NZXT Kraken X Series AIO RGB Liquid Cooler

Product Overview

NZXT Kraken X Series (240mm / 280mm / 360mm) Liquid Cooler with RGB.

Model numbers include RL-KRX53-01, RL-KRX63-01, RL-KRX73-01.

Component List

• A. Kraken X53 / X63 / X73 (x1)
• B. Intel Retention Bracket (Pre-Installed) (x1)
• C. AMD Retention Bracket (x1)
• D. Intel Backplate (x1)
• E. Intel Socket 1200/115X Standoff (x4)
• F. Intel Socket 1700 Standoff (x4)
• G. AMD Standoff (x4)
• H. AMD Sleeves (x4)
• I. 30mm UNC 6-32 Fan Screw (X53/X63: x16, X73: x12)
• J. 5mm UNC 6-32 Screw (X53/X63: x8, X73: x12)
• K. Washer (X53/X63: x16, X73: x24)
• L. Thumbscrew (x4)
• M. Breakout Cable Set (x1)
• N. Micro-USB Cable (x1)
• O. Fan Splitter Cables (1 to 3 split) (x1)
• P. Aer P Fan (X53: 120mm x2, X63: 140mm x2, X73: 120mm x3)

Installation - Intel LGA 1700/1200/115X

Preparation

Ensure you have the necessary components for Intel LGA 1700/1200/115X sockets.

Installing the Backplate

Step 1: Adjust the sliders on the Intel backplate (D) to the innermost positions for Socket 1200/115X or the outermost positions for Socket 1700.

Step 2: Install the Intel backplate (D) on the rear of the motherboard, ensuring the sliders align with mounting holes and the CPU socket backplate fits within the backplate's cut-out.

Installing the Standoffs

Step 3: From the front of the motherboard, install the four Socket 1200/115X/1700 standoffs (E or F).

Changing the Retention Bracket

This section details how to switch between Intel and AMD retention brackets if needed, though the primary Intel installation uses the pre-installed bracket (B).

Installing the Pump

Step 4: Place the pump with the retention bracket (B) onto the CPU. Ensure the standoffs (E or F) go through the holes on the bracket and securely apply the thumbscrews (L).

The pump cap has a rotatable upper cap with 12 locking points for NZXT logo orientation. Depending on your motherboard layout, you can orient the pump's tube direction as needed.

Installation - AMD AM4/AM5/TR4/STRX4

Preparation

Ensure you have the necessary components for AMD sockets.

Installing the Pump - AMD AM5, AM4, TR4, STRX4

Step 1: Remove the stock AMD mounting bracket and keep the original backplate on the rear of the motherboard. (Note: For Socket TR4, skip to AMD - Step 4).

Step 2: From the front of the motherboard, install the four AMD sleeves (H). Ensure you use the correct orientation based on the socket name facing upwards.

Step 3: From the front of the motherboard, install the four AMD standoffs (G).

Step 4: Mount the pump with the appropriate retention bracket (C) onto the CPU. For AMD AM4/AM5, use thumbscrews (L) to secure the pump to the standoffs (G). For Socket TR4, use the specific screws provided with the Threadripper CPU retail box and align them carefully.

For Socket TR4, install the AMD Socket TR4 retention bracket (included in the Threadripper CPU retail box). Mount the pump with the retention bracket onto the CPU. The Socket TR4 screw holes have a short and long side. Ensure the four screws are aligned and tighten them in sequence from 1 through 4.

Mounting the Radiator and Fans

Depending on your radiator mounting setup, use the appropriate screws to mount the radiators.

Note: Always use washers (K) to prevent damage.

Direct Mounting

For mounting where the radiator fits directly onto the case, install the fan(s) (P) first using 30mm fan screws (I) and washers (K). Then, use 5mm case screws (J) and washers (K) to mount the radiator to the case.

Indirect Mounting

For mounting where the fan(s) (P) fit between the radiator and chassis, use the 30mm fan screws (I) and washers (K) for mounting the fans to the radiator.

Connections

Connecting the Pump Tach

Connect the 3-pin connector from the breakout cable set (M) to the motherboard's 4-pin CPU_FAN or AIO_PUMP header.

Note: You may need to disable fan-fail warning within the motherboard BIOS if CPU_FAN is unused.

Connecting the SATA Power Cable

Connect the SATA power cable from the power supply unit to the pump's power connector (part of the breakout cable set M).

Powering the Fans

You may use the included fan splitter (O) to connect the fans (P) to your motherboard or a fan controller (not included). Refer to the fan controller manufacturer's documentation for specific power requirements.

Connecting the USB Cable

Connect the Micro-USB cable (N) from the pump to an available USB 2.0 internal connector on the motherboard.

Downloading NZXT CAM

After setting up the Kraken, turn on your PC and proceed to download and install the NZXT CAM software from nzxt.com/camapp/ to enable Kraken controls and monitoring.

Regulations and Compliance

Designed in Los Angeles, California. Made in China.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (B) / NMB-3 (B)

Maximum ambient temperature: 50°C. Maximum normal operating temperature (coolant): 60°C. Maximum abnormal temperature (coolant): 70°C.

This equipment is not suitable for use in locations where children are likely to be present.

RoHS Compliance:

The following substances are restricted according to SJ/T 11364 and GB/T 26572 standards:

NZXT Global Warranty Policy

I. Warranty Length

Any replacement product is covered for the remainder of the warranty period or thirty days, whichever is longer. Proof of purchase is required.

II. Who is Protected

The warranty covers NZXT products purchased by the original consumer.

III. What is and is Not Covered

NZXT will provide a repaired or replacement product (new or refurbished) for malfunctions within the warranty period. Our warranty does not cover:

• Product or serial number modification without NZXT permission.
• Damage that is not a manufacturing defect.
• Damage resulting from accident, abuse, misuse, neglect, fire, water, lightning, acts of nature, unauthorized modification, or failure to follow instructions.
• Improper installation, unauthorized alterations, or attempted repair by unauthorized personnel.
• Shipping or transport damage (claims must be made with the carrier).
• Normal wear and tear.

NZXT does not warrant that the product will meet your specific requirements; it is your responsibility to determine suitability.

NZXT covers two-way return shipping for Store orders. For other authorized dealers, NZXT Support covers one-way shipping from NZXT back to the end-user for exchanges.

IV. Exclusion of Damages

NZXT's liability is limited to repair or replacement. NZXT is not liable for incidental or consequential damages, including loss of data, business interruption, or tort liability.

V. Limitations of Implied Warranties

Implied warranties (merchantability, fitness for a particular purpose) are limited to the specified warranty length.

VI. To Obtain Technical Support

Contact NZXT Support via phone at +1 (800) 228-9395, email at service@nzxt.com, or visit nzxt.com/customer-support.

VII. How to Obtain Warranty Service

Submit a request via the NZXT Support site. Provide proof of purchase. Upon approval, you will receive an RMA number and instructions to ship the defective item back to NZXT.

VIII. Applicable Law and Additional Legal Rights for Consumers

This warranty is governed by California law. Consumers may have additional rights under local consumer protection laws.

IX. Warranty Service from Resellers

Contact your dealer or reseller for service within the warranty period. For returns outside of North America, Europe, and Australasia, contact the retailer or distributor.

X. NZXT.COM Store Returns/Exchange Policy

Eligible products can be returned or exchanged within 30 days of purchase with an authorized RMA number. Returns beyond 30 days are not allowed. Refunds are credited to the original payment method.

Support and Service

For questions or problems with your NZXT product, please contact NZXT Support at support.nzxt.com. Include a detailed explanation of your problem and proof of purchase.

For comments and suggestions, email designer@nzxt.com.

Visit the NZXT website for more information: nzxt.com.

Warranty coverage and service information is available at nzxt.com/warranty and support.nzxt.com.

NZXT, Inc.
15736 E. Valley Blvd, City of Industry, CA 91744, USA

NZXT Europe GmbH
Industriering Ost 66 | 47906 Kempen | Germany

Contact: +1 (800) 228-9395 / service@nzxt.com / nzxt.com