NYSJÖN Vanity Unit

Important Safety Information ⚠️

Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided. Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instructions carefully.

Parts Included

• Dowel (123492) - 12x
• Dowel (101375) - 12x
• Screw (119976) - 2x
• Screw (124431) - 8x
• Cam Lock (102509) - 12x
• Screw (10048881) - 4x
• Wall Bracket Cover (10043569) - 2x
• Mounting Bracket (10032274) - 2x
• Hinge Mounting Plate (153647) - 2x
• Hinge Cover (106266) - 2x
• Decorative Cap (107091) - 2x
• Mounting Bracket (10068747) - 4x
• Hollow Tube (10059781) - 4x
• Leg Support (10056734) - 4x
• Hinge (144553) - 4x

Assembly Instructions

Step 1

Attach two mounting brackets (10032274) to a base panel using four screws (10048881) in total (two per bracket).

Step 2

Insert twelve dowels (123492) into the pre-drilled holes on the base panels.

Step 3

Insert twelve dowels (101375) into the pre-drilled holes on the two vertical side panels.

Step 4

Place the two vertical side panels onto the base panel, aligning the dowels with the corresponding holes.

Step 5

Secure the side panels to the base panel using twelve cam locks (102509). Insert cam locks into the side panels and rotate them to engage with the base panel's fittings.

Step 6

Place the top panel onto the assembled side panels.

Step 7

Secure the top panel using twelve cam locks (102509), similar to Step 5.

Step 8

Insert four dowels (101375) into the pre-drilled holes on the back panel.

Step 9

Screw four threaded inserts (123492) into the designated holes on the bottom panel to serve as feet.

Step 10

Slide the back panel into the grooves on the side and top panels.

Step 11

Secure the back panel using twelve cam locks (102509).

Step 12

Attach four mounting brackets (10068747) to the outer sides of the cabinet using eight screws (124431) in total (two per bracket).

Step 13

Attach four leg supports (10056734) to the bottom of the cabinet.

Step 14

Screw the adjustable feet into the leg supports and adjust them to level the cabinet. ↔️⬆️⬇️

Step 15

Attach two hinge mounting plates (153647) to the inside of each cabinet door.

Step 16

Prepare for wall attachment. Note: Screws and plugs for the wall are not included and must be purchased separately, suitable for your wall type. ?

Step 17

Attach two hinge mounting plates (153647) to the inside of the cabinet frame.

Step 18

Attach two door handles/covers (10043569) to each cabinet door.

Step 19

Assemble four hinges (144553) onto the hinge mounting plates attached to the doors.

Step 20

Attach the cabinet doors to the frame by aligning the hinges with the mounting plates on the frame and securing them. ➡️

Step 21

Attach two hinge covers (106266) to the hinges. Secure the hinges to the cabinet frame using two screws (119976).

Step 22

Place two decorative caps (107091) over the hinge screws on the inside of the cabinet.

Hinge Adjustment ⚙️

The hinges allow for precise adjustment of the doors:

• Horizontal Adjustment: Use the designated screw to move the door left or right. ↔️
• Vertical Adjustment: Use the designated screw to move the door up or down. ⬆️⬇️
• Depth Adjustment: Use the designated screw to move the door in or out. ➡️⬅️