SALUS 091FL/091FLRF Digital Programmable Thermostat

Introduction

The SALUS 091FL/091FLRF is a programmable, weekly thermostat designed to control room temperature in heating or cooling systems. Please read this manual carefully before use. Only use AA 1.5V alkaline batteries. Do not use rechargeable batteries. Batteries are located in the slot under the cover.

Product Compliance

This product complies with the following EU Directives:

• 091FL: 2014/30/EU, 2014/35/EU, 2011/65/EU
• 091FLRF: 2011/65/EU, 2014/53/EU (868.0 MHz - 868.6 MHz; <13dBm)

Full information is available at www.saluslegal.com.

Safety Information

Use the device in accordance with national and EU regulations. Use only as intended and keep it dry. This product is for indoor use only. Installation must be performed by a qualified person according to national and EU regulations.

Technical Specifications

Wired Thermostat 091FL

Wireless Thermostat 091FLRF

Proper Thermostat Placement

Diagram showing ideal thermostat placement on a wall, approximately 150 cm from the floor and at least 20 cm from corners or heat sources.

Button Functions

LCD Icon Description

Description of icons displayed on the thermostat screen:

• 1. Day of the week indicator
• 2. Heating Mode ON
• 3. Cooling Mode ON
• 4. Room/setpoint temperature
• 5. Temperature unit (°C)
• 6. Controlled device working status (e.g., boiler)
• 7. Temporary override
• 8. Eco Mode
• 9. Program number
• 10. Antifrost Mode
• 11. Comfort Mode
• 12. Program timeline indicator
• 13. Clock
• 14. Low battery indicator ?
• 15. AM/PM

Wiring Diagrams

091FL Wiring Diagram

Diagram shows connections for the wired thermostat 091FL. Terminals: L (Live), N (Neutral), COM (Common), NO (Normally Open). The MAX terminal indicates the maximum load rating.

091FLRF Wiring Diagram

Diagram shows connections for the wireless thermostat 091FLRF receiver (RXRT510). Terminals: L (Live), N (Neutral), COM (Common), NO (Normally Open). The MAX terminal indicates the maximum load rating.

Changing Communication Code (091FLRF)

To prevent interference from other wireless devices, it is recommended to change the communication code from the factory setting. Use DIP switches (numbered 1-5) on both the receiver and transmitter. Ensure they are in the same position on both units. Press the Reset button after changing the code.

Setting Time

Press OK to highlight the display. Use D to set the day, H to set the hour, and M to set the minutes. Press OK to confirm.

Setting Temperatures

Comfort Temperature

Press OK to highlight. Use the [increase] and [decrease] buttons to adjust the current comfort temperature. Press OK to confirm.

Economic Temperature

Press OK to highlight. Use the [increase] and [decrease] buttons to adjust the current economic temperature. Press OK to confirm.

Programming

There are 9 available programs: Programs 0-5 are factory pre-set, and Programs 6-8 can be user-defined.

Selecting Factory Programs (0-5)

Press OK to highlight. Use the Prog button to select the day of the week. Use Prog # to set the program number (0-5) for the selected day. Program 0 sets the thermostat to antifrost temperature (7°C) for the entire day. Press OK to confirm.

Choosing and Programming User Programs (6-8)

Press OK to highlight. Use the Prog button to select the day of the week. Use Prog # to set the program number (6, 7, or 8) for the selected day. Use the [increase] and [decrease] buttons to adjust the timeline by one hour, assigning either a comfortable or an economic temperature for that hour. Press OK to confirm.

Note: A label with program descriptions is located on the flip side of the cover.

Service Menu

Press OK to highlight the display. Hold the OK button for 5 seconds to enter the service menu.

• Mode: Heating (relay closes when heating is needed) or Cooling (relay closes with a 5-minute delay). Select using [increase]/[decrease] buttons and confirm with OK.
• Heating Device Delay Switch: DLY OFF (disabled) or DLY ON (5 min delay). Select using [increase]/[decrease] buttons and confirm with OK.
• Temperature Span: Select between 0.5°C or 1.0°C (default 1.0°C). Use [increase]/[decrease] buttons and confirm with OK.
• Temperature Correction: Adjust measured temperature by -3.0°C to +3.0°C (default 0.0°C). Use [increase]/[decrease] buttons and confirm with OK. (Feature available from software version 2.4).