time

1. Press ✅ (OK) to highlight the display.
2. Press ? (Day) to set the day of the week.
3. Press ⏰ (Hour) to set the hour.
4. Press ⏱️ (Minute) to set the minutes.
5. Press ✅ (OK) to confirm.

Setting Comfort and Economic Temperatures

To set Comfort Temperature:

1. Press ✅ (OK) to highlight the display.
2. Press ⬆️ (Comfort Temp) and then press ?️ (Temp).
3. The display shows the current comfort temperature. Press ⬆️ or ⬇️ to adjust the value.
4. Press ✅ (OK) to confirm.

To set Economic Temperature:

1. Press ✅ (OK) to highlight the display.
2. Press ⬇️ (Economic Temp) and then press ?️ (Temp).
3. The display shows the current economic temperature. Press ⬆️ or ⬇️ to adjust the value.
4. Press ✅ (OK) to confirm.

Programs

There are 9 programs available: Programs 0-5 are factory-set programs, while Programs 6-8 can be defined by the user.

Selecting Factory Programs (0-5)

1. Press ✅ (OK) to highlight the display.
2. Press ▶️ (Prog) to select the day of the week.
3. Press ? (Prog #) to set the program number (0-5) for the selected day. Program 0 is a special program that sets the thermostat to antifrost temperature (7°C) ❄️ for the entire day.
4. Press ✅ (OK) to confirm.

Note: Program descriptions are on the back of the cover.

Choosing and Programming User Programs (6-8)

1. Press ✅ (OK) to highlight the display.
2. Press ▶️ (Prog) to select the day of the week.
3. Press ? (Prog #) to set the program number (6, 7, or 8) for the selected day.
4. Press ⬆️ or ⬇️ button (each pressing moves the timeline by one hour) to assign a comfort (⬆️) or an economic (⬇️) temperature.
5. Press ✅ (OK) to confirm.

Service Menu

1. Press ✅ (OK) to highlight the display. Then hold ✅ (OK) for 5 seconds to enter the service menu.

1. Mode:
   • Heating mode ? (relay closes with delay)
   • Cooling mode ❄️ (relay closes with delay)
   Select using ⬆️/⬇️ buttons, confirm with ✅ (OK).
2. Delay:
   • Heating device delay switch disabled (default setting).
   • Heating device delay switch is ON (5 min).
   Select using ⬆️/⬇️ buttons, confirm with ✅ (OK).
3. Hysteresis:
   • Selectable values: 0.5°C or 1.0°C (default = 1.0°C).
   Select using ⬆️/⬇️ buttons, confirm with ✅ (OK).
4. Temperature Correction:
   • Adjust measured temperature by -3.0°C to +3.0°C (default = 0.0°C).
   Select using ⬆️/⬇️ buttons, confirm with ✅ (OK).
5. Terminal Output:
   • Normally Open*
   • Normally Closed*
   *Feature available from software version 2.6.Select using ⬆️/⬇️ buttons, confirm with ✅ (OK). The green LED is always ON when the relay output is short.
6. Pairing (for 091FLRFv2):
   • Pairing process inactive
   • Pairing process active ?
   NOTE! If you are using the 091FLRFv2 pack, the pairing between the thermostat and the receiver is already done.

   To re-pair thermostat with the receiver:

   1. Ensure the device is disconnected from the power supply.
   2. Set the switches on the receiver to AUTO and ON.
   3. Connect the receiver to the power supply and wait for the red LED to light steadily.
   4. Quickly switch the receiver to the OFF position, then back to the ON position. The red flashing LED will confirm entering the pairing mode.
   5. Select pairing using ⬆️/⬇️ buttons and confirm with ✅ (OK) to begin the pairing process.
   6. The display will show [pairing icon]. The pairing process may take up to 10 minutes.
   7. Once devices are successfully paired, the LED on the receiver will go solid red.
   8. Press ✅ (OK) to end the pairing process.