IKEA MALM Dressing Table
Important Safety Information
⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.
ALWAYS secure this furniture to the wall using the provided tip-over restraints.
To further reduce the risk of serious injury and death from tip-overs:
- Place heaviest items in the lower drawer.
- Do not set TVs or other heavy objects on top of this product.
- Never let children climb or hang on drawers, doors, or shelves.
Always follow the specific wall-mounting instructions for your wall type.
Parts and Hardware
The following parts and hardware are included. Please check that you have all items before assembly.
Main Components:
- Top Panel (with glass surface)
- Side Panels (2x)
- Base Panel
- Back Support Panel
- Drawer Fronts (2x)
- Drawer Sides (4x)
- Drawer Backs (2x)
- Drawer Bottoms (2x)
- Drawer Slides (4x sets)
Hardware and Accessories:
- 114334: Large screws (4x)
- 101353: Wooden dowels (2x)
- 101345: Wooden dowels (2x)
- 110519: Cam lock bolts (4x)
- 118331: Cam lock bolts (2x)
- 100349: Small screws (4x)
- 109558: Small screws (2x)
- 110630: Cam locks (2x)
- 10003193: Mounting brackets (3x)
- 109560: Screws (3x)
- 105344: Screws (2x)
- 122998: Drawer slide runners (4x)
- 114254: Drawer slide runners (4x)
- 153548: Drawer front supports (4x)
- 113453: Wrench (1x)
- 10139504: Wall mounting bracket (1x)
- 118250: Wall mounting bracket (1x)
- 109049: Screws (2x)
- 100823: Screws (4x)
- 109048: Screws (2x)
- 106989: Wall bracket screws (2x)
- 121714: Wall plugs/anchors (2x)
- 326949: Wall plugs/anchors (2x)
- 152123: Drawer support rod (1x)
Tools Required (Not Included):
- Phillips head screwdriver
- Hammer
- Drill (for wall mounting)
Assembly Steps
Step 1: Prepare Top Panel
Attach the mounting brackets (152123) to the underside of the top panel. Use the wrench (113453) and four screws (114334).
Parts used:
- 152123 (1x)
- 114334 (4x)
- 113453 (1x)
Step 2: Attach Drawer Slides to Side Panels
Attach the drawer slide runners (10139504 and 10139543) to the inner sides of the two side panels. Use screws (100349) and (109049).
Parts used:
- Side Panels (2x)
- 10139504 (2x)
- 10139543 (2x)
- 100349 (4x)
- 109049 (2x)
Step 3: Attach Side Panels to Base
Insert wooden dowels (101353) into the base panel. Attach the side panels to the base panel, securing them with screws (100349).
Parts used:
- Base Panel
- Side Panels (2x)
- 101353 (2x)
- 100349 (4x)
Step 4: Attach Drawer Slide Runners to Base
Attach the drawer slide runners (122998 and 114254) to the base panel. Use the wrench (113453) for tightening.
Parts used:
- Base Panel
- 122998 (4x)
- 114254 (4x)
- 113453 (Wrench)
Step 5: Secure Side Panels to Base
Use a hammer to gently tap the side panels into place on the base, ensuring dowels are aligned. Secure with screws (153548).
Parts used:
- Side Panels (already attached in Step 3)
- Base Panel
- 153548 (4x)
- Hammer (tool)
Step 6: Attach Wall Mounting Bracket to Side Panel
Attach the wall mounting bracket (106989) to the top of one side panel. Use screws (109049) and (100823).
Parts used:
- Side Panel
- 106989 (2x)
- 109049 (2x)
- 100823 (4x)
Step 7: Apply Protective Film
Apply protective film (indicated by arrows) to the edges of the main unit.
Parts used:
- Protective film (if included)
Step 8: Place Top Panel
Carefully place the top panel onto the assembled base and side panels. Ensure it aligns correctly.
Parts used:
- Top Panel
- Assembled base and side panels
Step 9: Attach Support Brackets
Attach three support brackets (10003193) to the underside of the top panel using screws (109560).
Parts used:
- Top Panel
- 10003193 (3x)
- 109560 (3x)
Step 10: Attach Back Support
Slide the back support panel into place and secure it. The diagram shows a rotation action, implying it slots into place.
Parts used:
- Back Support Panel
Step 11: Attach Drawer Slide Runners to Side Panels (Second Set)
Attach the second set of drawer slide runners (122998 and 114254) to the inner sides of the side panels. Use screws (109048).
Parts used:
- Side Panels
- 122998 (4x)
- 114254 (4x)
- 109048 (2x)
Step 12: Mark Wall for Mounting
Hold the assembled unit against the wall and mark the desired height for the wall mounting bracket. Ensure the unit is level.
Tools used:
- Pencil (for marking)
- Level (recommended)
Step 13: Wall Mounting Preparation
Prepare the wall for mounting the bracket. The diagram shows different wall types (A, B, C) and corresponding hardware.
Refer to page 17 for detailed wall type instructions.
- For solid walls (A): Use screws (8 mm (5/16")) directly.
- For hollow walls (B): Use wall plugs/anchors (121714 or 326949) with screws (8 mm (5/16")).
- For solid wood (C): Use screws (3 mm (1/8")) without plugs.
Step 14: Attach Wall Bracket to Wall
Secure the wall mounting bracket (10139504 or 118250) to the wall at the marked position using appropriate screws and wall plugs for your wall type.
Parts used:
- 10139504 or 118250 (1x)
- Appropriate screws and wall plugs (from Step 13)
Step 15: Attach Drawer Front Supports
Attach the drawer front supports (153548) to the drawer sides using screws (118331).
Parts used:
- Drawer Sides (2x)
- 153548 (4x)
- 118331 (2x)
Step 16: Assemble Drawer Sides and Bottom
Attach the drawer sides to the drawer bottom. Insert wooden dowels (101345) into the drawer sides and secure with screws.
Parts used:
- Drawer Sides (2x)
- Drawer Bottom
- 101345 (2x)
- Screws (quantity not specified, assume 4x based on diagram)
Step 17: Attach Cam Locks to Drawer Sides
Insert cam locks (110630) into the designated holes on the drawer sides.
Parts used:
- Drawer Sides
- 110630 (2x)
Step 18: Attach Drawer Bottom
Slide the drawer bottom into the grooves of the drawer sides and front support. Secure with screws (105344).
Parts used:
- Drawer Bottom
- Drawer Sides
- Drawer Front Support
- 105344 (1x)
Step 19: Attach Drawer Back
Slide the drawer back panel into place and secure it. The diagram shows a rod (152123) being inserted.
Parts used:
- Drawer Back Panel
- 152123 (1x)
Step 20: Insert Drawer into Frame
Carefully slide the assembled drawer into the main unit, aligning the drawer slides.
Parts used:
- Assembled Drawer
- Main Unit
Step 21: Attach Drawer Front
Attach the drawer front to the drawer assembly. Use cam lock bolts (110519) and secure with cam locks.
Parts used:
- Drawer Front
- Drawer Assembly
- 110519 (4x)
- Cam locks (already inserted in Step 17)
Step 22: Secure Drawer Front
Secure the drawer front further using screws (105344) from the inside of the drawer.
Parts used:
- Drawer Front
- Drawer Assembly
- 105344 (1x)
Step 23: Assemble Drawer Interior
Assemble the inner part of the drawer, likely involving sliding in a base or divider.
Parts used:
- Drawer interior components
Step 24: Insert Drawer into Main Unit
Slide the fully assembled drawer into the main unit. The diagram shows a mechanism for insertion and alignment.
Parts used:
- Assembled Drawer
- Main Unit
Step 25: Final Drawer Adjustment
Adjust the drawer front alignment using screws (109558) on the drawer slides.
Parts used:
- Drawer
- Main Unit
- 109558 (2x)
Wall Mounting Instructions
For safety, it is crucial to secure the furniture to the wall using the provided anti-tip restraints. Refer to the diagrams on pages 16 and 17 for detailed instructions based on your wall type.
Wall Types:
- Type A (Solid Walls): Use screws directly into the wall.
- Type B (Hollow Walls): Use wall plugs/anchors (121714, 326949) with screws.
- Type C (Solid Wood): Use screws without plugs.
If you are uncertain about your wall type or the correct mounting procedure, seek professional advice.
External Links for more information:
YouTube
