Wireless Headset

Product Overview

The wireless headset features a design with distinct left and right earcups. Key components and controls are located as follows:

• Left Earcup: Houses the port for the detachable microphone and the AUX line-in port.
• Right Earcup: Contains the charge port.
• Boom Arm: Equipped with a microphone mute switch.
• On-Headset Controls: Buttons for power (hold on/off), play/pause/answer/end calls (single click), volume up/next track (single click/hold), and volume down/last track (single click/hold).
• Indicators: An LED indicator displays various status lights.

What's Included

• Wireless headset
• Microphone
• Aux cable
• USB-C charging cable

Pairing Instructions

1. Power on the headset by pressing the ON/OFF switch. A chime will sound, and the indicator light will flash rapidly white.
2. Use your device's Bluetooth settings to pair with "HEYDAY HEADSET 01".
3. The indicator light will flash slowly white once pairing is successful.

Indicator Lights

• Red/White Alternating: Bluetooth pairing mode.
• Slow Flashing White: Headset is paired.
• Slow Flashing Red: Battery is low.
• Red: Charging.
• White: Charging is complete.
• Ascending Tones: Powering on.
• Descending Tones: Powering off.
• Three Rapid Tones: Ready to pair.
• Two Rapid High Tones: Paired.
• Two Rapid Low Tones: Low battery.
• Two Ascending Tones: Maximum volume reached.
• Two Descending Tones: Minimum volume reached.

Headset Controls

• ON/OFF: Long press the "O" button.
• Play/Pause: Single click the "O" button.
• Pick up/Hang up Calls: When calling, single click the "O" button.
• Reject Call: When calling, long press the "O" button.
• Volume Up: Single click the "+" button.
• Volume Down: Single click the "-" button.
• Next Song: Long press the "+" button.
• Previous Song: Long press the "-" button.

Detachable Microphone

To use the microphone, insert it into the jack located on the left side of the headset. Ensure the microphone hole faces towards your mouth for optimal voice quality.

• The microphone's switch functions only when it is installed.
• Microphone On: Push the microphone switch upwards [green indicator].
• Microphone Off: Push the microphone switch downwards [red indicator].

Using AUX Mode

Connect the headset to other devices in wired mode using the included Aux cable. Note that when the Aux cable is plugged in, the Bluetooth function will be disabled until the cable is disconnected.

Charging the Headset

• A full charge takes approximately 2-3 hours.
• The charging indicator light turns solid white when charging is complete.
• Plug the Type-C end of the charging cable into the headset's charge port.
• Connect the USB end of the charging cable to a DC 5V USB power supply.

Troubleshooting and Tips

• Microphone Issues: Ensure the microphone is correctly installed and the microphone switch is in the 'on' position.
• General Reset: If the headset is not working correctly, turn it off and then on again.
• Not Turning On: Recharge the battery and try again.
• Charging Problems: Verify the power supply is working, provides 5V/1A, and is not damaged.
• No Sound: Adjust the volume.
• Not Connecting/Visible: Ensure the headset is not paired to another device. If it is, unpair it and then re-pair with your desired device.
• Pairing Code: This device does not require a pairing code. If prompted, ensure you are connecting to the correct device. If issues persist, try "forgetting" the device in your Bluetooth settings and re-pairing.

NOTE: The headset will automatically power off if it does not connect to another device within 2 minutes. Maintain a distance of less than 22 feet between the headset and connected devices for optimal performance.

Need Assistance?

For pairing issues, call acceptance problems, or general questions, please contact support:

[phone-icon] Call us at: 877-698-4883

Online at: TargetTechSupport.com

Safety Precautions

• Do not use the headset near any water source.
• Do not modify or attempt to repair the device yourself.
• Avoid using the headset in high temperatures or extreme weather conditions.
• Clean the device using a soft, dry cloth; do not use chemical detergents.
• Do not excessively bend the headband to ensure its longevity and prevent accidental breakage.

FCC Compliance Information

heyday

FCC ID: 2AVTM-TT2235 Model: TT2235 Input: 5V-Max 1A Made in China

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Target Corp. Mpls. MN, 55403 Phone: 1-612-304-6073