Package Contents
- 1 x 4G LTE Router
- 1 x Power Adapter
- 1 x Quick Installation Guide
- 1 x Ethernet Cable
Quick Installation
Install the cellular antennas.
Diagram Description: The router features four antenna connectors on its rear. The illustration shows four antennas being attached to these connectors. Labels indicate "Install the Antenna" and the location of the "Nano SIM" slot.
Insert the Nano SIM card into the SIM1 slot until you hear a click.
Diagram Description: Displays three SIM card sizes: Nano SIM (4FF), Micro SIM (3FF), and Mini SIM (2FF). The Nano SIM is marked with a checkmark, while Micro and Mini SIMs are marked with an 'X'.
Direction: With the gold contacts facing down, gently slide the SIM card into the slot.
Note: If both SIM1 and SIM2 card slots are populated with SIM cards, the router will automatically select which SIM card to use. For initial setup, it is strongly recommended to insert only one card.
Connect the power adapter to the router.
Diagram Description: Shows the rear panel of the router with ports labeled 1, 2, 3, 4. The power adapter connects to port 4. A button labeled "Press the power button" is also highlighted.
Turn on the router. Wait 2~5 minutes for it to start.
Check the status of the LED.
- LED turns to solid blue: Connected to cellular network, strong signal.
- LED turns to solid purple: Connected to cellular network, average signal.
- LED turns to solid red: Refer to "Customize the 4G Router" section.
Note: For some ISP SIM cards, internet connection may take longer. Please wait an additional 2~5 minutes.
Customize the 4G Router
Connect the router via ethernet cable or Wi-Fi. Network name and password are printed on the bottom of the router.
Diagram Description: Illustrates the router with its network name (Wi-Fi: Cudy-XXXX, Wi-Fi: Cudy-XXXX-5G) and Password (XXXXXXXX) printed on the underside.
Launch a web browser and enter http://cudy.net/ (or http://192.168.10.1/) in the address bar, use admin as password to login.
Diagram Description: Depicts a login screen with fields for username (pre-filled with 'admin') and password, accompanied by a 'Log In' button.
If your SIM card needs PIN to unlock, enter your PIN and click Save & Apply, then wait 15 seconds to connect to the Internet.
Diagram Description: A "4G Settings" pop-up window prompts for a PIN code, featuring a "Save & Apply" button.
Check 4G information card of the status page. If the status is connected, means connected to the internet successfully.
Diagram Description: Displays two status cards. One "4G" card shows "Connected" with RSSI and Upload/Download details, while another "4G" card shows "Not connected".
If 4G is not connected, or if you want to customize the router yourself, click "Quick Setup" and follow the step-by-step instructions.
Diagram Description: Shows a "Status" menu with "Internet: Not connected", "Work Mode: 4G Router", "Model: XXXXX", and a "Quick Setup" button.
Notes:
- If unsure about APN parameters, contact your internet provider.
- For other problems, contact technical support team: support@cudy.com
- Frequently Asked Questions: https://www.cudy.com/faq
LED and Button Status
| Name | Status | Indication |
|---|---|---|
| Power Icon | Off | Not powered on |
| Flash | System startup process or upgrade process | |
| Solid | System startup is complete | |
| Wi-Fi Icon | Off | Not powered on |
| Red | No internet connection | |
| Purple | 2G/3G connected | |
| Blue | 4G connected | |
| Wi-Fi Signal Icon | Off | Wi-Fi is disabled |
| Flash | WPS pairing | |
| Solid | Wi-Fi is enabled | |
| SIM Card Icon | Off | Not detect the SIM card |
| Signal Strength Icon | Red | Not connected to 4G network |
| Purple | 4G LTE signal is average | |
| Blue | 4G LTE signal is strong | |
| LAN LED | Off | No connection |
| On | Connected | |
| Power Button | Press for "Power ON", bounce for "Power OFF" | |
| WPS Button | Press to take effect. | |
| Reset Button | Long press for 2s to take effect without releasing it. When it takes effect, all LED lights flash 3 times, and then enter the restart process. |
How to Upgrade Firmware
- Download the latest firmware from https://www.cudy.com/download
- Unzip the file.
- Connect to Cudy's network via WiFi or Ethernet.
- Open a web browser and go to http://cudy.net/ or http://192.168.10.1/
- Log in to the web management page.
- Click Advanced Settings -> Firmware.
- Choose the firmware file you unzipped to upload.
Diagram Description: Presents the "Firmware Upgrade" interface, including fields for "Firmware File Path" and a "Browse..." button. A table lists "NO.", "Mesh Unit", "Model", and "Firmware Version" (e.g., 1, Main route, XXXX, 1.11.0).
- Wait 2~5 minutes for the router restart.
- Done.
Need Help?
Q1. What should I do if I cannot access the web management page?
- A1: If the computer is set to a static IP address, change its settings to obtain an IP address automatically.
- A2: Make sure http://cudy.net/ or http://192.168.10.1/ is correctly entered in the web browser.
- A3: Use another web browser and try again.
- A4: Reboot your router and try again.
- A5: Disable and enable the active network adapter in use.
Q2. How do I restore the router to its factory default settings?
- A1: With the router powered on, press and hold the RESET button for 6 seconds before release. Wait the router resets.
- A2: Log in to the web management page of the router, and go to Advanced Settings > Reset, click Perform Reset and wait until the reset process is complete.
Q3: What can I do if I meet other problems?
- A1: Find answers on https://www.cudy.com/faq
- A2: Contact cudy technical support team via email: support@cudy.com
- A3: Contact cudy technical support team via Skype: support@cudy.com
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
EU Declaration of Conformity
Cudy hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.cudy.com/ce.
