Item Number: 6910635
WARNING (To reduce the risk of fire, electric shock, or personal injury):
Safety Instructions & Precautions
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
Finished Product Appearance
The finished product is a chandelier-style lighting fixture with multiple arms and lampshades.
Tools Required (Not Included)
Before starting assembly and installation, please prepare the needed tools:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts List
| Part | Description | Quantity |
|---|---|---|
| C | Mounting plate | 1 |
| D | Green ground screw | 1 |
| E | Canopy | 1 |
| F | Swivel joint | 1 |
| G | Knob nut | 2 |
| H | Tube | [Variable Quantity] |
| I | Arm assembly | 1 |
| J | Arm | 5 |
| K | Socket assembly | 5 |
| L | Screw | 15 |
| M | Lampshade | 5 |
Accessories Enclosed
| Part | Description | Quantity |
|---|---|---|
| A | Plastic wire connector | 3 |
| B | Mounting screw | 2 |
| L | Screw (spare part) | 1 |
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustrations.
- Turn off power: Before starting installation, ensure electricity is shut off at the main fuse/circuit breaker and the wall switch is in the “OFF” position.
- Unscrew knob nuts (G) from the canopy (E) and gently remove the mounting plate (C).
- Adjust Hanging Height:
- Choose tubes (H) according to your desired hanging height.
- Pass the fixture wires through the chosen tubes (H), swivel joint (F), and canopy (E).
- Screw the chosen tubes (H) into the swivel joint (F) and the top of the arm assembly (I), then hand-tighten until snug.
- Attach the mounting plate (C) to the outlet box using mounting screws (B).
- Make Wire Connections:
Connect wires as shown in the diagrams. Ensure the ground wire is bare copper wire; never connect other wires to ground wires.
Ground Wire Connection:
Connect the fixture's ground wire to the outlet box's ground screw. This is typically done using the green ground screw (D). Ensure a secure connection.
Power Wire Connection:
Connect Black or Red Supply Wire to: Connect White Supply Wire to: Black (*Parallel cord: round & smooth; Clear, Brown, Gold or Black without tracer; Insulated wire (other than green) with copper conductor) White (*Parallel cord: square & ridged; Clear, Brown, Gold or Black with tracer; Insulated wire (other than green) with silver conductor) Note on Parallel Wires (SPT I & SPT II): The neutral wire is typically square-shaped or ridged, while the other wire is round or smooth.
Twist wires together with plastic wire connectors (A) until tightly joined. Wrap each connector with approved electrical tape. Ensure no wire strands are exposed, then carefully tuck all wires into the outlet box.
- Raise the canopy (E) to the ceiling and secure it in place by tightening knob nuts (G) onto the pre-assembled screws in the mounting plate (C). The canopy (E) should be snug against the ceiling. If not, adjust the threaded length on the mounting plate (C) by unscrewing/screwing the pre-assembled hex nuts and screws.
- Attach Lampshades:
- Remove screws (L) from socket assemblies (K).
- Align the holes of the lampshades (M) with the holes of the socket assemblies (K) and secure them with screws (L).
- Install bulbs (Not included). Do not exceed the maximum wattage recommended on the socket (Type A, Max 60W per bulb).
- Check that everything is installed properly, then turn on the light. Enjoy!
Ordering Parts
Keep this sheet for future reference if replacement parts are needed. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustrations when ordering parts.
Cleaning Instructions
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.
