NYSJÖN Wash-Basin Cabinet

Important Safety Information

⚠️ WARNING!

Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

(Note: Safety warnings are provided in multiple languages throughout the original document.)

Parts List

Before starting assembly, check that you have all the parts listed below. The numbers in parentheses refer to the part numbers shown in the diagrams.

8x Dowel (part 123492)
8x Dowel (part 101375)
1x Screw (part 119976)
8x Screw (part 124386)
4x Screw (part 124431)
8x Cam Lock (part 102509)
8x Screw (part 10048881)
2x Corner Bracket (part 10043491)
4x Bracket (part 10032274)
4x Bracket (part 153647)
4x Side Panel Bracket (part 10043569)
1x Cap (part 106266)
1x Cover Cap (part 107091)
2x Hinge (part 144553)
2x Leg Support (part 10068747)
2x Runner (part 10059781)
2x Leg (part 10056734)

Required tool: Drill with a Ø 5 mm (3/16") drill bit.

Assembly Instructions

Step 1

Attach brackets to side panels.

Attach four brackets (part 10032274) to the designated holes on each side panel using eight screws (part 10048881) in total (4 screws per panel).

Step 2

Attach corner brackets to base panel.

Attach two corner brackets (part 10043491) to the underside of the base panel using four screws (part 124386) in total (2 screws per bracket). Also, attach two brackets (part 10043491) to the side panels using screws (part 124386) and (part 124431).

Step 3

Insert dowels into side panels.

Insert eight dowels (part 123492) into the pre-drilled holes on the edges of the two side panels. Gently tap them in if necessary.

Step 4

Insert dowels into base panel.

Insert eight dowels (part 101375) into the pre-drilled holes on the top surface of the base panel.

Step 5

Attach side panels to the base.

Align the side panels vertically with the base panel, ensuring the dowels fit into the corresponding holes.

Step 6

Secure side panels with cam locks.

Insert eight cam locks (part 102509) into the large holes on the inside of the side panels. Rotate the cam locks ? using a screwdriver ? to secure the side panels to the base panel.

Step 7

Attach the top panel.

Place the top panel onto the assembled structure, aligning it with the side panels and ensuring any dowels or connectors fit correctly.

Step 8

Secure the top panel with cam locks.

Insert four cam locks (part 102509) into the large holes on the inside of the top panel. Rotate the cam locks ? using a screwdriver ? to secure the top panel to the side panels.

Step 9

Attach drawer runners to side panels.

Attach two runners (part 10059781) to the inside of each side panel using screws (part 124431). Ensure they are level and correctly positioned.

Step 10

Attach drawer runners to the other side panel.

Attach the remaining two runners (part 10059781) to the inside of the other side panel using screws (part 124431). Ensure they are level and correctly positioned.

Step 11

Attach legs.

Attach the two leg supports (part 10068747) to the underside of the base panel using screws (part 124386). Then, screw the two legs (part 10056734) into the leg supports.

Step 12

Attach hinge mounting plates to cabinet body.

Attach four hinge mounting plates (part 153647) to the inside of the cabinet body (two on each side panel) using screws (part 124386).

Step 13

Attach hinges to doors.

Attach two hinges (part 144553) to the inside of each door using screws (part 124386).

Step 14

Attach hinge arms to cabinet body.

Attach two hinge arms (part of 144553) to the cabinet body on each side, using screws (part 124386). These attach to the previously installed hinge mounting plates.

Step 15

Attach remaining hinge arms to cabinet body.

Attach the remaining two hinge arms (part of 144553) to the cabinet body on the other side, using screws (part 124386).

Step 16

Attach the decorative top piece.

Attach the decorative top piece (part 10043569) to the top front edge of the cabinet. It slots into place.

Step 17

Attach hinges to doors (detail).

This step shows a close-up of attaching the hinge mechanism (part 144553) to the door using screws (part 124386).

Step 18

Attach doors to the cabinet.

Align the hinges on the doors with the hinge mounting plates on the cabinet body and click them into place. The diagram shows how to insert the hinge arm into the hinge plate and secure it.

Step 19

Prepare for wall attachment and drill holes.

The diagram shows using a clamp to mark drilling points on the wall. Drill holes with a Ø 5 mm (3/16") drill bit to a depth of 30mm (1 1/4"). ⚠️ Warning: Do not drill into pipes or electrical wires.

Step 20

Attach handle/knob.

Attach the handle or knob (part 106266) to the door using the screw (part 119976). The screw passes through the door from the inside into the knob.

Step 21

Attach cover caps.

Attach two cover caps (part 107091) to the designated holes on the cabinet.

Step 22

This page contains only the page number.

Step 23