HS-DS100+ Z-Wave Door / Window Sensor
Brand: HomeSeer
Overview
The HS-DS100+ is a battery-operated sensor designed to issue Z-Wave commands when doors or windows are opened or closed. It can be associated directly with other Z-Wave devices or used with a wide variety of Z-Wave hubs and controllers to trigger events, scenes, and other automations.
Operation
The HS-DS100+ comprises a sensor body and a magnet piece. The sensor body is typically installed on a door or window jamb, while the magnet piece is installed on the door or window. When the door or window is closed, the magnet trips a switch inside the sensor body, issuing a Z-Wave command. When the door or window is opened, the switch is tripped again, issuing another Z-Wave command.
Physical Installation
The sensor body and magnet piece must be mounted to the door or window (vertically or horizontally) using the provided screws or double-stick tape. Ensure a gap of no wider than 10mm to allow the door or window to open and close easily without obstruction.
If using screws, first mount the backing plates of the sensor body and magnet pieces. To remove the sensor body backing plate, press the latch button and gently pry it off. To remove the magnet piece backing plate, use a small slotted screwdriver.
Z-Wave Network Installation
The Door/Window Sensor can be included and operated in any Z-Wave network with other Z-Wave certified devices. All non-battery operated nodes within the network will act as repeaters, increasing network reliability.
Inclusion
- Ensure AAA batteries are installed. Remove any plastic from the battery compartment if necessary.
- Put your home automation controller into 'inclusion' mode. Consult your system's manual for details.
- Triple-click the Z-Wave button inside the sensor body. Wait for the process to finish.
- If successful, the sensor body LED will blink briefly and then stay on for 3 seconds. If unsuccessful, the LED will blink briefly and then turn off. Repeat the inclusion process if unsuccessful.
Note: For secure/encrypted Z-Wave communications, a security-enabled Z-Wave controller is required.
Exclusion
- Put your home automation controller into 'exclusion' mode. Consult your system's manual for details.
- Triple-click the Z-Wave button inside the sensor body. If successful, the LED will turn off within 1 second. If unsuccessful, the LED will blink for 5 seconds. Repeat the exclusion process if unsuccessful.
Reset
- Press and hold the Z-Wave button inside the sensor body for 20 seconds. The LED will stay on until the button is released.
Z-Wave Association Information
The HS-DS100+ supports Group 1 and Group 2 associations. Group 1 reports the sensor's condition, battery level, and tamper state. Group 2 sends the BASIC SET command.
Battery Information
The HS-DS100+ is designed to report its battery condition once every 24 hours. A battery level report can also be manually invoked by pressing the Z-Wave button.
S2 Security
The HS-DS100+ supports Z-Wave S2 security in unauthenticated mode.
Additional Information
Please visit our website for the latest information about HS-DS100+: https://homeseer.com/support-home/
Advanced Configuration
| Parameter | Settings |
|---|---|
| 15 | Value of BASIC SET
0 - Default 1 byte - Parameter size |
| 32 | Defines value of LOW BATTERY
20 - Default 1 byte - Parameter size |
Specifications
| Operating Temp Range | 0°C to 40°C |
| Z-Wave Frequency | Range | 908 MHz (US) | Up To 300 Ft line of sight |
| Z-Wave Certification | Z-Wave Plus |
| Power Supply | Requires (2) AAA 1.5V Batteries |
| Dimensions |
|
Limited Warranty
HomeSeer Technologies, LLC will repair or replace, at its option, any part of the device, which proves to be defective in workmanship or material under normal use, in the USA except in the states of Alaska or Hawaii, for a period of one year from the date the device is purchased. During the warranty period, HomeSeer Technologies, LLC will repair and provide all parts necessary to correct such defects, free of charge, provided the device has been operated in accordance with the manufacturer's guidelines. The Customer will return the device to HomeSeer Technologies, LLC for testing and repair or replacement. Should you need service, during warranty period or beyond, contact HomeSeer to obtain return authorization before shipping your device to HomeSeer Technologies, LLC.
Patents
This product employs or practices certain features and/or methods of the following U.S. Patents: U.S. Patent Nos. 6,891,838, 6,914,893 and 7,103,511.
