IKEA MALM Dressing Table Assembly Instructions
Model: MALM Dressing table
Article Number: AA-2192219-11
Important Safety Information
⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.
ALWAYS secure this furniture to the wall using the provided tip-over restraints.
To further reduce the risk of serious injury and death from tip-overs:
- Place heaviest items in the lower drawer.
- Do not set TVs or other heavy objects on top of this product.
- Never let children climb or hang on drawers, doors, or shelves.
For detailed wall mounting instructions, refer to pages 16-18 of this document.
Tools and Hardware
Tools required:
- Screwdriver (cross head ?)
- Hammer ?
- Drill
- Measuring tape
- Pencil
Included hardware: A comprehensive set of screws, dowels, cam locks, brackets, and a wrench is provided. Specific quantities and part numbers are indicated in each assembly step.
Wall mounting hardware: Screws and plugs are supplied for most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If you are uncertain about your wall type or the correct installation method, seek professional advice.
Assembly Instructions
Step 1: Prepare Base Panel
Insert 4x screws (part 114334) into the pre-drilled holes on the underside of the base panel. Use the wrench (part 113453) to tighten them.
Step 2: Attach Drawer Slides to Side Panels
Attach 2x drawer slides (part 118250) and 2x drawer slides (part 100349) to the inner sides of the two vertical side panels using 4x screws (part 100349).
Step 3: Insert Dowels into Base Panel
Insert 2x dowels (part 101353) into the corresponding holes on the base panel.
Step 4: Assemble Main Frame
Connect the side panels to the base panel. Secure them using 4x cam locks (part 122998) and 4x screws (part 114254).
Step 5: Attach Top Support Pieces
Attach 4x top support pieces (part 153548) to the top of the side panels. Tap them into place with a hammer.
Step 6: Attach Wall Mounting Brackets to Unit (Part 1)
Attach 2x wall mounting bracket components (part 106989) to the back of the assembled unit using 2x screws (part 109049) and 2x small screws (part 100823).
Step 7: Place Glass Top
Carefully place the glass top (parts 10066373, 10087006) onto the assembled unit, ensuring correct alignment.
Step 8: Attach Brackets to Glass Top
Attach 3x brackets (part 10003193) to the underside of the glass top, aligning them with the pre-drilled holes.
Step 9: Secure Brackets to Unit
Secure the brackets (part 10003193) to the main unit using 3x screws (part 109560).
Step 10: Attach Wall Mounting Brackets to Unit (Part 2)
Attach the remaining 2x wall mounting brackets to the back of the unit.
Step 11: Position Unit Against Wall
Move the assembled unit into its final position against the wall.
Step 12: Prepare Wall for Mounting
Mark the wall through the holes in the wall mounting brackets. Drill holes and insert wall plugs if necessary, according to your wall type (refer to pages 16-18 for guidance on wall types A, B, and C).
Step 13: Secure Unit to Wall
Secure the unit to the wall using 2x screws (part 109048) and potentially 2x screws (part 100823) into the wall brackets and wall plugs.
Step 14: Prepare Drawer Components
Attach 2x drawer runners (part 118331) to the drawer side panels.
Step 15: Assemble Drawer Sides
Connect the drawer side panels using 2x dowels (part 101345).
Step 16: Assemble Drawer Frame
Assemble the drawer frame using 2x cam locks (part 110630).
Step 17: Attach Drawer Bottom
Slide the drawer bottom panel into the grooves and secure it with 1x screw (part 105344).
Step 18: Attach Drawer Front Support
Attach 1x drawer front support piece (part 152123) to the front of the drawer assembly.
Step 19: Insert Drawer Back Panel
Slide the drawer back panel into place.
Step 20: Attach Drawer Front Panel
Attach the drawer front panel using 4x screws (part 110519).
Step 21: Secure Drawer Bottom Support
Secure the drawer bottom support piece using 1x screw (part 105344).
Step 22: Insert Assembled Drawer
Carefully slide the assembled drawer into the unit.
Step 23: Adjust Drawer
Adjust the drawer alignment if necessary using the 2x adjustment screws (part 109558).
