VEVOR Kids Toy Open Organizer
Model: ZHSNG-05
Affordable. Reliable. Home Improvement.
Introduction
This document provides the original instructions for the VEVOR Kids Toy Open Organizer, model ZHSNG-05. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product is subject to what you received. Updates to technology or software may occur without prior notice.
Safety Instructions
Please read the following precautions carefully before assembly!!
- This product is not suitable for children under 3 years old.
- For home use only; Indoor use only.
- Warning! Contains small component hazards before assembly; for adult assembly only.
- Please place on a flat and spacious ground, with appropriate open space around the installation area.
- Do not place in water or permeable ground, uneven or rough ground, slope, or other unsuitable places.
- Before use, please carefully check whether all parts are firm and whether there are other unsafe factors around.
- During use, please check the product body and nuts regularly. If there is breakage or wear, please stop using; otherwise, rollover or other hazards may occur.
- If a product nut has been worn and cannot be tightened, contact the manufacturer to purchase and replace the corresponding parts.
- The packaging is not a toy; please keep it properly and away from infants to avoid danger.
- Store in a cool and dry place, away from direct sunlight, and away from fire and heat sources.
- The maximum load of this product is 15 kg; do not use overweight.
- Be sure to use under adult supervision; do not allow children to play with toys that have been disintegrated, damaged, or deformed to avoid accidental swallowing, choking, and other injuries.
- Please save the instructions for future reference.
Thank you for choosing this KIDS TOY OPEN ORGANIZER. Please read all instructions before use to achieve the best possible results. SAVE THIS MANUAL.
Parts List
| Part Name | Description of Picture | Number | Remark |
|---|---|---|---|
| S23001 Cabinet eave | A decorative, house-shaped top piece. | 1 | |
| S23003 Cabinet layer | A horizontal shelf piece. | 1 | |
| S23004 Cabinet back board | A large, flat back panel. | 1 | |
| S23017 Storage side plate | A side panel with multiple holes and slots for assembly. | 1 | |
| S23018 Storage side plate | A side panel with multiple holes and slots for assembly. | 1 | |
| NO.8 Short layer board | Shorter horizontal shelf pieces. | 2 | |
| NO.9 Cabinet door panel | A panel that functions as a door. | 1 | |
| NO.10 Cabinet backing plate | A smaller back panel piece. | 1 | |
| NO.12 Short leg trip | Short leg-like supports. | 2 | |
| S21101 Small storage box | Small, individual storage bins. | 10 | |
| X Small cross nut | A type of fastener (cross-shaped head). | 16 | |
| Z2 Large cross nut | A larger type of fastener (cross-shaped head). | 30 | |
| LS90 Right Angle screw | A screw designed for right-angle connections. | 2 | |
| Y2 Round head screw | A screw with a rounded head. | 2 | |
| S21103 Fillet buckle | A connecting buckle or clip. | 2 | |
| C19103 Cross nut tool | A tool for tightening cross nuts. | 1 | |
| NO.S2 Front baffle | A front panel piece with multiple openings. | 1 | |
| S3 Tree layer | A shelf piece with a tree-like design. | 1 | |
| S4 Bird layer | A shelf piece with a bird-like design. | 2 | |
| S21001 Storage side panels | Main vertical side panels for the storage unit. | 4 | |
| Storage pole | Vertical rods for support. | 8 | |
| S21002 Long layer board | A long horizontal shelf piece. | 1 | |
| W21006 Painting board | A board for drawing or display. | 1 | |
| W21005 Painting board fixed plate | A plate to secure the painting board. | 1 | |
| D21104 Painting board top leaf | A top decorative piece for the painting board. | 1 | |
| D21108 Drawing board screws | Screws specifically for the drawing board. | 4 | |
| W19115 Rubber non-slip mat | A mat to prevent slipping. | 1 | |
| W19106 Rotating cross nut | A nut that allows rotation. | 8 | |
| W19107 Top figure buckle | A buckle for securing the top. | 3 | |
| W19109 Bottom figure buckle | A buckle for securing the bottom. | 3 | |
| Iron screw | Standard iron screws. | 9 | |
| T-shaped anti-tipping accessory | Safety accessory to prevent tipping. | 1 |
Assembly Steps
Step 1
Tighten the cabinet eave (S23001) by pressing the round screw and X small cross nut from the top down. Then, install the 90° screw and tighten it with an X small cross nut. Put aside temporarily. Note the direction of the 90° screws.
[Diagram: Shows the S23001 cabinet eave being assembled with Y2 round head screws, LS90 right angle screws, and X small cross nuts.]
Step 2
Attach the S23004 cabinet back board, S23003 cabinet layer, and NO.8 short layer board. Use cross nuts to fix and tighten the S23018 storage side plate with the other side plate using X small cross nuts and Z2 large cross nuts.
[Diagram: Shows the back board, cabinet layer, short layer board, and side plates being joined using X small cross nuts and Z2 large cross nuts.]
Step 3
Attach the S21103 fillet buckle, the NO.9 cabinet door panel, and plug in the NO.10 cabinet backing plate and the NO.12 short leg trip.
[Diagram: Shows the fillet buckle, door panel, backing plate, and leg trip being attached to the assembly.]
Step 4
Fasten and tighten the nut. Cover the S23017 storage side panels with Z2 large cross nuts and X small crosses fillet buckle.
[Diagram: Shows the S23017 storage side panels being secured with Z2 large cross nuts and fillet buckles.]
Step 5
Screw on the W19106 rotating cross nut and place the S21101 small storage box. The house storage cabinet is now installed. Set aside for now.
[Diagram: Shows the rotating cross nut being attached and storage boxes being placed into the house-shaped cabinet.]
Step 6
Insert the S21002 long layer board into the two holes on the top of the S21001 storage side panel, and fix it with the Z2 large cross nut.
[Diagram: Shows a long layer board being inserted into side panels and secured with a Z2 large cross nut.]
Step 7
Insert the storage poles (8 total) into the base.
[Diagram: Shows vertical storage rods being inserted into a base panel.]
Step 8
Insert the storage poles one by one into the base.
[Diagram: Shows multiple storage rods being inserted into the base panel.]
Step 9
Cover with another S21001 storage side panel and fix it with a Z2 large cross nut.
[Diagram: Shows a second side panel being placed on top of the rods and secured with Z2 large cross nuts.]
Step 10
Press both sides of the assembly inward and turn 180 degrees.
[Diagram: Shows a rotational action of the assembled structure.]
Step 11
Secure with Z2 large cross nuts.
[Diagram: Shows Z2 large cross nuts being used to secure the structure.]
Step 12
Put the assembled unit into the box. The installation is complete.
[Diagram: Shows the completed storage unit being placed into a larger container or base.]
Step 13
First, fix 2 storage poles to the S21001 storage side panel. Use a Z2 cross nut to secure it.
[Diagram: Shows two storage poles being attached to a side panel with Z2 cross nuts.]
Step 14
Lay the loaded side on the ground. (Implies flipping the assembly from the previous step).
[Diagram: Shows a base assembly being laid flat, possibly after being overturned.]
Step 15
Start with the NO.S2 front baffle. Insert it into the corresponding hole.
[Diagram: Shows the front baffle being inserted into a base panel.]
Step 16
Insert the S4 bird layer. Ensure it is stuck in the top slot.
[Diagram: Shows the S4 bird layer being inserted into a slot, with a close-up indicating it should be seated in the top slot.]
Step 17
Insert the layers (S3 Tree layer, S4 Bird layer) in sequence as in the previous step. The order of the layers is determined by the front baffle. Ensure they are stuck in the top slot.
[Diagram: Shows multiple layers (S4, S3) being inserted sequentially into the assembly, with a close-up indicating they should be seated in the top slot.]
Step 18
Cover the storage side panels (S21001) and secure them with X small cross nut and Z2 large cross nut respectively.
[Diagram: Shows storage side panels being placed over the inserted layers and secured with X small cross nuts and Z2 large cross nuts.]
Step 19
Press both sides of the hands inward and turn 180 degrees.
[Diagram: Shows a rotational action of the assembled structure.]
Step 20
Secure with X small cross nut.
[Diagram: Shows X small cross nuts being used to secure the assembly.]
Step 21
Install the fixing screws on the back to make the layer board more firm.
[Diagram: Shows screws being inserted into the back of the assembly for added stability.]
Step 22
The W21005 painting board fixed plate is covered with a W19115 rubber non-slip mat. The bookshelf and the painting board fixing plate are connected using the W19106 rotating cross nut, W19109 bottom figure buckle, and W19107 top figure buckle to secure.
[Diagram: Shows the painting board fixing plate with the rubber mat being attached to the bookshelf structure using various buckles and nuts.]
Step 23
Secure the W21006 painting board with the D21108 drawing board screws. Then, use the D21104 painting board top leaf to press from back to forward onto the drawing board.
[Diagram: Shows the painting board being attached with screws and a top leaf component being pressed into place.]
Step 24
Stick the T-shaped anti-tipping accessory to the wall and the cabinet for safety. Connect the painting board to the cabinet installed in front. Move the S21103 fillet buckle on the cabinet to the corresponding position, connect the bottom figure buckle, and tighten the top figure buckle and the rotating cross nut.
[Diagram: Shows the anti-tipping accessory being attached and the painting board being connected to the main cabinet structure.]
Product Parameters
| Parameter | Value |
|---|---|
| Model | ZHSNG-05 |
| Color | White and Beige |
| Material | HDPE |
| Product Size | 2250*375*915mm |
Manufacturer and Distributor Information
Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX
EU Representative: E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.
