EIFFEL
Installation Guide

General Specifications

Installation Instructions

A. Mounting Surface Preparation: Ensure that the mounting surface can adequately support the weight of the pedestal and withstand mechanical forces associated with charger usage.

B. Anti-Collision Protection: Appropriate anti-collision protection must be provided by the customer when mounting the Eiffel pedestal in parking spaces.

C. Foundation Responsibility: The calculation, design, and manufacture of the concrete foundation lie within the scope of responsibility of the site's producer.

D. Foundation Requirements: A horizontal, level, and sound foundation is required for installation.

E. Drainage: The base must permit the adequate run-off for accumulated water.

F. Surface Material: Do not mount the pedestal on asphalt. The stability of the pedestal on asphalt is not guaranteed. Wallbox recommends mounting the Eiffel pedestal on a concrete foundation.

G. Ventilation and Sunlight: Install the pedestal in a sufficiently ventilated area. Do not install it in direct sunlight.

H. Prohibited Installation Locations: Do not install your Wallbox pedestal near:

• Flammable, explosive, or combustible materials.
• Chemicals or solvents.
• Gas pipes or steam outlets.
• Heat emitters such as radiators or batteries.
• Areas prone to flooding, high humidity, and running water.

Overview

1. Mono Installation Pedestal: Designed for the installation of one charger.

2. Dual Installation Pedestal: Designed for the installation of two chargers. For dual installation of Eiffel, an extra mounting plate is required and must be purchased separately.

3. Charger Compatibility: Each Wallbox charger is compatible only with a specific model of Eiffel. Compatible chargers include:

• Pulsar Family
• Copper SB
• Commander 2
• Quasar

Tools and Mounting Parts

Required Tools

• A. Hammer
• B. Electric Drill with Ø12mm bits
• C. Torx T20 & T25
• D. Cabling Tools
• E. Socket Spanner

Included Mounting Parts

• F. Bolt Anchors (Quantities vary by SKU: x6 for Pulsar/Commander 2, x7 for Copper SB/Quasar)
• G. Screws

Notes

• For dual installation of Eiffel, an extra charger adapter plate is needed. This plate is sold as a separate accessory.
• A rain cover plate can be purchased separately if the Eiffel pedestal is to be installed outdoors. For dual installation, two rain cover plates will be required.
• Rubber grommets and cabling tools are not included in the installation kit and must be purchased by the customer.

1 - Mounting Base

Diagram shows a concrete foundation with dimensions 400mm x 250mm, with a 300mm depth for the foundation. An empty conduit is shown entering the foundation, with cables inside. The cable length is specified as 1.7m.

A. Foundation Construction: Build a concrete foundation with an empty conduit and lay all the cables in the center of the foundation.

B. Cable Length: Ensure the cables have appropriate excess length for the remaining installation. Cable length: 1.7m.

C. Packaging: Open the packaging and obtain the mounting parts needed for the installation.

2 - Drilling

A. Positioning Template: Place the drilling template on the top of the foundation, pass the power supply cable through the center hole, and mark the positions of the four boreholes on the concrete foundation.

B. Drilling Holes: Remove the drilling template and drill four holes.

C. Anchor Bolt Preparation: Remove the nuts and washers from the anchor bolts.

D. Anchor Insertion: Insert the anchors in the drilled holes, ensuring they are leveled and at least 40mm above the top of the foundation.

3 - Mounting

A. Pedestal Placement: Remove the pedestal from the packaging and then place the pedestal carefully over the four anchor screws.

B. Securing Pedestal: Place the washers and the nuts over the anchor screws and tighten the screws with the socket spanner extension. Tighten the iNDEX screws up to 34 Nm for Masonry and 54 Nm for concrete.

D. Charger Installation: Install the charger according to instructions in its installation manual.

For Dual installation, you will have to purchase a separate charger adapter plate and install the charger at the back panel of the pedestal.

E. Fixing Plug Holder: Fix the plug holder on the front panel by inserting the screws on the threaded holes.

4 - Electric Connections (Accessory)

A. Connection Box Cover: Open the cover of the connection box and remove the thin plastic cover on the required number of cable ports. Only one cable must be drawn through each grommet to ensure the IP protection.

You can purchase the electric connections box and the front adapter plate separately. The electrical connection box can be adapted for up to 24 DIN rail mountings to enable dual installation if required.

B. Positioning Electrical Box: Remove the protective caps inside the Electrical Box and center it with the four screws inside the pedestal.

C. Securing Electrical Box: Fix the Electrical Box to the pedestal by inserting the four nuts on the screws. Ensure to place the protective caps back on the screws.

5.a - Electric Wiring: Single Charger

A. Single Charger: Single Phase Wiring:

• 1. Cables from power supply
• 2. Cables to charger
• 3. Cable to pedestal's earthing
• (Diagram shows connections for L1, N, PE)

B. Single Charger: Three Phase Wiring:

• 1. Cables from power supply
• 2. Cables to charger
• 3. Cable to pedestal's earthing
• (Diagram shows connections for L1, L2, L3, N, PE)

5.b - Electric Wiring: Dual Chargers

A. Two Chargers: Single Phase Wiring:

• 1. Cables from power supply
• 2. Cables to charger
• 3. Cable to pedestal's earthing
• (Diagram shows connections for L1, N, PE for two chargers)

B. Two Chargers: Three Phase Wiring:

• 1. Cables from power supply
• 2. Cables to charger
• 3. Cable to pedestal's earthing
• (Diagram shows connections for L1, L2, L3, N, PE for two chargers)

Safety, Legal, Warranty, and Disposal Information

Safety Recommendations

• Follow all safety and installation instructions carefully. Failure to follow instructions may be a safety hazard and/or cause equipment malfunction.
• Any resulting damage due to disregard or actions contrary to the instructions in this manual is excluded from the product warranty.

Legal Notice

• Any information in this manual may be changed without prior notice and does not represent any obligation on the part of the manufacturer.
• Images in this manual are for illustration purposes only and might differ from the delivered product.

Safety and Maintenance Instructions

• Do not use this product if the enclosure is broken, cracked, open, or shows any other indication of damage. Please contact your distributor.
• The installation, maintenance, and servicing of the Eiffel pedestal must be performed only by qualified personnel in accordance with applicable local regulations. Unauthorized installation and modifications make the manufacturer warranty void.
• A minimum of two installers are required to perform the installation process for Wallbox Eiffel.
• Only Wallbox chargers should be installed on the pedestal.
• Wear safety shoes, glasses, and gloves as required by local regulations during installation.
• Protect your pedestal from any external impact.
• Do not use your pedestal under adverse climatic conditions.
• Do not open the door of the pedestal in rain.
• Take appropriate precautions with electronic medical implants.
• Disconnect main service power to the pedestal before cleaning the unit.
• Do not use cleaning solvents to clean any part of the charger or the pedestal. Clean it with a clean, dry cloth to remove dust and dirt accumulation.

Electrical Precautions

• The power supply line must be wired to an existing installation and must be in accordance with local regulations.
• The pedestal must be permanently connected to the electrical Earth of the installation.

Limited Warranty

• Wallbox warrants this product against defects in materials and workmanship for a period of 3 years from the date of purchase.
• During this period, at its discretion, Wallbox will either repair or replace any defective product at no charge to the owner.
• Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original warranty or six months, whichever is greater.
• Any defect resulting from any accident, misuse, improper maintenance, or normal wear and tear is not covered by the limited warranty.
• Substitution or incorporation of any part by the client will be considered as incorrect usage.
• Except to the extent permitted by applicable law, the terms of this limited warranty do not exclude, restrict, or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Wallbox for instructions on where to send or bring it for repair.

Disposal Advice

In accordance with directive 2012/19/EC, at the end of its useful life, the product should not be disposed of as urban waste. It should be taken to a collection center or a distributor that provides disposal of special and differentiated waste.

Service

Need more assistance? Contact Wallbox customer service:

support.wallbox.com

service@wallbox.com