Reaper Extreme VTX - Product Overview and Specifications
Manufacturer: Foxeer
Product Specifications
- Size: 36*27.5*8mm
- Connector: MMCX
- Display: 3LED
- Weight: 13g
- Power Output Options: 25mW, 200mW, 500mW, 1.5W, 2.5W
- Input Voltage: 9~36V
- Output Voltage: 5V
- Channels: 72CH
- Protocol Support: Tramp
LED Indicator Guide
| LED | Description |
|---|---|
| Red | Power |
| Green | Channel |
| Blue | Band |
Button Operation Guide
- Channel Select Mode:
- Short click the button to enter CHANNEL setup. The green LED will flash. Select the desired channel using short presses.
- Band Select Mode:
- Press and hold the button for 3 seconds to enter BAND setup. The blue LED will turn on and flash. Select the desired band using short presses.
- Power Select Mode:
- Press and hold the button for another 3 seconds (total 6 seconds from start) to enter POWER setup. The red LED will turn on and flash. Select the desired power output using simple short presses.
Frequency Table
The following table details the frequencies available for each band and channel:
| Band | CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
|---|---|---|---|---|---|---|---|---|
| Band A | 5865 | 5845 | 5825 | 5805 | 5785 | 5765 | 5745 | 5725 |
| Band B | 5733 | 5752 | 5771 | 5790 | 5809 | 5828 | 5847 | 5866 |
| Band E | 5705 | 5685 | 5665 | 5645 | 5885 | 5905 | 5925 | 5945 |
| Band F | 5740 | 5760 | 5780 | 5800 | 5820 | 5840 | 5860 | 5880 |
| Band R | 5658 | 5695 | 5732 | 5769 | 5806 | 5843 | 5880 | 5917 |
| Band H | 5653 | 5693 | 5733 | 5773 | 5813 | 5853 | 5893 | 5933 |
| Band L | 5333 | 5373 | 5413 | 5453 | 5493 | 5533 | 5573 | 5613 |
| Band U | 5325 | 5348 | 5366 | 5384 | 5402 | 5420 | 5438 | 5456 |
| Band O | 5474 | 5492 | 5510 | 5528 | 5546 | 5564 | 5582 | 5600 |
| Power(mW) | PIT | 25 | 200 | 500 | 1.5W | 2.5W |
Advanced Features
Unlock Frequencies and Power Levels
To unlock all available frequencies and power levels: Long press the "KEY" button. Observe the Red LED (PWR). It will turn constant on, then turn off, and then turn on again. Release the button at this point. A flashed Red LED indicates that the device is in an unlocked status. A constant Red LED indicates that the device is in a locked status.
PIT Mode
PIT Mode allows the VTX to output extremely low power, useful for testing or short-range operation. To turn PIT Mode on or off: Double-click the "KEY" button. When the Red LED (PWR) is off, PIT mode is active. When the Red LED (PWR) is on, PIT mode is inactive.
Important Notes
If a Tramp cable is connected between the VTX and the flight controller, the physical button on the VTX will not function. In this configuration, frequency and power adjustments must be made via the flight controller's software.
